Europa Hilt EX5 Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Caution

Before using our chain saws.please read this

manual carefully to understand the proper use of

your unit.keep this manual handy.

CHAIN SAW

Table of Contents

Need help?

Do you have a question about the EX5 and is the answer not in the manual?

Questions and answers

Summary of Contents for Europa Hilt EX5

Page 1 Caution Before using our chain saws.please read this manual carefully to understand the proper use of your unit.keep this manual handy. CHAIN SAW...
Page 2: Table Of Contents
1. For Safe Operation Contents For Safe Operation----------------------------------------------------------------------------------------------------1 Explanation of Symbols on the Machine--------------------------------------------------------------------------4 Installing Guide Bar and Saw Chain-------------------------------------------------------------------------------5 Fuel and Chain Oil---------------------------------------------------------------------------------------------------- 6 Operating the Engine-------------------------------------------------------------------------------------------------8 Sawing------------------------------------------------------------------------------------------------------------------11 Maintenance-----------------------------------------------------------------------------------------------------------13 Maintenance of Saw Chain and Guide Bar----------------------------------------------------------------------15 Troubleshooting Guide----------------------------------------------------------------------------------------------16 10. Specifications---------------------------------------------------------------------------------------------------------17 Dear Customer, Firstly.
Page 3 1.For Safe Operation 1.For Safe Operation 1. Never operate a chain saw 8. Do not allow other persons to when you are fatigued, ill, or be near the chain saw when start- upset, or under the influence of ing or cutting. Keep bystanders medication that may make you and animals out of the work area.
Page 4 1. For Safe Operation damage to the flywheel could KICKBACK SAFETY PRECAUTIONS occur which could subsequently CHAIN SAW USERS cause the flywheel to disinte- grate.) WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and 16.
Page 5: Explanation Of Symbols On The Machine
2.Explanation of Symbols on the Machine 2.Explanation of Symbols on the Machine WARNING! For safe operation and screw under "H' maintenance, symbols are carved in relief on stamp is The High -speed adjustment screw. the machine. According to these indications, please be The screw under the "L"...
Page 6: Installing Guide Bar And Saw Chain
3.Installing Guide Bar and Saw Chain 3.Installing Guide Bar and Saw Chain A standard saw unit package contains the items NOTE Pay attention to the correct as illustrated. direction of the saw chain. Moving direction 4. Fit the chain cover to the power unit and fas- ten the nuts to finger tightness.
Page 7: Fuel And Chain Oil
4. Fuel and Chain Oil 4. Fuel and Chain Oil FUEL than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may conse- WARNING! Gasoline is very flamma- quently occur. ble.
Page 8 4. Fuel and Chain Oil WARNING! 1. Select flat and bare ground for fueling. 2 Move at least 10 feet (3 meters) away from fueling point before starting the engine. 3 Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container.
Page 9: Operating The Engine
5.Operating the Engine 5.Operating the Engine NOTE WARNING! When restarting immediately It is very dangerous to run after stopping the engine, set the Choke knob in a chainsaw that mounts broken parts or lacks the first-stage position (choke open and throttle any parts.
Page 10 5.Operating the Engine When adjusting, take the foIIowing steps: NOTE (1) Chain oil Be sure to adjust the carbu- retor with the bar chain attached. 1. "H" and "L" needles are restricted within the number of turn as shown below. "H"...
Page 11 5.Operating the Engine 2. Holding the chain saw horizontally, release mode which it is set at the time of shipment. your hand from the front handle, hit the tip of However when the possibility exists that icing the guide bar to a stump or a piece of wood, may occur, the unit should be set to operate in and confirm brake operation.
Page 12: Sawing
6.Sawing 6.Sawing This saw is equipped with a chain brake that will WARNING! stop the chain in the Before proceeding to event of kickback if oper- your job, read the sec- ating properly. You must tion "For Safe Oper- check the chain brake ation '.
Page 13 6.Sawing 3. Make a notch cut one-third of the way into Cutting the limbs of Fallen Tree the tree on the felling side. First check to which side the limb is bent. Then 4. Make a felling cut from the opposite side of make the initial cut from the bent side and finish the notch and at a level slightly higher than by sawing from the opposite side.
Page 14: Maintenance
7.Maintenance 7.Maintenance 3. Guide bar WARNING! Before cleaning, inspecting or repairing the unit, make sure When the guide bar is dismounted. remove saw- that engine has stopped cool. dust in the bar groove and the oiling port. Disconnect the spark plug to prevent acci- Grease the nose sprocket from the feeding port dental starting.
Page 15 7. Maintenance 2. Fuel filter 5. Front and Rear dampers 1. Using a wire hook, take out the filter from the Replace if adhered part is peeled or crack is filler porl. observed on the rubber part. Replace if the inside of the rear damper metal has been beaten by the stopper bolt and the clearance of the metal increased.
Page 16: Maintenance Of Saw Chain And Guide Bar
8.Maintenance of Saw Chain and Guide Bar 8.Maintenance of Saw Chain and Guide Bar 1.Saw Chain WARNING! It is very important for smooth and safe operation to always keep (1) Appropriate the cutters sharp. gauge checker (2) Depth gauge The cutters need to be sharpened when: standard (3) Make the shoul- Sawdust becomes powder-llke.
Page 17: Troubleshooting Guide
8.Maintenance of Saw Chain and Guide Bar/9.Troubleshootin Guide 3.Chain maintenance table WARNING! The characteristic data of the chain and bar homologated for this machine are shown in the“EC Conformity Statement”that accompanies same machine. Do not use other types of chain or. bar for safety reasons. The table gives the sharpening data for different types of Chain.
Page 18: Specifications
EN 17 10. Specifications 10. Specifications Chain saw Model 3800/4500/5200/5800 Mass ( without guide bar and chain) 5.50 (kg) Dimensions ( without guide bar and chain) 410x235x265 (mm) Fuel Mixture (Gasoline 25: Two-cycle oil 1 ) Fuel tank capacity 550 (ml) Chain oil Motor oil SAE#10W-30 oil tank capacity...