Advertisement
Your Hydro Bottle
♦ Before using your Hydro Bottle, it is important to understand what is included and
how each part works. Please review the parts below and also reference this page for
any questions while reading through your instructions.
Base
Assembling Your Hydro Bottle
♦ To begin using your Hydro Bottle, first rinse out the interior of the glass body by
following the cleaning process on the previous page.
♦ We recommend charging your Hydro Bottle prior to the first use. To do so, first
ensure the Hydro Bottle is completely dry. Then, plug the charging lead into the
charging port on the base of the Hydro Bottle.
♦ Next, plug the USB into a compatible USB charging port or adaptor.
♦ Once the base is plugged in to a compatible outlet, the LED lights will be Red. Once
the unit is fully charged, the LED lights will turn off (approximately 2 hours).
♦ Once the unit is fully charged, your Hydro Bottle should last approximately 20-25
cycles without needing to be charged again. This will vary depending on what
Hydrogen process you most frequently use.
Lid
Strap
Charging
Glass Body
H2 Micro USB
Charging Lead
H2 Function
Button
Charging
Port
Using Your Hydro Bottle
♦ After the unit is fully charged, unplug the Hydro Bottle from the USB charging cord.
♦ Next you can fill the bottle up by turning the lid counter clockwise and adding in non-
flavored household drinking water, pure water, mineral water or carbonated water.
We recommend only pouring water until it reaches about ½ inch from the brim of
the top of the bottle.
USB
♦ Once the water has been added to the Hydro Bottle, secure the lid to the glass body
by turning the lid clockwise.
♦ Your Hydro Bottle has 2 different electrolytic processes, which will produce different
amounts of Hydrogen into the water.
♦ The first process will use electrolysis to increase the Hydrogen in your water to
approximately 750ppb (parts per billion) and will take 3 minutes from start to finish.
To use this function, press the function button 1 time. After pressing the function
button, the LED lights will turn to blue and the bottle will beep 1 time. You will notice
Cord
the water will look slightly cloudy, this is a normal part of the electrolysis process and
your water will return to normal once the function has completed. When the
electrolysis process is finished, the unit will beep 1 time and the LED lights will turn off.
You are now ready to enjoy your Hydrogen water.
♦ The second process will use electrolysis to increase the Hydrogen in your water to
approximately 930ppb (parts per billion) and will take 6 minutes from start to finish.
To use this function, press the function button 2 times quickly (within 3 seconds of
each other). After pressing the function button, the LED lights will turn to blue and the
bottle will beep 3 times. You will notice the water will look slightly cloudy, this is a
normal part of the electrolysis process and your water will return to normal once the
function has completed. When the electrolysis process is finished, the unit will beep 1
time and the LED lights will turn off. You are now ready to enjoy your Hydrogen
water.
♦ Enjoy the Hydrogen Water immediately, as the hydrogen will begin to slowly
dissipate as it sits. In order to consume the most Hydrogen rich water, it is
recommended to drink the water within 1 hour of the completion of the either
Hydrogen cycle ( listed above).
If you wish to stop the process during the cycle, simply hold down the function button
♦
until you hear 1 beep and the LED lights turn off.
Trouble Shooting Your Hydro Bottle
If your Hydro Bottle is in an electrolysis process and beeps three times, stops the
♦
process, and the LED light is blinking red; you're hydro bottle is low on battery and
needs to be placed on the charger.
If the product is fully charged but goes into stand by mode and beeps three times,
♦
check to make sure nothing is inside the bottle and ensure you are not using flavored
water.
Advertisement
