Page 4
FE170CG Outline • System Block Diagram • System Block Diagram • Component and PCB Board Introduction • Component and PCB Board Introduction • Power On Sequence • Power On Sequence • Equipment Requirement • Equipment Requirement • Trouble Shooting Guide...
Page 5
Outline Introduction (TOP) Camera Speaker Micro phone...
Page 6
Outline Introduction (BOT) Camera Volume Key Micro-SD Micro-SIM Power Key...
Page 8
PCB Board Introduction (TOP) Front Camera Rear Camera GPS & BT 2076 WIFI 43362 SD Connector EMMC ULPI ULPI MDM 6360 SIM2 Connector MDM LPDDR1 Charger IC SIM1 Connector eMMC...
Page 9
PCB Board Introduction (BOT) Touch IC Touch Connectors Trianceiver SMARTI Codec 5648 G Sensor INTEL CTLP+LPDDR2 RF POWER AMP PMIC SNB5072 Gauge IC Battery Connector Connector...
Page 10
FE170CG Outline • System Block Diagram • System Block Diagram • Component and PCB Board Introduction • Component and PCB Board Introduction • Power On Sequence • Power On Sequence • Equipment Requirement • Equipment Requirement • Trouble Shooting Guide...
Page 12
FE170CG Outline • System Block Diagram • System Block Diagram • Component and PCB Board Introduction • Component and PCB Board Introduction • Power On Sequence • Power On Sequence • Equipment Requirement • Equipment Requirement • Trouble Shooting Guide...
Page 13
• Power supply: DC 4V • Oscilloscope • Oscilloscope • Digital Multi-Meter • Digital Multi-Meter • AC charger of FE170CG • AC charger of FE170CG • Battery of FE170CG • Battery of FE170CG • Micro USB cable • Micro USB cable •...
Page 14
FE170CG Outline • System Block Diagram • System Block Diagram • Component and PCB Board Introduction • Component and PCB Board Introduction • Power On Sequence • Power On Sequence • Equipment Requirement • Equipment Requirement • Trouble Shooting Guide...
Page 16
Trouble Shooting Guide no boot Check the BATT have 3.7V or not, Check the BATT have 3.7V or not, • • – BATT voltage < 3.5V -->Changer,Wait battery voltage >3.7V,Boot again – BATT voltage < 3.5V -->Changer,Wait battery voltage >3.7V,Boot again •...
Page 18
Trouble Shooting Guide power on no display • Check • Check U1605,U160 U1605,U160 3,R1601 3,R1601 have open have open or short or short • Check VLED • Check VLED voltage9.3~ voltage9.3~ 10.35V 10.35V...
Page 19
Trouble Shooting Guide can not charge Plug USB cable then check • R1303.1 &PL8101 =5V. Check CHGOUT=3V~4.2V. • Check CHG_EN=0V • Check PR8117,PU8101 open or •...
Page 20
Trouble Shooting Guide can not cable power on • Check PU8401,U1201,PR8612 have open or • Check PU8401,U1201,PR8612 have open or short short • Plug in USB charger then check C1204.1 • Plug in USB charger then check C1204.1 voltage=5V voltage=5V •...
Page 24
Trouble Shooting Guide Speaker • Check U1502, CON1702 ,L1303, L1302 have • Check U1502, CON1702 ,L1303, L1302 have open or short open or short • Check U1502 And peripheral circuit have open • Check U1502 And peripheral circuit have open or short or short...
Page 28
Trouble Shooting Guide eMMC • Check U1102 have open • Check U1102 have open or not or not • Check +3vsus=3.3V • Check +3vsus=3.3V • Check • Check emmc_vccq_1p80=1.8V emmc_vccq_1p80=1.8V...
Page 29
Trouble Shooting Guide G sensor • Check U1801 have • Check U1801 have open or not open or not • Check VDDIO_ACC • Check VDDIO_ACC &VDD_ACC =1.8V &VDD_ACC =1.8V • Check ACC_AD0=0V • Check ACC_AD0=0V • Check R1809,R1811 • Check R1809,R1811 have open or not have open or not...
Page 33
Trouble Shooting Guide SD Card • Check • Check SD_VCCSDIO=2.85V/1.8 SD_VCCSDIO=2.85V/1.8 • Check SDCONN1 have • Check SDCONN1 have open or short open or short • Check • Check SDIO0_DET_N=1.8V SDIO0_DET_N=1.8V...
Page 34
Trouble Shooting Guide_SUB Touch error • Check SENSOR has connected to MB • Check SENSOR has connected to MB • TP_CON1,TP_CON2 have open or damage • TP_CON1,TP_CON2 have open or damage • Check SENSOR FPC damage or not • Check SENSOR FPC damage or not •...