Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SIIG AV-GM0213-S1
Summary of Contents for SIIG AV-GM0213-S1
- Page 1 VGA & Audio over CAT5 Repeater with RGB Delay Control P/N: AV-GM0213-S1...
-
Page 2: Table Of Contents
However, like all electronic equipments, the AV-GM0213-S1 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. -
Page 3: Introduction
VGA (WUXGA) to cover the distance up to 330m (1,000ft). Equipped with RJ45 input, local VGA and stereo output, and playing as a repeater, AV-GM0213-S1 can extend A/V signals from VGA and audio CAT-5 extender up to another 300m (1,000ft), and monitor the A/V signals with local display and speaker. -
Page 4: Specifications
SPECIFICATIONS Model Name AV-GM0213-S1 CV-917D CV-917D-TX Technical Repeater CV-917D-RX aka CV-917-TX Video bandwidth 350MHz Video support VESA Transmission WUXGA [1920x1200] — 300m (1,000ft) [CAT5e] Audio support Stereo audio Input video signal 1.2 Volts [peak-to-peak] Equalization Continuous analog control RGB delay control [1] Human body model —... -
Page 5: Panel Descriptions
Power supply 5V 2A DC Power consumption 5 Watts [max] Operation 0~40°C [32~104°F] temperature Storage temperature -20~60°C [-4~140°F] Relative humidity 20~90% RH [no condensation] PANEL DESCRIPTIONS Front Panel Stereo OUT: Connect to an analog audio output S/PDIF OUT: Connect to an S/PDIF digital audio output VGA OUT: VGA output to a local video display System OUT: Plug in a CAT-5/5e/6 cable that needs to be linked to the RJ45 connector of the transmitting unit, such as CV-917D-RX. - Page 6 transmitting unit, such as CV-917D-TX. EQUALIZER: Rotary control for equalization of R, G, B, respectively GAIN: Rotary control for gain control of R, G, B, respectively Rotary control: R=0~2, G=3~5, B=6~7, for de-skew compensation on respective color channel (for RGB delay control) -: Push button for decrease a level of de-skew compensation (for RGB delay control) +: Push button for increase a level of de-skew compensation (for RGB delay control)
-
Page 7: Connection Diagram
CONNECTION DIAGRAM... -
Page 8: Hardware Installation
5. Make sure your CAT-5/5e/6 cable is tightly connected and not loose. 6. Plug in 5V DC power cord to the power jack of AV-GM0213-S1. 7. If a blurred video is seen or even worse on the local display, not displayed at all, try to adjust the EQ and Gain rotary controls to improve the cable skew. -
Page 9: Notice
NOTICE 1. All transmission distances are measured using Belden 1583A CAT-5e 125MHz LAN cable and ASTRODESIGN Video Signal Generator VG-859C & VG-870B. The transmission distance is defined as the distance between the video source and the VGA display. 2. The transmission length is largely affected by the type of LAN cables, the type of video sources, and the type of display. -
Page 10: Warranty
The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the AV-GM0213-S1 features and specifications is subject to change without further notice. - Page 11 April, 2018...
Need help?
Do you have a question about the AV-GM0213-S1 and is the answer not in the manual?
Questions and answers