Summary of Contents for TAKEBISHI MITSUBISHI ELECTRIC MELSEC iQ-R Series
- Page 1 MELSEC iQ-R MES Interface Module Option Driver User's Manual -SW1SFD-RMESOPRC-B -SW1SFD-RMESOPSM-B -SW1SFD-RMESOPOM-B This product was jointly developed by Mitsubishi and Takebishi Corporation.
-
Page 3: Safety Precautions
SAFETY PRECAUTIONS (Read these precautions before using this product.) Before using this product, please read this manual and the relevant manuals carefully and pay full attention to safety to handle the product correctly. The precautions given in this manual are concerned with this product only. For the safety precautions for the programmable controller system, refer to the user's manual for the CPU module used. - Page 4 [Startup and Maintenance Precautions] CAUTION ● The online operations performed from a personal computer to a running CPU module (program change while a CPU module is in RUN state, operating status change such as RUN-STOP switching, and remote control operation) have to be executed after the manual has been carefully read and the safety has been ensured.
-
Page 5: Conditions Of Use For The Product
CONDITIONS OF USE FOR THE PRODUCT (1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions; i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or serious accident; ii) where the backup and fail-safe function are systematically or automatically provided outside of the PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT. - Page 6 INTRODUCTION Thank you for purchasing a MELSEC iQ-R MES interface module option driver. This manual describes the specifications, procedures before operation, and troubleshooting of this product. Before using this product, please read this manual and the relevant manuals carefully, and develop familiarity with the functions and performance of this product to handle correctly.
- Page 7 CONTENTS SAFETY PRECAUTIONS ..............1 CONDITIONS OF USE FOR THE PRODUCT .
- Page 8 Accessible devices ............... 34 Access units .
-
Page 9: Relevant Manuals
RELEVANT MANUALS Manual name [manual number] Description Available form MELSEC iQ-R MES Interface Module Option Driver Specifications, procedure before operation, and troubleshooting of an MES Print book User's Manual interface module option driver e-Manual [SH-082186ENG] (this manual) MELSEC iQ-R MES Interface Module User's Manual Specifications, procedure before operation, wiring, and operation examples of Print book (Startup) - Page 10 TERMS Unless otherwise specified, this manual uses the following terms. Term Description Configuration personal computer A personal computer to set various settings required for operating an MES interface module. This computer can be shared with a server. An abbreviation for Manufacturing Execution Systems. A system for controlling and monitoring the plant status in real time to optimize production activities.
-
Page 11: Software Configuration
OPTION DRIVER An option driver is software to add a function for connecting to a device that is not supported as standard to an MES interface module. The following types of option drivers are available. By installing each option driver, an MES interface module can be connected to each corresponding option driver-supported device. - Page 12 MEMO 1 OPTION DRIVER 1.1 Software Configuration...
-
Page 13: Common Specifications
COMMON SPECIFICATIONS This chapter explains the common specifications of an option driver. For the access specifications of each option driver, refer to the corresponding one of the following: Page 29 Rockwell Connection, Page 33 Siemens Connection, Page 39 Omron Connection Item Specification Access target device... - Page 14 MEMO 2 COMMON SPECIFICATIONS...
-
Page 15: Procedure Before Operation
PROCEDURE BEFORE OPERATION This chapter shows the procedure before operation of an option driver. To use an option driver, license certification using a license file is required. Operating procedure Acquire a license file. Page 14 Acquiring a License File Enable the option driver setting. For the method of enabling, refer to the following: MELSEC iQ-R MES Interface Module Option Driver Installation Instructions Install an option driver body on an MES interface module. - Page 16 Acquiring a License File This section shows the procedure for acquiring a license file. Note that it takes approximately a week to acquire a license file. When using an option driver before acquiring a license file, temporary authentication of the option driver is required. Page 27 Enabling Temporary Authentication Operating procedure Check the entitlement ID shown in the Entitlement ID Notification.
-
Page 17: Installation And Uninstallation
INSTALLATION AND UNINSTALLATION This chapter shows the methods for installing and uninstalling an option driver. Considerations for installation and uninstallation ■Option driver body • Up to three option driver bodies can be installed on an MES interface module. • An option driver body cannot be installed by overwriting an existing one. To upgrade the version, uninstall an installed option driver body then restart an MES interface module, and install a new version of the option driver body. -
Page 18: Installation Procedures
Installation Procedures Option driver body The following shows the procedures for installing an option driver body on an MES interface module. For checking the version of an installed option driver body, refer to the following: Page 22 Option driver body Using MES Interface Function Configuration Tool The following shows the installation procedure using MES Interface Function Configuration Tool. - Page 19 Using an SD memory card The following shows the installation procedure using an SD memory card. Operating procedure Turn the power of a programmable controller OFF. Copy the following folder in each product DVD-ROM to the OPD folder in an SD memory card used for an MES interface module.
- Page 20 Tool add-in The following shows the procedure for adding a tool add-in to MES Interface Function Configuration Tool. For checking the version of an added tool add-in, refer to the following: Page 22 Tool add-in Operating procedure Select [Option] [Management of Add-ins] in MES Interface Function Configuration Tool. Click the [Add] button.
-
Page 21: Uninstallation Procedures
Uninstallation Procedures Option driver body The following shows the procedures for uninstalling an option driver body from an MES interface module. Using MES Interface Function Configuration Tool The following shows the uninstallation procedure using MES Interface Function Configuration Tool. Operating procedure Select [Online] ... -
Page 22: Using An Sd Memory Card
Using an SD memory card The following shows the uninstallation procedure using an SD memory card. Operating procedure Turn the power of a programmable controller OFF. Delete any of the following folders in an SD memory card used for an MES interface module. Option driver Folder Rockwell Connection... - Page 23 Tool add-in The following shows the procedure for deleting a tool add-in from MES Interface Function Configuration Tool. Operating procedure Select [Option] [Management of Add-ins] in MES Interface Function Configuration Tool. Select a target tool add-in in "Tool Add-in List". Click the [Delete] button.
-
Page 24: Checking The Version
Checking the Version This section shows the procedures for checking the version of an option driver. Option driver body The following shows the procedure for checking the version of an option driver body. Operating procedure Select [Online] [Manage MES Interface Module]. Select the [Option Driver Management] tab. -
Page 25: License Management
LICENSE MANAGEMENT This chapter shows the methods for managing licenses. For checking the certification status of a license, refer to the following: Page 28 Checking the Certification Status of a License Registering a License File This section shows the methods for registering a license file. Considerations •... - Page 26 Using an SD memory card The following shows the registration procedure using an SD memory card. Operating procedure Turn the power of a programmable controller OFF. Change the name of a license file saved in the following section to 'lic.v2c'. Page 14 Acquiring a License File Copy the license file to any of the following folders in an SD memory card used for an MES interface module.
- Page 27 Deleting a License File This section shows the methods for deleting a license file. Certification of a license fails in the following cases. If it fails, delete an invalid license file and register a valid one. • An incorrect license file is registered. •...
- Page 28 Using an SD memory card The following shows the deletion procedure using an SD memory card. Operating procedure Turn the power of a programmable controller OFF. Delete any of the following folders in an SD memory card used for an MES interface module. Option driver Folder Rockwell Connection...
- Page 29 Enabling Temporary Authentication This section shows the method for enabling the temporary authentication of an option driver. By enabling the temporary authentication, an option driver can be used before acquiring a license file. Operating procedure Select [Online] [Manage MES Interface Module] in MES Interface Function Configuration Tool. Select a target option driver body in "Option Driver List"...
- Page 30 Checking the Certification Status of a License This section shows the two methods for checking the certification status of a license. Checking with the LED status The certification status can be checked with 'LICENSE LED' of an MES interface module. LED status Description Certification succeeded (succeeded in certification of all the licenses of option drivers used for settings of a running MES...
- Page 31 Rockwell Connection This chapter explains Rockwell Connection. Access Specifications This section shows the access specifications of Rockwell Connection. Accessible devices (products) Series Model name Ethernet communication module ControlLogix 1756 1756-ENBT, 1756-EN2T(/C, /T) CompactLogix 1769-L32E, 1769-L35E 1768 1768-ENBT FlexLogix 1794 1788-ENBT DriveLogix 5720, 5730...
-
Page 32: Parameter Settings
Parameter Settings This section shows the parameter settings for Rockwell Connection in MES Interface Function Configuration Tool. For details on MES Interface Function Configuration Tool, refer to the following: MELSEC iQ-R MES Interface Module User's Manual (Application) Access target device setting The following shows the setting of an access target device accessed from an MES interface module. -
Page 33: Device Tag Setting
Device tag setting The following shows the setting of a device tag accessed from an MES interface module. A screen for setting device tags is not provided in Rockwell Connection. Enter devices set in a Rockwell PLC directly in the "Device Tag Setting" screen. Set the following data types for "Data Type"... - Page 34 Checking Methods for Error Descriptions This section shows the checking methods for error descriptions of Rockwell Connection. Checking method Details System monitor of an engineering tool Error codes can be checked by the system monitor of an engineering tool. For details, refer to the following: MELSEC iQ-R MES Interface Module User's Manual (Application) MES Interface Function Configuration Tool Error codes...
- Page 35 Siemens Connection This chapter explains Siemens Connection. Access Specifications This section shows the access specifications of Siemens Connection. Accessible devices (products) Series Type Model name Ethernet communication module SIMATIC S7 S7-300 CPU 312/314/315-2 (PN/DP), CPU317-2 (PN/DP) CP343-1 S7-400 CPU 412-1/2, CPU 417-4, CPU414-2/3 (PN/DP), CP443-1 CPU416-2/3 (PN/DP), CPU412-3H, CPU414 /417-4H S7-1200...
-
Page 36: Accessible Devices
Accessible devices Device (register) Name Address range Basic data type Memory (Flag Memory) 0 to 65535 BOOLEAN, INT16, UINT16, INT32, UINT32, FLOAT, DOUBLE, STRING, Input WSTRING Output Peripheral Input Peripheral Output Data Block Counter UINT16 Timer *1 Read-only *2 Set it by combining a data block number and an address. *3 Treated as BCD type data in Siemens PLCs. - Page 37 Parameter Settings This section shows the parameter settings for Siemens Connection in MES Interface Function Configuration Tool. For details on MES Interface Function Configuration Tool, refer to the following: MELSEC iQ-R MES Interface Module User's Manual (Application) Access target device setting The following shows the setting of an access target device accessed from an MES interface module.
- Page 38 Precautions The following items cannot be set. • Multiple CPU Setting • Co-Existence Network Route setting • Global Label/Common Device Comment Settings (optional) 7 Siemens Connection 7.2 Parameter Settings...
- Page 39 Device tag setting The following shows the setting of a device tag accessed from an MES interface module. Window Click "Device Tag Settings" in the edit item tree. Click the [Edit] button in the "Device Tag Setting List" screen. Click the [...] button of "Device Memory (Start)" in the "Device Tag Setting" screen. Displayed items Item Description...
- Page 40 Checking Methods for Error Descriptions The checking methods for error descriptions of Siemens Connection are same as those shown in the following: Page 32 Checking Methods for Error Descriptions 7 Siemens Connection 7.3 Checking Methods for Error Descriptions...
-
Page 41: Omron Connection
Omron Connection This chapter explains Omron Connection. Access Specifications This section shows the access specifications of Omron Connection. Accessible devices (products) Type Model name Ethernet communication module SYSMAC-CJ CJ1G, CJ1H, CJ1M, CJ2H, CJ2M CJ1W-ETN21, CJ1W-ETN11, CJ1W-EIP21 SYSMAC-CS CS1G, CS1H, CS1D CS1D-ETN21D, CS1W-ETN21, CS1W-ETN11, CS1W-ETN01, CS1W-EIP21 SYSMAC-CP... - Page 42 Accessible devices Device Name Address range Data type (register) CJ/JS/CP Timer Contact 0 to 4095 0 to 1023 BOOLEAN Counter Contact Channel I/O 0 to 6143 0 to 2555 BOOLEAN, INT16, UINT16, INT32, UINT32, FLOAT, DOUBLE, STRING, Internal Auxiliary Relay 0 to 511 ...
- Page 43 Parameter Settings This section shows the parameter settings for Omron Connection in MES Interface Function Configuration Tool. For details on MES Interface Function Configuration Tool, refer to the following: MELSEC iQ-R MES Interface Module User's Manual (Application) Access target device setting The following shows the setting of an access target device accessed from an MES interface module.
- Page 44 Precautions The following items cannot be set. • Multiple CPU Setting • Co-Existence Network Route setting • Global Label/Common Device Comment Settings (optional) 8 Omron Connection 8.2 Parameter Settings...
- Page 45 Device tag setting The following shows the setting of a device tag accessed from an MES interface module. Window Click "Device Tag Settings" in the edit item tree. Click the [Edit] button in the "Device Tag Setting List" screen. Click the [...] button of "Device Memory (Start)" in the "Device Tag Setting" screen. Displayed items Item Description...
- Page 46 Checking Methods for Error Descriptions The checking methods for error descriptions of Omron Connection are same as those shown in the following: Page 32 Checking Methods for Error Descriptions 8 Omron Connection 8.3 Checking Methods for Error Descriptions...
-
Page 47: Error Code List
APPENDIX Appendix 1 Error Code List This section shows the error code list for an option driver. For error codes other than those shown in this section, refer to the following: MELSEC iQ-R MES Interface Module User's Manual (Application) Error code Error name Error description Corrective action... - Page 48 List of error codes displayed in detailed information 3 The following table shows the list of error codes displayed in detailed information 3 and their respective causes and corrective actions. Error code Error cause Corrective action 0001H A specified option driver is not loaded. •...
-
Page 49: Buffer Memory List
Appendix 2 Buffer Memory This section shows the buffer memories in which information on an option driver is stored. • Un\1038 to 1085 For the buffer memories other than the above, refer to the following: MELSEC iQ-R MES Interface Module User's Manual (Application) Buffer memory list The following table shows the buffer memories in which information on an option driver is stored. -
Page 50: Buffer Memory Details
Buffer memory details The following shows the details of the buffer memories in which information on an option driver is stored. Option driver 1 detailed information (Un\G1038 to 1053) Detailed information on option driver 1 is displayed. ■Version information (Un\G1038 to 1039) •... - Page 51 Appendix 3 Saving a Project to a CSV File This section shows the specifications when saving a project in which an option driver is set to a CSV file. For the contents other than those of items shown in this section and the input/output specifications of a CSV file, refer to the following: MELSEC iQ-R MES Interface Module User's Manual (Application) ADDIN folder...
- Page 52 Column title Content CSV format version resourceNo Resource number resourceNoOther Resource number (other) cpuRackNo CPU rack number slotNo Slot number maxMessageLength Maximum message length readBlockSize Number of read blocks writeBlockSize Number of written blocks delay Send delay timeout Timeout retry Number of retries •...
- Page 53 Column title Content CSV format version regType Register type blockNo Block number regAddress I/O address s5TimerType S5 timer type bitpos Bit position dataType Data type strSize String size arySize Array size aryType Array type • Omron Connection Column title Content CSV format version acssryKey Accessory key...
- Page 54 Setting information file Information on a set option driver is output to the following items in setting information files. TARGET_DEVICE.CSV Column title Content Setting value Description of setting value DEVICE TYPE Device type ADDIN000 Option driver-supported device *1 An integer indicating an option driver ID. It differs depending on an option driver. Rockwell Connection: 001 Siemens Connection: 002 Omron Connection: 003...
- Page 55 Appendix 4 Checking the Availability of an Option Driver This section shows the procedures for checking the availability of an option driver. Option driver body The following shows the procedure for checking the availability of an option driver body. Operating procedure Select [Online] ...
- Page 56 Appendix 5 System Recovery When a Failure Occurs in a Module License certification of an option driver can be performed only to an MES interface module the product information of which was entered when acquiring a license file. Therefore, if using an SD memory card in which the license file is saved for another MES interface module after a failure occurs, license certification will fail.
- Page 57 INDEX ....48 Buffer memory details ..... . . 47 Buffer memory list .
- Page 58 MEMO...
- Page 59 REVISIONS *The manual number is given on the bottom left of the back cover. Revision date *Manual number Description October 2019 SH(NA)-082186ENG-A First edition Japanese manual number: SH-082185-A This manual confers no industrial property rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual.
- Page 60 TRADEMARKS Microsoft, Windows, Windows Vista, Windows XP, and Excel are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. The company names, system names and product names mentioned in this manual are either registered trademarks or trademarks of their respective companies.
- Page 62 SH(NA)-082186ENG-A(1910)KWIX MODEL: SW1SFD-RMESOP-U-E MODEL CODE: 13JX1D HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN NAGOYA WORKS : 1-14 , YADA-MINAMI 5-CHOME , HIGASHI-KU, NAGOYA , JAPAN When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission.