Advertisement
Quick Links
CABLE OVERBLOWING JUNCTION BOX
OPERATION & MAINTENANCE MANUAL
P/N 89066 for 1.25" SDR
P/N 89067 for 1.50" SDR
P/N 89068 for 2.00" SDR
Copyright 2015 by General Machine Products Co., Inc
All rights reserved. No part of this publication may be copied,
reproduced or transmitted in any form whatsoever without the
General Machine Products Co., Inc
written permission of
.
GMP • 3111 Old Lincoln Hwy • Trevose, PA 19053 • USA
TEL: +1-215-357-5500 • www.gmptools.com
Jan 2017 USA Ver 4
Page 1 of 12
General Machine Products Co., Inc.
Manual P/N 33297
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for GMP 89066
- Page 1 General Machine Products Co., Inc written permission of GMP • 3111 Old Lincoln Hwy • Trevose, PA 19053 • USA TEL: +1-215-357-5500 • www.gmptools.com Jan 2017 USA Ver 4 Page 1 of 12 General Machine Products Co., Inc.
-
Page 2: Table Of Contents
REVISION HISTORY Rev # Date Details Author 05/31/12 Original Issue A Konschak Add Allen Key reference; 01/21/15 Combined 89066 and 89067 in A Konschak same manual 11/30/15 Added 2” SDR A Konschak Updated color code on 01/17/17 A Konschak 33218/33219 CONTENTS 1. -
Page 3: Safety Instructions
This equipment should be used only by per- sonnel who have been given the appropriate training and who are competent to use it. These instructions are to be made available to operators of this equipment at all times. Failure to observe these safety instructions could result in serious personal injury and/or property damage. - Page 4 GENERAL PNEUMATIC SAFETY INSTRUCTIONS The GMP Overblowing Junction Box is used in conjunction with the GMP Fiber Optical Cable Blowing Machine, both are pneumatic devices, they use pressur- ized air to project cable at high velocities. Please observe the following precau- tions when operating the Cable Blowing Machine: - 1.
-
Page 5: General Description
3 cable seal slots, one of which will house the seal to suit the size of the existing cable. The third branch is then connected to a GMP Cable Blowing Machine via a short slave length of innerduct for the installation of the new cable or tube(s). -
Page 6: Specification
3. SPECIFICATIONS Cable Diameter Range: 9 - 20mm The maximum diameter of a new cable for installation is dependent on the diameter of the existing cable and the duct size. Duct Size: 1 1/4" SDR 1 1/2” SDR 2” SDR Installation Viscous Viscous... -
Page 7: Operating Procedures
4. OPERATING PROCEDURE IT IS IMPERATIVE THAT ALL PERSONS USING, OPERATING OR MAINTAINING THE OVERBLOWING CABLE JUNCTION BOX, BLOW- ING MACHINE, POWER PACK AND AIR COMPRESSOR MUST BE FULLY TRAINED, COMPETENT AND AUTHORIZED TO DO SO, THEY MUST ALSO HAVE READ THE ENTIRE OPERATING MANUAL. GENERAL MACHINE PRODUCTS CO., INC. - Page 8 fit the innerduct clamp (A) and tighten the two retaining cap screws (H). Do not over tighten the retaining screws. 10. For installing duct tubes, tube end caps will need to be fit- ted, the duct tubes may also need to be pressurized. 11.
- Page 9 5. MAINTENANCE AND SERVICING The GMP Overblowing Junction Box requires very little mainte- nance or servicing. 1. Always ensure that the unit is clean and free from debris, sludge, dirt, water and lubricant. 2. Ensure that all the retaining screws and lower clamp collet screw threads are clean and free from debris, sludge, dirt, water and lubricant.
-
Page 10: Troubleshooting Guide
6. TROUBLESHOOTING GUIDE CABLE BLOWING MACHINE STOPS SUDDENLY DURING CA- BLE INSTALLATION Maximum hydraulic pressure achieved Obstacle in duct installation Power Pack out of fuel Emergency stop button pressed Damaged lead between Power Pack and blowing machine ... -
Page 11: Recommended Spares List
7. SPARES For spare parts always provide the part number and seri- al number. General Machine Products Co. 3111 Old Lincoln Highway, Trevose PA 19053 USA TEL: +1 215 357 5500 FAX: +1 215 357 6216 E-MAIL: info@GMPtools.com Website: www.GMPtools.com Please give as much information as possible to ensure correct identification and supply of spare parts. - Page 12 GMP • 3111 Old Lincoln Hwy • Trevose, PA 19053 • USA Page 12 of 12 General Machine Products Co., Inc. TEL: +1-215-357-5500 • www.gmptools.com...
Need help?
Do you have a question about the 89066 and is the answer not in the manual?
Questions and answers