Advertisement
JI-112C – Video verification IP camera BULLET
7. Fix the camera base to the mounting base using four metric screws
and a Torx key. Mind the correct position of the camera
to the mounting base.
8. Perform camera registration (see the chapter:
) to obtain access to preview and align the camera
to a server
in the required direction, allowed in three axes, see figure 3.
Installation of camera without a mounting base:
When the camera is going to be installed at a place where
all the connecting cables are protected against tampering (for
example a lowered ceiling, drywall ceilings and wall partitions etc.),
then the camera can be mounted on a flat surface directly and
cables with connectors put through the prepared hole.
Warning: A waterproof sheath (cover) has to be put on the cable
before pressing the RJ-45 data connector.
Figure 6: Assembling the waterproof sheath of the LAN connector;
1 – camera connector (bayonet closure); 2 – O-ring; 3 – RJ plug/connector;
4 – waterproof sheath; 5 – sealing sleeve; 6 – locking nut; 7 - cable
Power
Permanent powering of the camera is required and can be realized
in two ways:
a) Powering via data cable called PoE (Power over Ethernet),
the switch or router has to support it. Alternatively a suitable PoE
injector can be used. The voltage (48 V) is standardized
by the IEEE 802.3af network norm. This has a big advantage;
the camera is powered directly via the data cable.
b) An external 12 V/500 mA power supply connected to the 2.1 mm
connector of a camera. This way requires an extra cable
for powering separately to the data cable. The advantage is that
the camera can be backed up by an appropriate backup power
supply.
Figure 7: Camera connectors;
1 – External power connector 12 V DC; 2 – LAN connector
Caution: When a backup power supply is used to power the camera
when a mains power outage occurs, it is also necessary to have all
devices providing internet connection and data transfer to Internet
backed up (routers, switches, modems, wireless transmitters, etc.).
Camera connection to LAN network
Video data transfer is based on continuous communication with
the Jablotron server to which data is sent. Set up the DHCP
function to be used in the local network. Communication ports
between the camera and the JABLOTRON cloud are 443, 8883
and ports range from 8000 to 8500. Unless your network is pre-set
with special restriction, it is usually not necessary to modify any
parameters of the firewall or router.
Caution: The camera is not physically connected to the JABLOTRON
100 system, it doesn´t occupy any positions. Power from the alarm
system is not required and the camera status is not monitored
by the control panel.
Registration to a server
Registration can be performed from the web or a smart
application for cell phones by entering the unique camera MAC
address on the label stuck on camera body or on its box. It can also
be scanned by QR code. Every camera can be registered to only
one JALOTRON 100 system. Camera can be registered within 30
minutes after it was powered. When this time frame expires then
registration can be repeated by voltage restart.
JI-112C – Video verification IP camera BULLET
Registration procedure:
1.
Connect the power to the camera (initialisation takes approx. 1 minute)
2.
Log in to the MyCOMPANY application and open the „INSTALLATION
Registration
MANAGEMENT" module.
3.
Select the installation to which you want to register the camera.
4.
Go to the CAMERAS tab and click onto REGISTER A CAMERA
5.
Fill in or scan the MAC address of the camera and enter the name
which will be displayed in MyJABLOTRON and click onto
"REGISTER".
6.
When registration is confirmed in MyCOMPANY, for possible
adjustment in the following 24 hours the installer can watch a live
preview from this camera. After that a permanent livestreaming
is available in the MyJABLOTRON application for the end user only.
Caution: Because of security reasons it is impossible to record
data to another storage system (like local NVR, etc.). Access
to the camera's internal settings is not possible.
MyCOMPANY programmable options:
Click the configuration symbol of a specific camera in the list
of available cameras.
There the following parameters are to be set:
The Quality of videostreaming option changes the image quality.
By clicking the button a camera setting change is performed.
The parameter has a big influence on the recorded video quality and
the amount of data transfer to the server (uploading).
Activation of video sequence for a section – by checking those
options you pre-set from which sections and for what type of events
video sequences are stored.
Connect to ARC – this option sends a request for connection
to a monitoring agency ARC.
Deactivate the camera – the button erases the camera and
all the recorded data from the JABLOTRON Cloud secure server.
The option can only be performed by the installation company which
registered the camera. The camera cannot be erased with activated
monitoring by an ARC.
Save configuration – send pre-set data to the cloud.
Up to twenty IP cameras can be used for one JA-100 system.
Always depending on number of cameras and their settings check
whether there is available corresponding data transfer from
the premises to the Internet (upload).
Warning:
to the camera's ability to acquire video recordings, the camera has
to be used within the limits given by national laws or norms,
especially laws about the protection of personal privacy and
credentials.
According to these regulations users have an obligation to ensure
the approval of persons in range of the camera during
the acquisition of video recordings or the obligation to indicate
the image capture area by informative signs.
The manufacturer recommends that users should be aware
of the legal obligations applicable to the operation of camera
systems before installation and use of the camera.
Digital IP camera with prepared connectors on a 45 cm cable
Mounting base (diameter 105 mm, height 37 mm)
Waterproof sheath for LAN connector with seal
Drilling template as a sticker for making four holes for camera
installation on a wall
Torx key T20
4x dowels (6 mm) with self-tapping screws (3 mm x 25 mm)
to fix the camera or mounting base on a wall
4x metric screws (4 mm x 20 mm) to fix camera onto
the mounting base
Sticker with a warning that the area is protected / monitored
by a camera system
2 / 3
Recommendations
The
producer
strictly
warns
Included items list
users
that
due
MZZ507302
Advertisement
