Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Nauto Nauto Device
- Page 1 Installation Guide Nauto Device & Mark Button US Installation Guide May 2019...
-
Page 2: Table Of Contents
Nauto Components ...................6 OBD Adapter Reference.................7 Installation Power Source Connection ..............8 OBD Connection ..................10 Power Cable Connection ...............11 Device Registration..................12 Device Installation ...................13 Vehicle Information .................15 Mark Button ....................16 Image Submission ..................17 Additional Resources ................18 © Nauto 2019. All Rights Reserved. -
Page 3: Overview
Overview © Nauto 2019. All Rights Reserved. - Page 4 Overview (cont.) © Nauto 2019. All Rights Reserved.
-
Page 5: Installation Tool List
18 AWG nylon butt connectors (2 or 3) Posi-Tap Requires posi-tap connectors to tap into wires without cutting or splicing. Proper sized posi-taps Solder Requires a heated tool to bond wires using a filler metal with low melting point. Soldering iron © Nauto 2019. All Rights Reserved. -
Page 6: Nauto Components
12V Power Supply Adapter 3-wire power supply with OBD Y-cable connector. Windshield Mounts Mark Button Fuse Holder with 4amp fuse Power Cable OBD Adapters See reference guide on page 7. © Nauto 2019. All Rights Reserved. © Nauto 2019. All Rights Reserved. -
Page 7: Obd Adapter Reference
Ford Round Snap-In • GM • Ford European Lock Mount • Mercedes Iveco Slide & Lock • BMW • Iveco Asian Snap-In • Toyota Volvo Slide Mount • Hyundai • Kia • Volvo • Ford © Nauto 2019. All Rights Reserved. -
Page 8: Installation
One Method for Locating Correct Vehicle Wires Use a multimeter. Set your multimeter to DC voltage. Attach the negative (-) probe to the vehicle chassis ground. Probe the wires you suspect of being the constant and ignition power sources. © Nauto 2019. All Rights Reserved. - Page 9 Using your preferred connection method (poke & wrap, solder, or posi-tap), connect the red wire from the Nauto power supply to the source of +12V. Be sure NOT to permanently disconnect the 12V source from other circuits in the vehicle and take care to make a strong connection to survive vibration and temperatures.
-
Page 10: Obd Connection
Select and install the vehicle-appropriate adapter from Nauto’s OBD Adapter Kit (page 6). 4. Using the appropriate adapter, replace the vehicle’s OBD port with the female end of the Nauto Y-cable. If there was an existing device in the vehicle’s OBD port, please reconnect it utilizing the Nauto Y-cable. -
Page 11: Power Cable Connection
The power supply is not waterproof and is intended to be placed inside of the vehicle. It is not designed to be mounted externally or under the hood of a vehicle. © Nauto 2019. All Rights Reserved. -
Page 12: Device Registration
The QR code is located on the will be provided to you prior to device. You may also manually installation. enter the serial number, which is located next to the QR code on the Nauto Device. © Nauto 2019. All Rights Reserved. -
Page 13: Device Installation
6. Locate the small screw on the accessible side of the device. Find this on the exposed side from the rearview mirror. Rotate the T5 screw clockwise to lock the Nauto Device into place. The other screw will not be tightened. - Page 14 Device Installation 8. Mark location for the Nauto Device. Using the live images as guidance, mark the location for the Nauto Device on the windshield with tape or marker. For optimal device performance: a. The forward-facing camera should have a clear view of the front of the vehicle with no obstructions.
-
Page 15: Vehicle Information
The barcode is located in the You will be prompted to vehicle. confirm that the device is Confirm with the fleet manager powered even when the vehicle the vehicle identifier for is locked Vehicle Name or ID. © Nauto 2019. All Rights Reserved. -
Page 16: Mark Button
You will need to activate manual pairing by pressing both volume buttons on the Nauto Device for at least 5 seconds, or until the LED lights on the de- vice flash blue. The Nauto Device will then search for a Mark Button to pair with. -
Page 17: Image Submission
Follow prompts to capture six (6) images of the vehicle. a. Odometer b. Install location c. Front of car d. Back of car e. Driver side Passenger side 2. Complete installation. Upload images through the Nauto Installer app to complete installation. © Nauto 2019. All Rights Reserved. -
Page 18: Additional Resources
Local dealer for vehicle manufacturer Links to external sites are not under the control of Nauto, inc. Therefore we are not responsible for the content of any linked site. Nauto, inc. Is providing these links to you only as a convenience, and the inclusion of any link does not imply endorsement by Nauto, inc.