Table of Contents
Advertisement
Quick Links
WDV-18
18 GALLON WET/DRY VACUUM
PARTS & OPERATING MANUAL
Thank you for purchasing a Pacific Floorcare product. Carefully inspect all components for freight damage. If such
damage is discovered, file a "CONCEALED DAMAGE REPORT" immediately with the delivering carrier.
Read this manual carefully and keep it near the machine, protected from liquids and other damaging substances. Failure
to follow the instructions may result in injury or damage to equipment and property.
The contents of this manual are based on the latest product information available at the time of publication. Pacific
Floorcare reserves the right to make changes or improvements without being obliged to apply changes to the machines
previously sold.
New manuals can be downloaded from:
www.pacificfloorcare.com/manuals
Advertisement
Table of Contents
Summary of Contents for Pacific Floorcare WDV-18
- Page 1 18 GALLON WET/DRY VACUUM PARTS & OPERATING MANUAL Thank you for purchasing a Pacific Floorcare product. Carefully inspect all components for freight damage. If such damage is discovered, file a “CONCEALED DAMAGE REPORT” immediately with the delivering carrier. Read this manual carefully and keep it near the machine, protected from liquids and other damaging substances. Failure to follow the instructions may result in injury or damage to equipment and property.
- Page 2 18 GAL. WET/DRY VACUUM SPECIFICATIONS Features Specification Units Overall Machine Weight 69 lbs. Dimensions Width at body 18 In. Width at Squeegee 24 In. Length 28 In. Height 38 In. Noise Level 79 dBA Wheels Dimension Rear Wheels 10 In. Front Casters 3.5 In.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SAFETY INFORMATION ...........................1 GROUNDING INSTRUCTIONS ........................1 USING EXTENSION CORDS........................2 LIFTING AND TRANSPORTATION ......................2 PREPARATION ..............................2 SQUEEGEE ASSEMBLY .............................3 SQUEEGEE HEAD REMOVAL AND INSTALLATION ................3 SQUEEGEE BLADE REPLACEMENT .......................3 SQUEEGEE LIFT ............................4 MACHINE DRAINING ............................5 COVER ASSEMBLY .............................6 DRY FILTER ................................7 WIRING DIAGRAM.............................7 MAINTENANCE ..............................8... -
Page 4: Safety Information
SAFETY INFORMATION SAVE THESE INSTRUCTIONS This machine is intended for commercial use. When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING: To reduce the risk of fire, electrical shock, or injury: •... -
Page 5: Using Extension Cords
USING EXTENSION CORDS The machine comes standard with a 50 foot, 16 gauge, 3 conductor cord (50’ 16/3 AWG). Do not use an extension cord in conjunction with the cord provided with the machine. Replacement cords must meet or exceed the specification of the original cord. -
Page 6: Squeegee Assembly
SQUEEGEE ASSEMBLY SQUEEGEE HEAD REMOVAL AND INSTALLATION Use the two black center knobs (rotate counter-clockwise to loosen, rotate clockwise to tighten) to remove and install the squeegee assembly from the machine. SQUEEGEE BLADE REPLACEMENT NOTE: The Squeegee Blades can be used twice by flipping them over to use the previously un-used edge. Installation is the reverse of installation. -
Page 7: Squeegee Lift
SQUEEGEE LIFT • Move the foot lever forward and allow the Squeegee Assembly to lower to the working position. • Press the foot lever down and back to lock the Squeegee Assembly to the upper position. RETURN TO TABLE OF - 4 - CONTENTS... -
Page 8: Machine Draining
MACHINE DRAINING NOTE: The vacuum must be turned off prior to draining the machine. Hose Drain: 1. Back the machine up to the drain. 2. Lift the drain hose from the holster. 3. Remove the drain cap. 4. Lay the hose into the drain. 5. -
Page 9: Cover Assembly
COVER ASSEMBLY Open: To open the cover assembly, release the latch on the front of the machine and lift the cover backwards until it stops. Close: Lower the cover, verifying it is properly seated on the Tank. Secure the latch to the catch on the Tank. Removal: 1. -
Page 10: Dry Filter
DRY FILTER The optional dry filter is installed over the ball float. The dry filter must be removed for wet recovery. NOTE: Once the mount bracket is installed, it does not need to be removed. Installation: 1. Use the (2) screws and lock washers to install the mount bracket as shown. -
Page 11: Maintenance
MAINTENANCE NOTE: Read all safety instructions prior to performing maintenance. WARNING: Always unplug the cord from the power source prior to performing any service, maintenance, or inspection of the machine. 1. After each use: • Inspect cords, switched, casters, and wheels for wear or damage. •... -
Page 12: Parts Diagrams
PARTS DIAGRAMS COVER ASSEMBLY ITEM QTY PART NUMBER DESCRIPTION 692301 COVER TANK WDV 692302 COVER MOTOR VACUUM 962263 SCREW, BUTT, SOCK, .25-20X.62, SS BO 695201 MOTOR VACUUM 120VAC 603473 GASKET 198395 696101 PLATE MTG MOTOR VACUUM 911089 SWITCH, ROCKER, 20A 125 VAC 693301 FOAM NOISE MOTOR COOLING 693302... - Page 13 PARTS DIAGRAMS COVER ASSEMBLY RETURN TO TABLE OF - 10 - CONTENTS...
-
Page 14: Tank Assembly
PARTS DIAGRAMS TANK ASSEMBLY Prior To Serial Number: 120540 ITEM QTY PART NUMBER DESCRIPTION 698601 TANK RECOVERY WDV 694101 HOSE DRAIN WDV WITH CAP 692002 CLAMP HOSE PLASTIC 1.69-1.81 DIA 696801 PLUG DRAIN HOLE 2 INCH W189D SCREW, HEX, 1/4-20 X .75, SS, PATCH 980002 WASHER, LOCK, SPLIT, .25 W104D... - Page 15 PARTS DIAGRAMS TANK ASSEMBLY Prior To Serial Number: 120540 RETURN TO TABLE OF - 12 - CONTENTS...
- Page 16 PARTS DIAGRAMS TANK ASSEMBLY After Serial Number: 120540 ITEM QTY PART NUMBER DESCRIPTION 698601 TANK RECOVERY WDV 694101 HOSE DRAIN WDV WITH CAP 692002 CLAMP HOSE PLASTIC 1.69-1.81 DIA 696801 PLUG DRAIN HOLE 2 INCH W189D SCREW, HEX, 1/4-20 X .75, SS, PATCH 980002 WASHER, LOCK, SPLIT, .25 W104D...
- Page 17 PARTS DIAGRAMS TANK ASSEMBLY After Serial Number: 120540 RETURN TO TABLE OF - 14 - CONTENTS...
-
Page 18: Squeegee Assembly
PARTS DIAGRAMS SQUEEGEE ASSEMBLY ITEM QTY PART NUMBER DESCRIPTION 693202 FRAME SQUEEGEE WDV 697201 RETAINER BLADE SQUEEGEE 690701 BLADE SQUEEGEE 2-EDGE WDV 694102 HOSE SQUEEGEE WDV 695001 KNOB RETENTION SQUEEGEE 695005 KNOB RETENTION BLADE BLUE 920701 NUT ACORN .25-20 1-PIECE BLK 962478 SCREW 14-20X2.25 HEX ZINC FULL THRD 920011... -
Page 19: Squeegee Link Assembly
PARTS DIAGRAMS SQUEEGEE LINK ASSEMBLY ITEM PART NUMBER DESCRIPTION 693201 FRAME LIFT SQUEEGEE 690802 BRACKET LIFT SQUEEGEE 962238 SCREW SHLDR .38”DIA. X .25”L X .31-18 691101 BUSHING SPLIT .38 INCH 920036 NUT, NYLOCK, 5/16-18, SS 699702 WHEEL 2 INCH DIA .31 ID 920011 NUT, NYLOCK, 1/4-20, ZINC 962290... -
Page 20: Optional Accessories Kit
OPTIONAL ACCESSORIES KIT ITEM PART NUMBER DESCRIPTION 695004 KIT, ACCESSORIES 980002 LOCK WASHER W169D 1/4-20 HEX CAP SCREW 690801 BRACKET, FILTER RETAINER 693304 FILTER ELEMENT (W/ UPPER & LWR SEALS) 691501 CAP, FILTER RETAINER 920700 NUT, WING .38-16 TOOL, HARD FLOOR TOOL, UPHOLSTERY TOOL SQUEEGEE BRUSH FLOOR... - Page 21 OPTIONAL ACCESSORIES KIT RETURN TO TABLE OF - 18 - CONTENTS...
-
Page 22: Warranty
Provider with a written factory service agreement with shipping and delivery charges prepaid. If unable to locate a Authorized Factory Service Provider, you may contact Pacific Floorcare at the address listed herein for the location of the nearest service provider or agent for other instructions pertaining to your concern. - Page 23 REVISION REVISION LOG 2020.7.29 DOCUMENTED NEW WHEELS, ADDED PGS. 13-14 RETURN TO TABLE OF - 20 - CONTENTS...
- Page 24 www.pacificfloorcare.com...
Need help?
Do you have a question about the WDV-18 and is the answer not in the manual?
Questions and answers