Advertisement
Quick Links
Billy Oh Rosette Green House – Assembly Hints and Tips
Please refer to all safety notices in the greenhouse manual before assembling any of the sections
TOP TIPS
1. These instructions are generic for all models. Part numbers vary, please use this product in
accordance with your supplied instruction manual.
2. Please check you have the correct instructions. All parts should be labelled as follows:
Part A for the 12 x 8 greenhouse, Part B for the 10 x 8 greenhouse,
Part C for the 7.4 x 7.4 greenhouse, Part D for the 8 x 6 greenhouse.
3. To ensure the base is level and square, the use of a spirit level is essential and diagonal
corner measurements must be taken and accurately correspond. Failure to achieve this will
result in the greenhouse frame being out of line and prevent accurate positioning of the
glazing panels.
4. When satisfied with the base section the frame should be erected with constant use of the
spirit level even though adjustments will be necessary as the work progresses.
WARNING
Advertisement
Summary of Contents for Billyoh Rosette
- Page 1 Billy Oh Rosette Green House – Assembly Hints and Tips WARNING Please refer to all safety notices in the greenhouse manual before assembling any of the sections TOP TIPS 1. These instructions are generic for all models. Part numbers vary, please use this product in accordance with your supplied instruction manual.
- Page 2 It is not guaranteed to prevent damage occurring during adverse weather but merely a suggestion). (see Additional Customer Tips section) 12. To summarise, the erection of the BillyOh Rosette Greenhouse may in the beginning appear a daunting task and the structure deceptively flimsy. However, with patience and perseverance, the end result is worth all efforts and the finished article , remarkably resilient.
-
Page 3: Base Frame Assembly
Base Frame Assembly Loosely insert nut and bolt Fig 1 Assemble the base frame as detailed in the instructions and secure using the bolts as above. Place the nut and bolts into the top sections and secure loosely then lay the next sections on top of the base as per Fig 1. - Page 4 Clips for Uprights Each of the uprights has clips ( Part 35 ) on the inside which need to be used as shown to add additional stability to the uprights. Note how the corner is completed. The photo is taken Inside the greenhouse and we are looking at the Right hand corner.
- Page 5 Door Runner Assembly It is recommended to leave the fitting of the door runner ( Part #22 )until the rest of the greenhouse is complete. As a first stage when building the main green house just place the nut and bolt in place on the left and right side as per the following photo.
- Page 6 Place the remaining top door runner into the groove to complete the door attachment process. Make sure you attach the bottom grooves to the greenhouse base. Once you have the runner in place with the doors, the last job to do is to tighten the two top bolts. Door Runner Corner Assembly At first glance it appears from the instructions that the fitting of the door rail assembly is complicated...
- Page 7 Down Pipe Collector The plastic down pipe connector slides between the gutter and the upright. Tip, you may need to loosen the nut and bolts to assist in this then push the plastic connector in and re-tighten the bolts.
- Page 8 Opening Vent Some greenhouses have one opening vent and the larger units have two. The assembly of them is exactly the same. Assemble the frame of the opening vent as per the instructions. Note the hole in the centre of the bottom section, this is for the opening vent handle. Once the frame is assembled this needs to be slid into the ridge frame of the greenhouse.
- Page 9 Please note that there will be gap at the top of the opening vent. This is normal and as it was designed to aid the opening of the window. View from outside View from Inside...
- Page 10 Tip for opening vent. If the vent falls through once it is installed, undue the nuts slightly on the coss section and move up slightly until the bottom of the opening vent catches the centre cross member to prevent the opening vent from falling through into the greenhouse. Cross Member which can be moved into position once the opening vent has been installed Please make sure the cross member is correctly situated.
- Page 11 Door Frame Assembly – All Models Plastic Runner for TOP of door Frame Cross Member Please note it is advisable to build the door frame starting from the top, place the cross member between the two door frame edges and secure using the plastic runners and the securing screws.
- Page 12 Figure 3 – Rear of Door Figure 4 – Door Front Figure 5 – Bottom of Door Please see figure 6 which shows how door is placed into the upper door frame. Figure 6...
- Page 13 Additional Tips Supplied by our Customers (for information Only) 1. If the greenhouse is sited in an exposed location and/or is exposed to high winds, improvisation for extra protection may be considered. If so the following is recommended: Drill 3 holes in the ridge section central to each of the roof panels. Then drill 3 corresponding holes in both gutters.
Need help?
Do you have a question about the Rosette and is the answer not in the manual?
Questions and answers