Advertisement
Quick Links
1．功能簡介
- 6 Phoenix Input Channels with gold plated XLRs and balanced
Line Inputs.
- 5 RCA Input Channels,Mix,Tuner,Tape,CD and Aux Intputs.
- Ultra-low noise discrete Mic Preamps with +27V Phantom
Power.
- Warm , natural 2-band EQ on each channels.
- Peak LEDs
- 2 Phoenix Outputs,Master and Subgroup Outputs.
- 3 RCA Outputs, Master and Record and Return Outputs.
- REMOTE-9pin Sub-D connection for remote control.
As an option:AP 232 for RS 232 interface (PCB),refer to chapter
"11. AP 232 Retrofit Kit"
- Performance and excellent noise figures.
- Rugged construction ensures long life even under the most
demanding conditions.
02_1
Advertisement
Related Manuals for Beyerdynamic MIX 10 NG
Summary of Contents for Beyerdynamic MIX 10 NG
- Page 1 1．功能簡介 - 6 Phoenix Input Channels with gold plated XLRs and balanced Line Inputs. - 5 RCA Input Channels,Mix,Tuner,Tape,CD and Aux Intputs. - Ultra-low noise discrete Mic Preamps with +27V Phantom Power. - Warm , natural 2-band EQ on each channels. - Peak LEDs - 2 Phoenix Outputs,Master and Subgroup Outputs.
- Page 2 OUTPUT AP 232 LEFT RIGHT JUMP CH7~10 2-BAND EQ JUMP MASTER RIGHT OUTPUT RIGHT Titel BLOCK DIAGRAM MIX 10 NG Size Model No: Revision MIX 10 NG REV1.20 11-Apr-2006 Date: Sheet 1 of File: MIX10 MAP.Sch Drawn By: KENNY HO.
- Page 3 10_1...
-
Page 4: Safety Related Symbols
SAFETY RELATED SYMBOLS Fuse To prevent fire and damage to the product, use only the recommended fuse type as indicated in this CAUTION manual. Do not short-circuit the fuse holder. Before RISK OF ELECTRIC SHOCK DO NOT OPEN replacing the fuse, make sure that the product is OFF and disconnected from the AC outlet. - Page 5 10_3...
- Page 6 Therefore, do not install the amplifier near swimming pools, spas, in a wet basement, or in any other excessively humid environments. Do not install or use the MIX 10 NG near sources of high excessive heat, such as radiators, heat registers, flood lamps, spotlights, stoves, or other heat generating appliances.
-
Page 7: Chapter "4.1.1 Priority Switching")
"6. Configuration of the Printed Circuit Board". when the MIX 10 NG is equipped with the AP 232 retrofit kit, there are more adjustments of the ducking function possible (refer to chapter"9. AP 232 Retrofit Kit"). - Page 8 When the MIX 10 NG is switched on, the line input 1"Tuner" is always selected (the source selection switch (3) is still working a few seconds after the MIX 10 NG is switched off until the storage capacitor is discharged).
- Page 9 6.Configuration of the Printed Circuit Board (11) (10) (1)Mic 1~Mic 6 send signal to master L+R Bus (2)Mic 1~Mic 6 send signal to Sub L+R Bus (3)MIX INP send signal to Master L+R Bus (L: J25, R:J27) (4)MIX INP send signal to Sub L+R Bus (L: J26, R: J28) (5)Mic 1~Mic 6, MIX INP send signal to Master L+R Bus (L: J10, R: J16) (6)Line channel send signal to Master L+R Bus (L:J30, R:J32) (7)Line channel send signal to Sub L+R Bus (L: J29, R: J31)
- Page 10 CUE, Crestron, AMX) use the AP 232 PCB. Refer also to chapter"9. AP 232 Retrofit Kit". 9. AP 232 Retrofit Kit For an operation and configuration of the MIX 10 NG via a PC or media control system, the MIX 10 NG has to be equipped with the AP 232 retrofit kit.
- Page 11 The LEDs below the fields indicate the selected line source of the MIX 10 NG. Also changes at the MIX 10 NG itself are indicated. For configurations of the switch-on status refers to chapter "9.4.1 Start". 9.3.3 Stereo Using the slide control in the "Stereo" operating field you can adjust the volume of the overall master.
- Page 12 (refer to chapter "9.4.3 Fading"). For configurations of the switch-on status refers to chapter "9.4.1 Start". 9.4 Configuration You enter the configuration menu by selecting the "Configuration" command in the "MIX 10 NG" menu. You can carry out the following adjustments. 9.4.1 Start In the "Start"...
- Page 13 If the MIX 10 NG has recognized errors, they are shown in the "error messages" field.In "reset MIX 10 NG" operating field the user can carry out a reset of the MIX 10 NG. When the reset is done with the option "with user parameters", the adjustments of the MIX 10 NG are kept.
- Page 14 Pin 3 = Rx Pin 5 = GND The data exchange between the MIX 10 NG and the control is done via two-byte messages. The first byte ("ID") is always above 7Fhex, the second byte ("value") is always below 80hex.
- Page 15 Sent Messages The following messages are sent from the MIX 10 NG: An acknowledged message is directly sent from the MIX 10 NG after having received a request, except the sending of acknowledged messages has been disabled or an error occurs.
- Page 16 An error message is sent instead of an acknowledged message when the request is not correct instead of a status message when the status was recognized as incorrect when the MIX 10 NG has recognized an error. 10_14...
- Page 17 (12 + 13) and the line master at the right output (12 + 13) in conjunction with the AP 232 retrofit kit. The MIX 10 NG is wired mono for the line master.
- Page 18 (H × W × D / 44 × 483 × 163) Dimensions..........19 /1 HU Weight............4Kg MIX 10 NG 10-channel-stereo mixing system with AP232 retrofit kit (115V)..Order # 483.850 MIX 10 NG 10-channel-stereo mixing system with AP232 retrofit kit (230V)..Order # 483.842 10_16...
- Page 19 10_17...
- Page 20 12_1...
- Page 21 12_2...
- Page 22 12_3...