ZLINK LD-100 Manual

INTRODUCTION
ZLINK LD-100 is a Z-Wave Plus® cer�fied device with S2 Security and SmartStart.
LD-100 is a member of the Z-Wave family and communicates with other Z-Wave
cer�fied devices in a control network. LD-100 is designed to detect and alert any
water leaks in residen�al or commercial buildings. LD-100 features an audible
alarm in addi�on to a wireless alert to your controller providing early no�fica�on
of water leaks before major damage occurs. For more informa�on on this and
other quality ZLINK Products please visit www.ZLINKProducts.com.
BENEFITS
• Water sensing cable may be placed anywhere where there is a risk of a leak,
horizontal (floor, a�c) or ver�cal (wall, along pipes), providing 3D capability to
sense the leak.
• Senses as li�le as couple of drops of water (0.25ml – 0.5ml)
• Provides hundreds of �mes more coverage vs. tradi�onal single point sensors
that only detect leaks in a very localized area.
• Quickly senses water leaks (every 400msec with micro USB power supply, every
60 sec. with ba�ery) before expensive damage occurs.
• LD-100 reports local temperature once every 60 minutes on ba�ery, when using
micro USB power supply it can be set using configura�on parameter 3.
• Built-in audible buzzer sounds when water is detected.
• Includes 4-foot-long sensing cable that senses water on any part of the cable.
• Water sensing cable extend-able up to 150 feet with available extensions.
• Powered by 3 x AAA ba�eries (not included) or standard 5V micro USB power
supply (not included).
FEATURES
• If water is detected, unit will send a Z-Wave No�fica�on command class
type (Water Alarm V2 0x05), event type (Water Leak Detected V2 0x02)
• Includes wall moun�ng plate
•
Meets IP44 splash proof ra�ng (with ba�ery opera�on)
• Flexible and can be placed anywhere horizontally as well as ver�cally
• Cable is reusable a�er leak is detected and cable dries
• For indoor use only
SETUP
Step 1
Remove the two screws in the rear
panel, slide off the ba�ery cover, and
insert the 3 AAA ba�eries. Or remove
the rubber plug from the micro USB
port and plug in a standard 5V power
supply with a micro USB connector to
the power port.
Step 2
Place the wall mount adapter on
a wall or an appliance near where
the possible water leak can occur.
Secure the wall mount adapter
with included double sided 3M
tape or via screws to the wall.
Once the wall mount is secured,
place LD-100 onto the hook with
the 4' cable connected.
Note: Do not place LD-100 on the floor, to protect the electronics
from water. Mount on a wall or on the side of the appliance.
Step 3 Please be sure the sensor module is powered off before plugging
in the 3D water sensing cable and star�ng the inclusion process.
When adding or removing op�onal extension cables, be sure to
have LD-100 powered off.
Inclusion/Exclusion: Add or remove the device into your network by a Z-Wave
cer�fied controller. If the controller is SmartStart compa�ble, refer to the controller
manufacturer app that allows the DSK code to be scanned, and scan the DSK code
on the side of the unit or on the box. If your controller is not S2/ SmartStart
compa�ble, the device can be added or removed using the tradi�onal method for
Z-Wave as follows:
1. Place your controller into Inclusion/Exclusion (Add/Remove) mode
by following the controller manufacturer's instruc�ons.
2. When the controller is ready, single click the bu�on of LD-100. The
controller should indicate that the new device was added/ removed
successfully. If the controller shows it failed, repeat the procedure.
Note: When on ba�ery power, the unit will stay awake for 5 minutes a�er
the bu�on is pressed. Once the unit detects inclusion has completed, it will
be able to start detec�ng every minute and will allow controllers to set any
necessary configura�on parameters.
www.ZLINKProducts.com
Manual Reset
If Inclusion s�ll fails a�er the 2nd a�empt, you need to first
reset the LD-100 before repea�ng the above step. Press the
bu�on and hold for 10 seconds to manually reset. The LED
will flash 5 �mes rapidly, if reset is successful.
Note: If LD-100 was previously Added (Included) in your network, rese�ng it
locally does not mean it has been removed from your controller so�ware. If you
wish to remove LD-100 from your network you will need to remove (Exclude) the
module from your network by your controller so�ware. The DSK code is required
to join or re-join a Z-Wave network using S2 level security. Therefore, please DO
NOT REMOVE the DSK code on the product and store a copy of the full DSK
printed on the package in a safe loca�on.
Use the manual reset procedure only in the event that the network primary
controller is lost or otherwise inoperable.
BASIC OPERATION
• The device will sense for water every 400 msec when plugged into a
standard 5V micro USB external power supply (not included).
• LD-100 will sense for water every 60 seconds on ba�ery power.
•
The device will beep 5 �mes once water is detected and will send a
no�fica�on report to controller; the device will stop beeping if the cable
is restored to dry or when the cable is unplugged.
• Once water is detected, frequency of the buzz and no�fica�on to the
controller can be set using configura�on parameter 2, the default se�ng
is every 10 minutes.
• When the cable dries, LD-100 will report a "no water detected" (0x00)
no�fica�on to the controller, however it will not buzz.
Temperature Measurement
LD-100 reports local temperature ( F) using the Mul�-level sensor command class
o
on Associa�on Group 1. On ba�ery, the unit will report temperature to the
controller once every 60 minutes. With external 5V micro USB power supply, the
unit will report temperature based on the se�ngs for configura�on parameter 3,
the default se�ng will report every minute.
Buzzer
When the device detects water on ba�ery or micro USB power, it will buzz 5
�mes. The buzzer may be disabled using configura�on parameter 4.
On micro USB power, LD-100 can be used as a no�fica�on buzzer when associated
with another device. For example, if it is associated to a door window sensor and it
gets triggered, LD-100 will beep one �me. The associated controller may trigger
the buzzer by sending a Switch Binary or Basic command class set command with
a non zero value to the sensor.
Note: We recommend to put fresh ba�eries a�er every water leak detected.
ADVANCED CONFIGURATION
Configurable Parameter Se�ngs: If your controller supports Z-Wave configurable
parameters, the following se�ngs can be modified.
Parameters
# Descrip�on
Beep and no�fica�on frequency
2
once water is detected
3 Temperature repor�ng interval on
micro USB power
4 No�fica�on buzzer
Associa�on
Group 1: Lifeline communica�on, you can associate up to five Z-Wave devices to
Group 1, it supports:
1. BATTERY_REPORT
2. NOTIFICATION_REPORT
3. SENSOR_MULTILEVEL_REPORT
4. DEVICE_RESET_LOCALLY_NOTIFICATION
Group 2: Basic Set, you can associate up to five Z-Wave devices to Group 2.
LD-100 will send a Basic Set to the associated devices, for example, turning
on lights or engaging the water auto shut-off valve, when water is detected.
www.ZLINKProducts.com
Values Default Bytes
0= every 10 minutes
1= every 5 minutes
0 1
2= every 30 minutes
30-255 seconds
60 1
0= Disabled
1 1
1= Enabled