Advertisement
Quick Links
Advertisement
Summary of Contents for impulce 2 IT8004 PEC DEC
- Page 1 IT8004 PEC DEC Assembly Instructions...
-
Page 2: Table Of Contents
Table of contents Important Safety Instructions--------------------------------- 1 Exploded View Diagram------------------------------------------ 2 Hardware List-------------------------------------------------- ------ 3 Parts List----------------------------------------------------- ---------- 4 Assembly instructions------------------------------------------ -- 5... -
Page 3: Important Safety Instructions
Important Safety Instructions Before beginning any fitness program, you should obtain a complete physical examination from your physician. When using exercise equip- ment, basic precautions should always be taken, including the following: * Read all instructions before using the PEC DEC These instructions are written to ensure your safety and to protect the unit. -
Page 4: Exploded View Diagram
I 8004 PEC DEC Exploded View Diagram... -
Page 5: Hardware List
Hardware List 1 10 14 0 Millimeters Inches... - Page 6 Hardware List 1 10 14 0 Millimeters Inches...
-
Page 7: Parts List
Parts List Item No. Description Item No. Description MainUpright Bolt Cover Iron Bushing ID 12 Side Frame Right Arm Button Side Cover Left Arm Right Axis Of Rotation Plastic Block Left Axis Of Rotation Decal Weight Numbers Cable Slide Allen Wrenh s=6 Start Up Foot Frame Allen Wrenh s=8 Arm Pad... -
Page 8: Assembly Instructions
Assembly instructions Assembly of the PEC DEC takes professional installers about 2 hours. If this is the first time you have assembled this type of equipment, plan to spend more time. It is strongly recom men ded to assemble the equipment by professional installers. You may find it quicker, safer, easier to assemble this equipment with the help of a friend, as some of components may be large, heavy or awkward to handle alone. - Page 9 Step1 Install the Adj. Foot Plates Align the Adj. Foot Plates(#13)to the Main Upright(#1) and the Side Frame(#2) then secure them by hands.
- Page 10 Step2 Assemble The Frame 1)Attach The Base Cross(#27) And The UpperCross(#26) to the Main Upright(#1),using four Allen Bolts(#72) M10×115 eight Washers(#86) Φ 11× 20×2 Φ four Locknuts(#84) M10 2)Align the Side Frame(#2)To The Base Cross(#27)And The Upper Cross(#26),Then Secure It Using four Allen Bolts(#73) M10×120 eight Washers(#86) Φ...
- Page 11 Step3 Assemble The Weight Plates 1 Insert the two Guide Rods(#24)into the Main Upright (#1). 2)Slide the Weight Rubber Bumper(#68) down onto each Guide Rod(# 3)Carefully begin sliding the Weight Plates one by one in sequence;23,22,21,20 4)Align both top ends of the Guide Rods(#24) to the Main Upright(#1) and secure them using: two Allen Bolts(#74)M10×75 two Washers(#86) 11×...
- Page 12 Step4 Assemble The Arm And The Start Foot Frame 1)Insert The Right Arm (#3)And The Left Arm(#4)To The Side Frame(#2) 2)Insert The Start Up Foot Frame(#8)Into The Side Frame (#2)And Secure It Into Place Using: two Nylon Locknuts(#85) M12 two washers(#87) 13× 20×2 Φ...
- Page 13 Step5 Assemble The Axis Of Rotation 1)Insert two Bearing Clip (#45) To The Side Frame(#2) Then Insert The Right Axis of Rotation (#5) And The Left Axis Of Rotation(#6)to the Side Frame(#2) 2)Align The #5.#6 To Two Gimbal Assy(#15) And Secure IT into Place Using: one Hex Bolts(#81) M12×65 one Hex Bolt(#80)
- Page 14 Step 6 Route The Cable 1)Put the clip tied on the weight pin leash onto the top plate(#19),next connect the cable 1(#16) To the top plate(#20) 2)Route the cable1(#16)up and over the two Pulley(#41), and secure them to the Main Upright(#1),using: Two Allen bolts(#76)M10×45 Two Nylon Locknuts(#84)M10 Four washers(#86)
- Page 15 For step 6...
- Page 16 Step7 Assemble The Pads 1)Attach the Back Pad(#11)To the Side Frame(#2)Using: one Allen Bolt (#94)M10×70 Two Allen Bolt(#75)M10×30 Three Washers(#86) Φ 11× 20×2 Φ 2)Attach the Two Arm Pad(#9) To The Right Arm(#3)And The Left Arm (#4) Using: fout Allen Bolts(#75)M10×30 Four Washers(#86) Φ...
- Page 17 Step8 Assemble The Decal Plates 1)Attach the two Decal Plates (#30,#29) to the Main Upright(#1)Using: fourteen Buttions (#53) 2)Attach the Weight Shroud(#25) to the Main Upright(#1), Using: four Bolt Covers (#51) four Plactic Washers (#50) four screws(#90)M5×10 3)Attach the Plastic Cap (#66) to the Main Upright (#1) using: two screws(#67)M6×15 The front Decal Plate (#29)with the exercise inst-...