1. Manuals
  2. Brands
  3. Tanda Manuals
  4. Lighting Equipment
  5. AQUATOP
  6. Installation manual

Tanda AQUATOP Installation Manual

Slatted cover
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation GUIDE 2019
Technics & Applications
Klaus Michael Kuehnelaan 9
2440 Geel (Belgium)
AQUATOP SLATTED COVER
Tel. : +32 14 23 74 95
Fax : +32 14 23 74 96
Website: www.t-and-a.be
Mail : info@aquatop.be

Advertisement

Table of Contents
loading

Summary of Contents for Tanda AQUATOP

  • Page 1 INSTALLATION GUIDE 2019 AQUATOP SLATTED COVER Technics & Applications Klaus Michael Kuehnelaan 9 Tel. : +32 14 23 74 95 Website: www.t-and-a.be 2440 Geel (Belgium) Fax : +32 14 23 74 96 Mail : info@aquatop.be...
  • Page 2 Index A0 – General Instructions A1 - Constructional preparations: Top Mount A2-1 - Constructional preparations: Underwater mount - In niche A2-2 - Constructional preparations: Underwater mount – In pool A3 - Constructional preparations: Underwater mount – In wall A4 - Constructional preparations: Underwater mount – On pool floor A5-1 - Constructional preparations: Underwater mount –...
  • Page 3 E7 – Connecting control: Top’Moov F – Use and maintenance G - Guarantee O1 - Finishing: Top mount – Bench O2 - Finishing: Underwater mount - In niche / in pool: Walking platform O3-1 - Finishing: Underwater mount - In pool: Panel (SCUBA-plates®) O3-2 - Finishing: Underwater mount - In wall: Panel O4 - Finishing: Underwater mount –...
  • Page 4 A pool cover is a tool to raise the safety , but can never replace the surveillance of a responsible adult! The expected life time of the cover heavily depends on way of installation, maintenance and service. MAN-AT-A1 Manual Aquatop (2019)
  • Page 5 Electrical prescriptions : • The electric motors of AquaTop covers are low voltage DC motors. Nevertheless, the current supply to the control box is 230V AC and requires to be secured respecting local laws and norms. • A differential switch guarantees the protection of people.
  • Page 6 Our standard plugs are made out of polyamide. These need to be fixed in full concrete or masonry. It is the responsibility of the installer to check the stability and if needed replace with chemical anchoring. MAN-AT-A1 Manual Aquatop (2019)
  • Page 7 Shape of the Cover roller shaft length support 10 m WOOD 15 m 10 m PVC + ALU 15 m Diameter roll + 50mm NO COVER: 15 m Finished support 25 m NO COVER: 15 m Unfinished support MAN-AT-A1 Manual Aquatop (2019)
  • Page 8 Cover length (m) (stairs incl.) ø Diameter ( ) Rollo cover ( mm) Slat dimension : 60 x 14 mm ø Diameter ( ) Rollo cover ( mm) Slat dimension : 67,5 x 16,5 mm Dimensions: MAN-AT-A1 Manual Aquatop (2019)
  • Page 9 ) Rollo cover ( mm) Slat dimension : 60 x 14 mm ø Diameter ( ) Rollo cover ( mm) Slat dimension : 67,5 x 16,5 mm SCUBA wall plates can be used? * On demand MAN-AT-A2-1 Manual Aquatop (2019)
  • Page 10 Dimensions: SS beam 100 x 100 x 5 mm (1.4306 - AISI 304) ALU beam 110 x 65 mm (anodized 25µm) MAN-AT-A2-1 Manual Aquatop (2019)
  • Page 11 ø Diameter ( ) Rollo cover ( mm) Slat dimension : 60 x 14 mm ø Diameter ( ) Rollo cover ( mm) Slat dimension : 67,5 x 16,5 mm Depth (d) versus pool wall (mm) MAN-AT-A2-1 Manual Aquatop (2019)
  • Page 12 Slat dimension : 60 x 14 mm ø Diameter ( ) Rollo cover ( mm) Slat dimension : 67,5 x 16,5 mm √ √ √ √ √ √ SCUBA wall plates can be used? * On demand MAN-AT-A2-2 Manual Aquatop (2019)
  • Page 13 Dimensions: SS beam 100 x 100 x 5 mm (1.4306 - AISI 304) ALU beam 110 x 65 mm (anodized 25µm) MAN-AT-A2-2 Manual Aquatop (2019)
  • Page 14 Adjustable bracket MAN-AT-A2-2 Manual Aquatop (2019)
  • Page 15 Slat dimension : 60 x 14 mm ø Diameter ( ) Rollo cover ( mm) Slat dimension : 67,5 x 16,5 mm B in mm ø + 100 Dimensions: C = X = B/ 2 A = C + (R/2) MAN-AT-A3 Manual Aquatop (2019)
  • Page 16 MAN-AT-A3 Manual Aquatop (2019)
  • Page 17 “O4 – Finishing: Underwater mount – On pool floor: Bench” • The Rollo cover can be covered with a single piece fibreglass bench (< 7m). • The bench will be made in 2 parts when poolwidth exceeds > 7m. MAN-AT-A4 Manual Aquatop (2019)
  • Page 18 Slat dimension : 60 x 14 mm ø Diameter ( ) Rollo cover ( mm) Slat dimension : 67,5 x 16,5 mm Dimensions: Width pool <7m Width > 7m Max diameter 610mm Width pool < 5m Max diameter 610mm MAN-AT-A4 Manual Aquatop (2019)
  • Page 19 Cover length (m) (stairs incl.) ø Diameter ( ) Rollo cover ( mm) Slat dimension : 60 x 14 mm ø Diameter ( ) Rollo cover ( mm) Slat dimension : 67,5 x 16,5 mm MAN-AT-A5-1 Manual Aquatop (2019)
  • Page 20 Dimensions: MAN-AT-A5-1 Manual Aquatop (2019)
  • Page 21 Cover length (m) (stairs incl.) ø Diameter ( ) Rollo cover ( mm) Slat dimension : 60 x 14 mm ø Diameter ( ) Rollo cover ( mm) Slat dimension : 67,5 x 16,5 mm MAN-AT-A5-2 Manual Aquatop (2019)
  • Page 22 Dimensions: If the „beach“ is used as an entry tot he pool, X ≤ 400mm ! MAN-AT-A5-2 Manual Aquatop (2019)
  • Page 23 PVC-tube into the concrete or full brickwork. Make 2 holes to this tube: 1x for resin, 1x for ventilation • Pour concrete (min. 25cm x 25cm) at the side opposite the motor to allow a good mounting of the flange. MAN-AT-A6 Manual Aquatop (2019)
  • Page 24 • Drill a hole of Ø35mm at the exact position of the roll-up shaft, through the wall. Non motor side: • Drill fixing holes for the flange through the wall, in line with the roller shaft and the motor flange. • Use the flange as a reference for this. MAN-AT-A6 Manual Aquatop (2019)
  • Page 25 • Fix the duct waterproof on the motor pit. • Equip the motor pit with a pipe connection, this can be used for ventilation and cables. • The lid of the motor pit can be covered with a tile. MAN-AT-A6 Manual Aquatop (2019)
  • Page 26 • The center of the wall duct is also the center of the roller shaft. Choose the Type of mounting who suits your project. Contact T&A in case of any doubts. We will help you to choose the correct wall duct in function of your type of pool. MAN-AT-A7 Manual Aquatop (2019)
  • Page 27 (see AT-MAN-B4 : Electrical preparations) Non motor side: • Drill fixing holes (Ø 9mm) for the flange through the wall, in line with the roller shaft. Use the flange as a mould to mark the holes. MAN-AT-A7 Manual Aquatop (2019)
  • Page 28 • The conduit fills-up with water and must always be kept above the water level of the pool to avoid emptying of the swimming pool, we strongly recommend to use our cable connection kit (see AT-MAN-B4 : Electrical preparations) Montage D MAN-AT-A7 Manual Aquatop (2019)
  • Page 29 • The conduit fills-up with water and must always be kept above the water level of the pool to avoid emptying of the swimming pool, we strongly recommend to use our cable connection kit (see AT-MAN-B4 : Electrical preparations). Pool wall already built: MAN-AT-A7 Manual Aquatop (2019)
  • Page 30 • The built-in flange is being mounted on top and being anchored on the wall with bolts and plugs. In order to guarantee a perfect connection in brickwork, we recommend a chemical anchor (this is not supplied from the manufacturer). MAN-AT-A7 Manual Aquatop (2019)
  • Page 31 • The flange is being mounted on top and being anchored on the wall with bolts and plugs. In order to guarantee a perfect connection in brickwork, we recommend a chemical anchor (this is not supplied from the manufacturer). MAN-AT-A7 Manual Aquatop (2019)
  • Page 32 • Two supports, mounted on the swimming pool border, will carry the roll-up shaft. • Max. dimensions ECOTOP®: 15 x 6 m. Indicating values: Cover length in m (stairs incl.) ø Diameter roll ( ) in mm MAN-AT-A7 Manual Aquatop (2019)
  • Page 33 Dimensions: With solar panel Without solar panel * electric supply cable (24 Vdc) Shape of the Support shaft support ECOTOP SOLAR ECOTOP without SOLAR MAN-AT-A7 Manual Aquatop (2019)
  • Page 34 MAN-AT-A7 Manual Aquatop (2019)
  • Page 35 ▪ If the Top'Moov is installed in an environment with much and strong wind, ask for an additional brake on T & A Rmax = 50 mm MAN-AT-A9 Manual Aquatop (2019)
  • Page 36 • Max width Pool: 5550mm • Length tracks: Standard 3 meter Distance tracks • Pool width + 2x150mm (min) • In case of a raised coping stone: 2x 150mm starting at the flat part of the stone! MAN-AT-A9 Manual Aquatop (2019)
  • Page 37 To avoid interference, never install control cables in the proximity of electric cable ! • It is recommended to install a lightning protection • T&A offers extension cable on rolls of 100m (article no. = AT-002564) MAN-AT-B1 Manual Aquatop (2019)
  • Page 38 To avoid interference, never install control cables in the proximity of electric cable ! • It is recommended to install a lightning protection • T&A offers extension cable on rolls of 100m (article no. = AT-002564) MAN-AT-B2 Manual Aquatop (2019)
  • Page 39 • Electric cables should always be guided through a conduit /protective tube. • To avoid interference, never install control cables in the proximity of electric cable ! • It is recommended to install a lightning protection. MAN-AT-B3 Manual Aquatop (2019)
  • Page 40 T&A strongly advices the use of a cable extension kit to extend the motor cable. This makes service easy. Inside the housing of this kit, there is plenty of space to stock at least 2m of motor cable. MAN-AT-B4 Manual Aquatop (2019)
  • Page 41 In order to facilitate service on a Scuba motor, it is recommended to have at least 2m of cable rolled in the extra shaft. Attention : T&A also offers extension cable for easy connection of automatic covers, packed in rolls of 100 m (Article number : AT-002564) MAN-AT-B4 Manual Aquatop (2019)
  • Page 42 MAN-AT-B4 Manual Aquatop (2019)
  • Page 43 Blue cable pre-installed at motor. Length 10m Till 25 meter: Cable 2 x 4² + (6 x 1,5² shielded) → AT-002564 Cable B: Cable Longer than 25 meter: Kabel 2 x 6² + (6 x 1,5² shielded) Max. Length 35 meter MAN-AT-B4 Manual Aquatop (2019)
  • Page 44 You are required to provide power supply to the EcoTop cover. The maximum distance between the motor and the power supply is 35 m. Powersupply cable between fuse box and control box: max 3x 1.5mm² Control panel 230 V – 6 A MAN-AT-B5 Manual Aquatop (2019)
  • Page 45 • Push the supports towards each other so that the bearings touch the bearing blocks in the roller shaft. • Position the roller shaft and supports symmetrically regarding to the middle of the pool above the pool end. MAN-AT-C1 Manual Aquatop (2019)
  • Page 46 Wooden bench • The SS supports is the frame for the bench. • See chapter “O1 – Finishing: Top mount – Bench”. Aluminium + PVC bench • See chapter “O1 – Finishing: Top mount – Bench”. MAN-AT-C1 Manual Aquatop (2019)
  • Page 47 PVC-nut on the wall duct, also using plenty of silicone. • Therefore you can use the key for the PVC-nut of the wall duct, see chapter “O9 – Option: Preparation – Key for PVC-nut of the wall duct”. – (art. no. AT-001738) MAN-AT-C2-1 Manual Aquatop (2019)
  • Page 48 • Let the mixture harden at 20°C for about 2 hours. The hardening time depends on the (ambient) temperature. • Make sure to stock and use the resin at room temperature to avoid the mixture from hardening too quickly MAN-AT-C2-1 Manual Aquatop (2019)
  • Page 49 Vaseline for positioning. The water seal ring should be 100% in line. N° Description N° Description Bearing Bolt Water seal ring Liner Flat sealing Flange Bolt Wall duct tube Liner ring PVC nut MAN-AT-C2-1 Manual Aquatop (2019)
  • Page 50 The 2 bolts only take care of the connection between driving shaft and roller shaft. Do not tighten bolts too much ! The 1000 Nm motor comes with a 42 mm driving shaft (instead of 30 mm). MAN-AT-C2-1 Manual Aquatop (2019)
  • Page 51 • The motor bracket is adjusted to the type of motor pit. Polyethylene motor pit • The motor bracket is being fixed on an internal L-profile of the pit. Concrete motor pit • The motor bracket is being fixed on to the pool wall. MAN-AT-C2-1 Manual Aquatop (2019)
  • Page 52 Option: With a liner, there is a risk the liner get damaged in case the cover gets stuck. To protect the liner we propose to install a protection on the wallduct. The protection will be fixated with silicone. Article AT-002763: MAN-AT-C2-1 Manual Aquatop (2019)
  • Page 53 PVC-nut on the wall duct, also using enough silicone. • Therefore you can use the key for the PVC-nut of the wall duct, see chapter “O9 – Option: Preparation – Key for PVC-nut of the wall duct”. – art. no. AT-001738 MAN-AT-C2-2 Manual Aquatop (2019)
  • Page 54 • Mix the polyester resin and the hardener intensively (these are always delivered in the right mixing proportion) and pour in the gaps around the wall duct tube until completely full. • Let the mixture harden at 20°C for about 2 hours. The hardening time depends on the temperature. MAN-AT-C2-2 Manual Aquatop (2019)
  • Page 55 Vaseline for positioning. The water seal ring should be 100% in line. N° Description N° Description Bearing Tile / Fiberglass Flange – pool side Water seal ring Flat sealing Wall duct tube Flange – motor side Bolt Liner ring PVC nut Bolt MAN-AT-C2-2 Manual Aquatop (2019)
  • Page 56 The 2 bolts only take care of the connection between driving shaft and roller shaft. Do not tighten bolts too much ! The 1000 Nm motor comes with a 42 mm driving shaft (instead of 30 mm). MAN-AT-C2-2 Manual Aquatop (2019)
  • Page 57 • The motor bracket is adjusted to the type of motor pit. Polyethylene motor pit • The motor bracket is being fixed on an internal L-profile of the pit. Concrete motor pit • The motor bracket is being fixed on the pool wall. MAN-AT-C2-2 Manual Aquatop (2019)
  • Page 58 MAN-AT-C2-2 Manual Aquatop (2019)
  • Page 59 • Bolt the pool wall between the flange and the outer flange with blind holes. Put flat sealings between the flange and the wall at both sides of the pool wall. MAN-AT-C3 Manual Aquatop (2019)
  • Page 60 The 2 bolts only take care of the connection between driving shaft and roller shaft. Do not tighten bolts too much ! The 1000 Nm motor comes with a 42 mm driving shaft (instead of 30 mm). MAN-AT-C3 Manual Aquatop (2019)
  • Page 61 • Rub Vaseline on the motor shaft and in the hollow shaft of the motor. • Put in the key and push the motor over the motor shaft. Note: in case of a hydraulic motor, a different key is supplied. This is attached to the motor. • Anchor the motor. MAN-AT-C3 Manual Aquatop (2019)
  • Page 62 Remark: If the standard wall plates do not offer you a solution, you can always contact T&A for tailor-made plates. Choice of wall plates Folded Folded with option: Dividing wall MAN-AT-C4 Manual Aquatop (2019)
  • Page 63 • Apply enough silicon after drilling the holes in order to assure the water tightness. • When using a liner, this will create a slight level difference. This difference can be compensated using a filler plate Spacer plate : AT-001923 MAN-AT-C4 Manual Aquatop (2019)
  • Page 64 • Fasten the setting ring with the screws on the flange, but leave a space of 5mm between the roll-up shaft and the setting ring. In this way the shaft will not get jammed in case of expansion. MAN-AT-C4 Manual Aquatop (2019)
  • Page 65 MAN-AT-C4 Manual Aquatop (2019)
  • Page 66 Don’t forget the flat sealing! • See chapter “A7 – Constructional preparations: Cable duct for SCUBA-drive®” Drill a 50mm hole. After placing the passage, spray with PUR to prevent damage to the PVC tube. MAN-AT-C5-1 Manual Aquatop (2019)
  • Page 67 • In case the flange with connection for the tube is installed on the wall and not in the concrete, the setting ring must not be installed. Alternatively; a cable gland can be used at this position, as such there is no water in the conduit. Art. no. AT-002883 MAN-AT-C5-1 Manual Aquatop (2019)
  • Page 68 There are 2 ways to stop the water: Pit for cable connection Cable gland screwed into the flange AT-002883 AT-002738 (PREFERED) MAN-AT-C5-1 Manual Aquatop (2019)
  • Page 69 Option: With a liner, there is a risk the liner get damaged in case the cover gets stuck. To protect the liner we propose to install a protection on the wallduct. The protection will be fixated with silicone. Article AT-002763: MAN-AT-C5-1 Manual Aquatop (2019)
  • Page 70 In this way the shaft will not get jammed in case of expansion. Alternatively; a cable gland can be used at this position, as such there is no water in the conduit. Art. no. AT-002883 MAN-AT-C5-2 Manual Aquatop (2019)
  • Page 71 MAN-AT-C5-2 Manual Aquatop (2019)
  • Page 72 • Anchor the supports with the delivered plugs and bolts. • Please note the overhanging border. See chapter “A8 – Constructional preparations: ECOTOP®” Aluminium supports Stainless steel supports (photovoltaic operation) MAN-AT-C6 Manual Aquatop (2019)
  • Page 73 • Push the cap towards the roller shaft. In this way the cap ‘clips’ under the fixing brackets of the support (2). • Cover up everything with the cover plate, in this way the cap will be fixed (3). MAN-AT-C6 Manual Aquatop (2019)
  • Page 74 Try to avoid excess shadow on the solar panel. ▪ Install the tracks (center/center) at distance B1 according to your order. ▪ Fix the tracks with the delivered plugs and bolts. ▪ Place the track stopper (see picture below). B1 (according to order) MAN-AT-C7 Manual Aquatop (2019)
  • Page 75 • Orientation of the slats: the curved side is the upper side of the slat; the open side is pointed to the pool end. The slat has a male (lip) and female (open chamber) side. MAN-AT-D Manual Aquatop (2019)
  • Page 76 Remark: Pay attention to the order of the operations; do not apply this method on both sides of the cover at the same time. The slats will get stuck!! Slide method MAN-AT-D Manual Aquatop (2019)
  • Page 77 • Cut the remainder of the ribbon. Make equally long! • Push the first slat through all the loops of the ribbons. Then click the next slat on the first one, so that the ribbon gets stuck between the slats. MAN-AT-D Manual Aquatop (2019)
  • Page 78 Correct the length of the ribbons such way that the tube hangs 50mm above the bottom of the niche when the cover is fully rolled. The ballast tube always guides the cover in the right direction while unrolling and slightly pushes the slats towards the shaft while rolling-up. MAN-AT-D Manual Aquatop (2019)
  • Page 79 • Except the standard caps, there are 2 different sizes (Small & Large). By using these caps you can make small changes in the length of the slats • You can easily remove the caps with a small screwdriver. MAN-AT-D Manual Aquatop (2019)
  • Page 80 Always use the correct screws! Use of incorrect screws can cause damage. Top mount without stairs – Welded and glued end caps (Profile 60 x 14mm): • The spoilers are attached with screws into the holes of the end caps MAN-AT-D Manual Aquatop (2019)
  • Page 81 Slide the spoiler towards the first slat • Fix the spoiler with the screws • Attention: use the correct screws! • Place the spacer profile in the second slat • Repeat this on the other side MAN-AT-D Manual Aquatop (2019)
  • Page 82 Slide the triangle with spoiler into the open chamber of the second slat • Click the triangle in the welded part of the first slat • Place the end cap of the second slat • Repeat this on the other side MAN-AT-D Manual Aquatop (2019)
  • Page 83 Attention: left and right are different! • Slide the spoiler towards the first slat • Fix the spoiler with the screws • Attention: use the correct screws! • Install the triangle • Repeat this on the other side MAN-AT-D Manual Aquatop (2019)
  • Page 84 (Profile 60 x 14mm) • Cut 25mm from the mail part of the first slat • Install the spoiler as shown on the drawing • Screw the spoiler into the open chamber of the second slat MAN-AT-D Manual Aquatop (2019)
  • Page 85 AT-004040 Top mount without stairs – glued end caps (Profile 67,5 x 16,5mm): • The spoilers are attached with screws into the holes of the end caps MAN-AT-D Manual Aquatop (2019)
  • Page 86 Attention: left and right are different! • Slide the spoiler towards the first slat • Fix the spoiler with the screws • Place the spacer profile in the second slat • Repeat this on the other side MAN-AT-D Manual Aquatop (2019)
  • Page 87 Push the spoiler into the open chamber of the second slat • Attention: left and right are different! • Slide the spoiler towards the first slat • Fix the spoiler with the screws • Install the triangle • Repeat this on the other side MAN-AT-D Manual Aquatop (2019)
  • Page 88 (Profile 67,5 x 16,5mm) • Cut 25mm from the mail part of the first slat • Install the spoiler as shown on the pictures • Screw the spoiler into the open chamber of the second slat MAN-AT-D Manual Aquatop (2019)
  • Page 89 (side) winds, the only correct solution would be to (automatically) lower the pool water level. This also offers a positive influence on the evaporation over the overflow channel. MAN-AT-D Manual Aquatop (2019)
  • Page 90 (The bracket needs to be able to pivot under the end cap) • Install the bracket at the side of the tail in case of a top mounted cover (The bracket needs to be able to pivot under the end cap) MAN-AT-D Manual Aquatop (2019)
  • Page 91 It is important to consider this problem during the design-process of the pool. In case of particular pool shapes it issometimes impossible to fully roll the cover ! MAN-AT-D Manual Aquatop (2019)
  • Page 92 Drawn at the male part of the slats the cutout at the point of the endcap of the skimmerslat Cut carefully the cutouts and install the slats. Install thes in the cover so the openings are at front of the skimmers in closed situation of the cover. MAN-AT-D Manual Aquatop (2019)
  • Page 93 E1 – Connecting control: External motor – Electrical 120, 250 & 500Nm Black = Grey MAN-AT-E1 Manual Aquatop (2019)
  • Page 94 Power supply 230V Earthing Power supply 230V Ethernet connection for software update Additional connector remote control Glass fuse 2A Fuse 20A Scroll up / OPEN Enter (confirmation of the choice) Scroll down / CLOSE Menu / return MAN-AT-E1 Manual Aquatop (2019)
  • Page 95 MAN-AT-E1 Manual Aquatop (2019)
  • Page 96 E2 – Connection control: External motor – Hydraulic 500 &1000Nm MAN-AT-E2 Manual Aquatop (2019)
  • Page 97 Programmable input Power supply 230V Earthing Power supply 230V Ethernet connection Additional connector remote control Glass fuse 2A Fuse 20A Scroll up / OPEN Enter (confirmation of the choice) Scroll down / CLOSE Menu / return MAN-AT-E2 Manual Aquatop (2019)
  • Page 98 MAN-AT-E2 Manual Aquatop (2019)
  • Page 99 E3 – Connecting control: SCUBA-drive® 140, 250 & 500Nm Black = Grey MAN-AT-E3 Manual Aquatop (2019)
  • Page 100 Programmable input Power supply 230V Earthing Power supply 230V Ethernet connection Additional connector remote control Glass fuse 2A Fuse 20A Scroll up / OPEN Enter (confirmation of the choice) Scroll down / CLOSE Menu / return MAN-AT-E3 Manual Aquatop (2019)
  • Page 101 MAN-AT-E3 Manual Aquatop (2019)
  • Page 102 E4 – Adjusting control: External motor & SCUBA-drive® (Universal control box) 1. Tree diagram MAN-AT-E4 Manual Aquatop (2019)
  • Page 103 • T4: to go into the menu, or to go back to the previous step = RETURN T1 = key 1 T2 = key 2 T3 = key 3 T4 = key 4 display: Select MENU Press T4 (MENU). MAN-AT-E4 Manual Aquatop (2019)
  • Page 104 Scuba motor 500Nm SCUBA-C Scuba motor 180Nm SCUBA-D Scuba motor 400Nm SCUBA-E Scuba motor 140Nm SCUBA-F Scuba motor 140Nm (100% soft start) HYDR-A Hydraulic motor 500/1000Nm HYDR-B Not used CUSTOM Only use in consultation with T&A MAN-AT-E4 Manual Aquatop (2019)
  • Page 105 – Adjusting control: External motor & SCUBA- drive® (Universal control box) 3. Extension”. If two channels are connected and detected, 2K appears on the display. If not, only one chanel is connected or detected. MAN-AT-E4 Manual Aquatop (2019)
  • Page 106 The confirmation will appear on the display. Keep T3 pressed until the ‘closed’ POSITION is reached. Press T2 and then T3 (both buttons together), to confirm the ‘closed’ P OSITION. The confirmation will appear on the display. Press T4 to go back • MAN-AT-E4 Manual Aquatop (2019)
  • Page 107 1. Boomstructuur MAN-AT-E4 Manual Aquatop (2019)
  • Page 108 Both opening and closing are done in dead man's function. The button must remain pressed. ➔ Operation by the pulse contact only works in AUTO mode ➔ Operation with a remote control configured in 3-button functionworks only in AUTO mode MAN-AT-E4 Manual Aquatop (2019)
  • Page 109 • STEP 4: Test the remote control with the sender. If necessary you can replace the white wire with the supplied external antenna. • STEP 5: (Only necessary in case of a replacement or additional sender or receiver) Set the sender and the receiver (see Extra: (Programming sender/receiver)). MAN-AT-E4 Manual Aquatop (2019)
  • Page 110 MAN-AT-E4 Manual Aquatop (2019)
  • Page 111 • Repeat for buttons B, C and D Programming sender/receiver is only necessary in case of a replacement or extra sender/receiver. In case of senders and receivers delivered together, the connection is already established so no need for programming. MAN-AT-E4 Manual Aquatop (2019)
  • Page 112 (Standard) Only one button to Open/Stop/Close the cover. 3-buttons (T3): Every order (Open – Stop – Close) has its own button. Button A: Open Button B: Close Button C: Stop Button D: No function for cover MAN-AT-E4 Manual Aquatop (2019)
  • Page 113 Minuten: (Standard = 10 min.) Displays the maximum time (min.). ‘-‘ (T3): Decreases the max time with one minute. The setting “0” minutes bridges this protection. There is a unlimited duration of use of the motor. MAN-AT-E4 Manual Aquatop (2019)
  • Page 114 In case the N.O./N.C.-contact gives a time deceleration (sec.) (To be set as: “Max time” – see above). Remark: In case of an external motor this input will be connected to the overheating protection of the motor (Sk-Sk). MAN-AT-E4 Manual Aquatop (2019)
  • Page 115 Contact J5 must be ‘open’ to let the cover run. N.C.: Contact J5 must be ‘closed’ to let the cover run. Tijd : In case the N.O./N.C.-contact gives a time deceleration (sec.) (To be set as: “Max time” – see above). MAN-AT-E4 Manual Aquatop (2019)
  • Page 116 STEP 2: (Place a 2 board) o STEP 3: The programming of the relay happens in the MENU (see 3. Extension: I/O- settings – Relay) o Below some examples of connection schemes which are possible with the extra relay card(s). MAN-AT-E4 Manual Aquatop (2019)
  • Page 117 MAN-AT-E4 Manual Aquatop (2019)
  • Page 118 MAN-AT-E4 Manual Aquatop (2019)
  • Page 119 The relay switches only temporarily = pulse contact. F11 – Error: The relay switches as soon as an error occurs on the display. F12 – Opening : Relay switches when the cover opens F13 – Closing : Relay switches when the cover closes MAN-AT-E4 Manual Aquatop (2019)
  • Page 120 Remark: F5 till F10 only possible with 1-button operation - see I/O-settings: Remote control MAN-AT-E4 Manual Aquatop (2019)
  • Page 121 In case the cover is closed, the control box will ask you to do this first. Press T3 to close the cover. In case of Master Slave or dead man's function is programmed, retunr with T4 and press T3 to close. Return to “protection lock” as described above. MAN-AT-E4 Manual Aquatop (2019)
  • Page 122 Confirm this value with T2 It is over this distance that the control box checks the set Amperage to check whether the locks are open or not. MAN-AT-E4 Manual Aquatop (2019)
  • Page 123 (both buttons together) to confirm the ‘middle’ POSITION If you push shortly on open or close the cover will stop at the middle position. If you push for 3 sec. the cover will pass the middle position without stopping. MAN-AT-E4 Manual Aquatop (2019)
  • Page 124 1CH/normal: To use if only 1 chanel of the encoder is available The control box checks only 1 Chanel of the encoder 2CH/normal: To use if 2 chanels of the encoder are available. The conrol box will check both signals of the encoder MAN-AT-E4 Manual Aquatop (2019)
  • Page 125 If you have e.g. Setting 20% the first 20% of the closing will be slower. If you press T1 for 5 seconds, the current position of the cover will be accepted as value. MAN-AT-E4 Manual Aquatop (2019)
  • Page 126 Press T2 (i) to get more information about the error message (s). Press T4 to return. The last error will be displayed under last err You can consult the previous error messages by pressing T3. In this example Last error -1, the penultimate error message MAN-AT-E4 Manual Aquatop (2019)
  • Page 127 PWM-value Displayed values: o Counter encoder o Percentage wicht he cover is open o Amperage M- M+ * o Temperature PCB ** o PWM-Value * Current and Amperage alternate ** Temperature brake and PCB alternate MAN-AT-E4 Manual Aquatop (2019)
  • Page 128 Note: Dead man's operation. Press T4 to return. (Contact your dealer before using this function) Open (T1): Opens the cover Close (T2): Closes the cover. After using this function, it is recommended to re-program the positions. MAN-AT-E4 Manual Aquatop (2019)
  • Page 129 Function to view the motor current 'real-time' during opening / closing of the cover. The current value is shown on the left. Press T4 to return o (Contact your dealer before using this function) Open (T1): The cover opens Close (T3): The cover closes MAN-AT-E4 Manual Aquatop (2019)
  • Page 130 • Runtime • Waterlevel 1 • Waterlevel 2 • Relay Positions: The end positions are deleted. possibly also the middle position. All: All settings are deleted The error log will not be deleted with any option. MAN-AT-E4 Manual Aquatop (2019)
  • Page 131 ENCODER CHECK THE SITUATION OF THE LOCKS; THE SETTED VALUE OF OPEN THE LOCKS – RESET THE ERROR MENU/PROT.LOCK EXCEEDED AND TRY AGAIN LOCK LOCKS NOT OPEN (MANUAL OR IF PROBLEM RETURNS? CONTACT AUTOMATIC) YOUR DEALER MAN-AT-E4 Manual Aquatop (2019)
  • Page 132 • To get the junction box in and out of the support, remove the 2 switches from the key button • The control box must be installed outside volumes 0,1 and 2. 1. Connection diagram Net cable power supply: 230V AC • Connect the motor and the key switch according to the scheme. MAN-AT-E5 Manual Aquatop (2019)
  • Page 133 • As the motor will run automatically in one and manually in the other direction, the connections of the White and Blue cable of the motor will depend on the position of the motor towards the pool. MAN-AT-E5 Manual Aquatop (2019)
  • Page 134 PLEASE NOTE: Respect the polarity! RED = + BLACK = - o STEP 3: Connect the plugs of the key contact and the motor on the charge regulator. o STEP 4 Connet the Initialisation button MAN-AT-E5 Manual Aquatop (2019)
  • Page 135 • Press the initialization button for at least 4 seconds • Release the button • Move the cover with the keyswitch in one movement to the end position you want to adjust. • Release the key. • You have now reprogrammed your position. MAN-AT-E5 Manual Aquatop (2019)
  • Page 136 E6: External Electrical500Nm – Scuba 500Nm MAN-AT-E6 Manual Aquatop (2019)
  • Page 137 Power supply 230V Earthing Power supply 230V Ethernet connection for software update Additional connector remote control Glass fuse 2A Fuse 20A Scroll up / OPEN Enter (confirmation of the choice) Scroll down / CLOSE Menu / return MAN-AT-E6 Manual Aquatop (2019)
  • Page 138 MAN-AT-E6 Manual Aquatop (2019)
  • Page 139 Programmable input Power supply 230V Earthing Power supply 230V Ethernet connection Additional connector remote control Glass fuse 2A Fuse 20A Scroll up / OPEN Enter (confirmation of the choice) Scroll down / CLOSE Menu / return MAN-AT-E6 Manual Aquatop (2019)
  • Page 140 MAN-AT-E6 Manual Aquatop (2019)
  • Page 141 - If the roller shaft runs longer than necessary (‘slipping‘), the run time must be reduced (-). Close the cover for at least 25%. Turn the screw contact at the pool side instinctively in the ‘-’ direction. Repeat ‘step 2’ as long as the cover keeps ‘revolving’ while ‘opening’. MAN-AT-E7 Manual Aquatop (2019)
  • Page 142 ▪ The key switch is set up a constant contact (Standard), the cover keeps running until end position if the key is released ▪ Remark: the key switch can also be set up differently. Therefore demount the key switch and install the yellow chip according to the position. MAN-AT-E7 Manual Aquatop (2019)
  • Page 143 1. Connection diagram Net cable power supply: 230V AC MAN-AT-E7 Manual Aquatop (2019)
  • Page 144 Wiring scheme Top’Moov Controller MAN-AT-E7 Manual Aquatop (2019)
  • Page 145 / user disconnected BATTERY LED : lights-up : battery low but user still active flashes slowly : user disconnected while battery recharges BATTERY GREEN : lights-up : battery charged flashes quickly : battery fully charged / regulator active MAN-AT-E7 Manual Aquatop (2019)
  • Page 146 In case of irregularities, turn off the cover immediately with the key switch on the operation panel. • Never force the cover during ‘opening/closing’. • A pool cover is a tool to raise the safety , but can never replace the surveillance of a responsible adult! MAN-AT-F Manual Aquatop (2019)
  • Page 147 The roller shaft needs to be blocked before removing the motor to avoid the slats from unrolling. (Key for blocking the “O9 – Option: Preparation shaft is available from your AQUATOP® supplier. See chapter and maintenance: Key for external electrical motor”.)
  • Page 148 20°C. Temperatures below 0°C will shorten the life span of the batteries Errors In case of defect or malfunction of the cover, always contact your AQUATOP® installer. 3. Ambient temperatues Technical area The control box and powerpack must be placed in a frost-free room.
  • Page 149 * Pool cover: • Project n° T&A: P ..Installed at: . . / . . / ..• Type: AQUATOP® / AQUAGUARD® • Type of construction: Top mount / Underwater mount •...
  • Page 150 * Pool cover: • Project n° T&A: P ..Installed at: . . / . . / ..• Type: AQUATOP® / AQUAGUARD® • Type of construction: Top mount / Underwater mount •...
  • Page 151 Technics and Applications bvba, Klaus-Michael Kuehnelaan 9, 2440 Geel, Belgium, guarantees its delivered goods as follows: The general guarantee period is 3 years for the AQUATOP® slatted pool cover. Conditions (valid from 01/01/2013) The invoice serves as proof of guarantee. The guarantee covers the costs of...
  • Page 152 • Screw the side pieces of the bench on the back and front. • Keep the back and front together with the SS bar, if delivered with the bench. • Put the wooden lid on top of the bench. MAN-AT-O1 Manual Aquatop (2019)
  • Page 153 Dimensions: ø Type Max. in mm W in mm H in mm L in mm max. 6,5m* * L = Pool width + 0,5m Installation: • Place the bench over the complete shaft and topmount supports. MAN-AT-O1 Manual Aquatop (2019)
  • Page 154 • Material: Tropical hard wood; IPE • Maximum concentrated load = 150 Kg. Remark: -Wooden grids can show slight transformations caused by the influence of atmospheric humidity and temperature. -Discoloration of the wood is typical for this material! MAN-AT-O2 Manual Aquatop (2019)
  • Page 155 When the SS beam is being ordered together with the wooden grids, this beam will be finished with the same wood on the crosscut side. When the SS beam is being ordered together with the PVC grids, this beam will be finished with white aluminium painted plate on the crosscut side. MAN-AT-O2 Manual Aquatop (2019)
  • Page 156 • Length is adjustable between 800 and 1000mm. • Order details: o Number of supports. Remark: In order to reduce bending of the beam, we recommend this with spans above 5m. MAN-AT-O2 Manual Aquatop (2019)
  • Page 157 Swimming pool width: 5,0m < W < 7,0m = 3 centre supports 7,0m ≤ W < 8,5m = 4 centre supports 8,5m ≤ W = 5 centre supports Maximum width of pool : B = 10 m MAN-AT-O2 Manual Aquatop (2019)
  • Page 158 • The first and the last support should be installed at min. 10 and max. 25cm of the side wall of the pool. • In case of a L-shape pool: make sure that the support guides the slats and not the endcaps. • Order details: o Number of supports. (Dimensions in mm) 1200 MAN-AT-O2 Manual Aquatop (2019)
  • Page 159 • Length is adjustable between 860 and 1090mm. • Order details: o Number of supports. REMARK Both brackets can be finished and connected with a profile, like a L-profile or T&A aluminium finishing profile. L-profile MAN-AT-O2 Manual Aquatop (2019)
  • Page 160 • The first and the last support should be installed at min. 10 and max. 25cm of the side wall of the pool. • In case of a L-shape pool: make sure that the support guides the slats and not the endcaps. 930 / 1150 mm MAN-AT-O2 Manual Aquatop (2019)
  • Page 161 MAN-AT-O2 Manual Aquatop (2019)
  • Page 162 4. Coverwash General: • Automatic cleaning system for the topside of the AquaTop cover. • Pool water in a separate high pressure circuit is jetted on top of- and in between the slats everytime the cover opens and/or closes. Description: •...
  • Page 163 • The dividing panel is available in the following two materials: Polyester or PVC. From 1051 1151 1251 1351 Height wall (WH) in mm Till 1050 1150 1250 1350 1400 Height difference (H) in mm 400 1000 1100 1200 MAN-AT-O3-1 Manual Aquatop (2019)
  • Page 164 Wall height = 1400mm (max.). • Consolidated with: o SS frame with pool width > 4 m (On request also possible under 4 m). • Installation o ≤ 4 m wall mounting brackets o > 4 m SS frame MAN-AT-O3-1 Manual Aquatop (2019)
  • Page 165 • The panel should be mounted symmetrically to limit the gap between the panel and the side walls of the pool. Width of the gap/side ≤ 8mm. • Turn the locking pin 90° to anchor the panel behind the lower beam. MAN-AT-O3-1 Manual Aquatop (2019)
  • Page 166 • The panel should be mounted symmetrically to limit the gap between the panel and the side walls of the pool. Width of the gap/side ≤ 8mm. • Turn the locking pin 90° to anchor the panel behind the lower stainless steel part. MAN-AT-O3-1 Manual Aquatop (2019)
  • Page 167 • The panel should be mounted symmetrically to limit the gap between the panel and the side walls of the pool. Width of the gap/side ≤ 8mm. • Turn the locking pin 90° to anchor the panel behind the lower stainless steel part. MAN-AT-O3-1 Manual Aquatop (2019)
  • Page 168 The gaps should never be bigger than 8mm. • Pull the upper bracket in its ‘closed’ position, to anchor the wall behind the SS frame. MAN-AT-O3-1 Manual Aquatop (2019)
  • Page 169 The gaps should never be bigger than 8mm. • Pull the upper bracket in its ‘closed’ position, to anchor the wall behind the SS frame. MAN-AT-O3-1 Manual Aquatop (2019)
  • Page 170 • The first and the last support should be installed at min. 10 and max. 25cm of the side wall of the pool. • In case of a L-shape pool: make sure that the support guides the slats and not the endcaps. 930 / 1150 mm MAN-AT-O3-1 Manual Aquatop (2019)
  • Page 171 MAN-AT-O3-1 Manual Aquatop (2019)
  • Page 172 • The dividing panel is available in the following two materials: Vinylester or PVC. From 1051 1151 1251 1351 Wall height (WH) in mm Till 1050 1150 1250 1350 1400 Height difference (H) in mm 1000 1100 1200 MAN-AT-O3-2 Manual Aquatop (2019)
  • Page 173 Wall height = 1400mm (max.). • Consolidated with: o SS frame with pool width > 4 m (On request also possible under 4 m). • Installation o ≤ 4 m wall mounting brackets o > 4 m SS frame MAN-AT-O3-2 Manual Aquatop (2019)
  • Page 174 • The panel should be mounted symmetrically to limit the gap between the panel and the side walls of the pool. Width of the gap/side ≤ 8mm. • Turn the locking pin 90° to anchor the panel behind the lower stainless steel part. MAN-AT-O3-2 Manual Aquatop (2019)
  • Page 175 The gaps should never be bigger than 8mm. • Pull the upper bracket in its ‘closed’ position, to anchor the wall behind the SS frame. MAN-AT-O3-2 Manual Aquatop (2019)
  • Page 176 • The first and the last support should be installed at min. 10 and max. 25cm of the side wall of the pool. • In case of a L-shape pool: make sure that the support guides the slats and not the endcaps. 930 / 1150 mm MAN-AT-O3-2 Manual Aquatop (2019)
  • Page 177 MAN-AT-O3-2 Manual Aquatop (2019)
  • Page 178 ≤ 8mm. • The bench should not be used as an entry tot he pool. If you decide to use the bench as an entry to the pool, you need to comply with the European standard EN_16582-1 MAN-AT-O4 Manual Aquatop (2019)
  • Page 179 • This fiberglass underwater bench is being carried by an SS beam and a tube, which are being anchored in the pool wall. This happens always after finishing the inside of the pool. • Dimension d1= rounded skimmer max 10mm MAN-AT-O4 Manual Aquatop (2019)
  • Page 180 8mm. • In case no bench is installed: the separate guiding plate should be installed. In combination with panel on floor (AT-002072) In combination with wall duct MAN-AT-O4 Manual Aquatop (2019)
  • Page 181 Remark: In case the pool has rounded edges, the bench cannot be installed. In case the pool has a pre-fabricated/pre-welded liner, utmost care should be used, probably the bench cannot be installed in this pool !!! MAN-AT-O4 Manual Aquatop (2019)
  • Page 182 • PCV plates to be tiled or finished with liner • Max width pool: 10m • Dimension d1= rounded skimmer max 10mm • Install the separation wall as written in the instructions O3-2 • Install the beams as written in the instructions of O5-2 MAN-AT-O4 Manual Aquatop (2019)
  • Page 183 • Install the fixationpoints on the wall following drawing below. Use enough silicone to make the holes watertight. • Dimension d1= rounded skimmer max 10mm • Hold the bench in an angel of 45 degrees above the round tube • Turn the bench into the right position. MAN-AT-O4 Manual Aquatop (2019)
  • Page 184 MAN-AT-O4 Manual Aquatop (2019)
  • Page 185 MAN-AT-O4 Manual Aquatop (2019)
  • Page 186 Key values : Coverlength in m (incl. stairs) Roll diameter (ø) in mm Profile 60 x 14 mm Roll diameter (ø) in mm Profile 67,5 x 16,5 mm Dimensions : PVC plates 1000 x 1000 x 20 mm MAN-AT-O5-1 Manual Aquatop (2019)
  • Page 187 (Ø 139,7 mm) is supplied. This needs to be installed on motor side. This flange is equipped with a special guiding mechanism for the slats. MAN-AT-O5-1 Manual Aquatop (2019)
  • Page 188 6. Allow to dry for half a day (refer to the adhesive manufacturer's instructions) 7. Apply the grout (e.g., PCI Durapox ® NT plus) Allow to dry sufficiently 8. Mount the plates in place in the water. Avoid exposure to the sun if they are not in the water. MAN-AT-O5-1 Manual Aquatop (2019)
  • Page 189 PVC plate at the bottom of the plate. 8. Let it dry for 24 hours 9. Mount the plates in place in the water. Avoid exposure to the sun if they are not in the water. MAN-AT-O5-1 Manual Aquatop (2019)
  • Page 190 AT-002885 – Set positioning PVC plates Install the pieces according the pictures below. MAN-AT-O5-1 Manual Aquatop (2019)
  • Page 191 • Natural stone (we recommend granite with a wall thickness of 30 mm) lays on a supporting beam (100 x 100 x 5 mm) equipped with slat guiding. • These supporting beams are available in AISI 304 and AISI 316L, we do recommend to use AISI 316L ! MAN-AT-O5-2 Manual Aquatop (2019)
  • Page 192 If the „beach“ is used as an entry tot he pool, X ≤ 400mm ! MAN-AT-O5-2 Manual Aquatop (2019)
  • Page 193 • Maximum concentrated load = 150 Kg. • The support is fixed against the pool wall with bolts and plugs. • The wall and the lining should be calculated on this load. • Order details: o Width of the pool MAN-AT-O5-2 Manual Aquatop (2019)
  • Page 194 Pay attention when there are corner roundings in the pool, it might be possible the panel cannot be installed! Don’t leave solid PVC plates uncovered in the open sunlight! They will be irreperably damaged! Damage caused through exposure to sunlight will not be subject to warranty. MAN-AT-O5-2 Manual Aquatop (2019)
  • Page 195 The cover will be driven with an external motor. Both motors will be connected to their own control box. These control boxes will be installed in a master-slave combination to each other. All given dimensions are measured from the concrete without tiles. MAN-AT-O6 Manual Aquatop (2019)
  • Page 196 ➔ Shaft & motor movable panel (with reductor) ➔ Shaft & motor cover ➔ Control box movable panel & cover ➔ Master slave initializing ➔ Test without water ➔ Filling the pool ➔ Installing the slats ➔ Re-programming end-positions MAN-AT-O6 Manual Aquatop (2019)
  • Page 197 The position of the wall duct for the cover is depending of the dimensions and shape of the pool. Contact T&A for the exact position. Install the wall duct as written in the manual chapter C2-2 Wall duct movable panel: Install the wall duct as written in the manual chapter C2-2 MAN-AT-O6 Manual Aquatop (2019)
  • Page 198 First drill the upper holes. Fixate to the wall and level all hinges. Mark the lower holes, remove the hinges and drill the lower holes. Mount the hinges to the wall. Use enough silicone in the drill holes to seal them in order to avoid leaking of water. MAN-AT-O6 Manual Aquatop (2019)
  • Page 199 Please note that between the sidewall and the panel and in between 2 panels you should always respect a 5 mm distance. Drill 7 mm sovereign holes on the top side of the panel and attach the panel to the hinges. MAN-AT-O6 Manual Aquatop (2019)
  • Page 200 ≤ 3m ≤ 4m ≤ 5m # PVC 1500x3000x20mm # PVC 1000x2000x20mm # Hinges / PVC Plate MAN-AT-O6 Manual Aquatop (2019)
  • Page 201 Shaft & motor movable panel: Install the shaft with rollers, gearbox (reductor) and motor. (See also chapter C2-2) Use both fixation plates. MAN-AT-O6 Manual Aquatop (2019)
  • Page 202 In closed position the lifting arm should be horizontal without the wheels touching the panel. Test without water & filling the pool: Make sure that both shafts work fine before filling the pool with water. MAN-AT-O6 Manual Aquatop (2019)
  • Page 203 Depending on the pool shape, the slats of side A or side B will go completely into the pit. Contact T&A Attach the slats of side A and Side B to one another just below the waterlevel using the connection strap 2 covers. (AT-003084) Re-programm endpositions: See chapter E2 – Initializing - basics MAN-AT-O6 Manual Aquatop (2019)
  • Page 204 • Provide an additional electrical cable 2 x 2,5²mm (L<25m) or 2 x 4mm² (25<L<35m) • Never connect the current supply to the transformer to the same jumper switch to which you connect the control box of the AquaTop. • Provide a drain pipe (3/4”) to drain away the pumped out water.
  • Page 205 • Fix the lock tightly to the pool wall. • Mount the ribbons with the loop on the last slat (similar to the fixing ribbons of the roller shaft), positioned right across the fixing positions. MAN-AT-O8-1 Manual Aquatop (2019)
  • Page 206 Locking: • Push the spring-button and hook the cover, in order to open; push the spring-button again and unlock the cover. Remark: Never forget to unlock the cover before opening! The cover might get damaged inevitably! MAN-AT-O8-1 Manual Aquatop (2019)
  • Page 207 • Two extra fixing positions are obliged according to the safety standard. • Woven ribbon gives strength at the end of the stairs. Roman stairs with radius > 1,5m • One fixing position is sufficient at the end of the radius ! MAN-AT-O8-1 Manual Aquatop (2019)
  • Page 208 Scroll to I/O SETUP. When this is next to T2, you confirm your choice by pressing T2. display: Choose PROT. LOCK Scroll to PROT. LOCK. When this is next to T2, you confirm your choice by pressing T2. MAN-AT-O8-1 Manual Aquatop (2019)
  • Page 209 Go back to MENU (T4) and then press T3 to ‘close’. Navigate after ‘closing’ back to the 4 display Prot. Lock, as described in previous steps. Press T2 (Teach). display: Confirm CURRENT-SETPOINT Rease this value with 1A Press T2. Go back to MENU (T4) MAN-AT-O8-1 Manual Aquatop (2019)
  • Page 210 • The maximum intermediate distance for two fixing positions is 2m. • The middle of the fixing position positions on the water level. • The appropriate safety standard determines the number of locking devices in specific pool designs. • See examples on next page : MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 211 • Two extra fixing positions are obliged according to the safety standard. • Woven ribbon gives strength at the end of the stairs. Roman stairs with radius > 1,5m • One fixing position is sufficient at the end of the radius ! MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 212 • Place the housing in the wall during the preparations at the right positions in the pool end. • Make sure the flange of the housing is positioned equally to the wall at the pool side. The housing must be positioned levelled horizontally ! MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 213 • Make sure the conduit enters the technical room at the position of the control box. • Clamp the tube around the fitting using a stretching clip. • Connect all fittings together (with conduits) in series, of which the 1 is connected with the technical room (see drawing below). MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 214 • Always pull the pneumatic hose Ø4mm at least 500mm into the fitting and tighten grommet well. Repeat this action until you reach the last fitting. The second connection in the last fitting needs to be locked by using the supplied stainless steel bolt M6. MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 215 • Apply self-adhesive seal on fitting and make sure that holes correspond. • Apply the liner and punch holes. • Mount the flange on the fitting with after placing the seal. • Clear the opening of the fitting with a cutter. MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 216 • Mount the adaptors at the ends of both pneumatic hoses Ø4 mm. • Now insert both adaptors in the T-connection piece. In last Top’Lock unit, no new hose will leave the unit, therefore apply end cap in the plug-in (see next picture). MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 217 • Be careful not to bend or damage pneumatic hoses during the installation process. item Description Art.nr. Liner Flange AT-2627 Top'Lock unit Bolt M6 x 20 (4x) AT-861 Mounting of the unit using the countersunk screws. MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 218 • Drill holes of Ø8mm and place the PVC plugs. • Mount the support at the wall. Mounting & cabling: Compressor set Mounting compressor set (Pneumatic) • Push the pneumatic hose Ø8mm arriving at the technical room in the open plug-in of the valve. MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 219 (see Options’) • Connect the cable, attached to the valve, to the relay card as shown in the diagram below. • Put the plug of the compressor into the 230Vac socket and switch on the compressor. MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 220 • The silicone profile is cut over a length of 4cm at both sides of the locking piece to make sure it can run into the funnel as far as possible MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 221 MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 222 Scroll to I/O SETUP. When this is next to T2, you confirm your choice by pressing T2. display: Choose PROT. LOCK Scroll to PROT. LOCK. When this is next to T2, you confirm your choice by pressing T2. MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 223 Go back to MENU (T4) and then press T3 to ‘close’. Navigate after ‘closing’ back to the 4 display Prot. Lock, as described in previous steps. Press T2 (Teach). display: Confirm CURRENT-SETPOINT Press T2. Go back to MENU (T4) display: Select MENU Press T4 (MENU). MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 224 When this is next to T2, you confirm your choice by pressing T2. display: Choose LOCK Scroll to LOCK F4. When this is next to T2, you confirm your choice by pressing T2. Go back to MENU (T4) The safety lock is ready to use! MAN-AT-O8-2 Manual Aquatop (2019)
  • Page 225 • It is advisable to store the external electric motor inside after the swimming period, in order to avoid damage during winter. • You place the tool in order to avoid the roller shaft to revolve or unroll. • Attention : only for diameter 30 mm. MAN-AT-O9 Manual Aquatop (2019)
  • Page 226 • If you want you can place some more anchorings in the block before it is being casted in. In case you are unsure about the anchoring. During the finishing of the pool you can place the self-adhesive sealing on the visible surface of the PE underwater mount block. MAN-AT-O9 Manual Aquatop (2019)
  • Page 227 • These must be built in already during the preparations. Description: • Material: SS 316L • Dimensions: o 100x100mm (BxH) o Thickness 25mm Insllation • Make sure there will be enough consolidation (concrete) around the block. MAN-AT-O9 Manual Aquatop (2019)
  • Page 228 • MAN-AT-O9 Manual Aquatop (2019)
  • Page 229 Z01 - Connecting control: : Vertical pit motor 300 – 450Nm MAN-AT-Z20 Manual Aquatop (2019)
  • Page 230 Scuba / external motor 500 Nm SCUBA-C Scuba motor 180 Nm SCUBA-D Scuba motor 400 Nm SCUBA-E Scuba motor 140 Nm HYDR-A Hydraulic motor 500/1000Nm HYDR-B NOT USED HYDR-C NOT USED CUSTOM ONLY USE IN CONSULTATION WITH T&A MAN-AT-Z20 Manual Aquatop (2019)
  • Page 231 • T4: to go into the menu, or to go back to the previous step = RETURN T1 = key 1 T2 = key 2 T3 = key 3 T4 = key 4 display: Select MENU Press T4 (MENU). MAN-AT-Z20 Manual Aquatop (2019)
  • Page 232 • Set the following values for a 300Nm motor (Increase or decrease with T1/T3 – confirm with T2) → 100 o Encoder Freq o Max Current → 16.5A → 200 o Start Open → 200 o Start Close → 0A o Soft Start MAN-AT-Z20 Manual Aquatop (2019)
  • Page 233 Cover READY to use The cover is now READY for normal use. To reprogram the end positions or to change “E4 – Adjusting control: other settings, see External motor & SCUBA-drive® (Universal control box) 3. Extension”. MAN-AT-Z20 Manual Aquatop (2019)
  • Page 234 Z20 – AT-002072 – Scuba plates On floor MAN-AT-Z20 Manual Aquatop (2019)
  • Page 235 Z21 – AT-002885 – Positioning set PVC plates MAN-AT-Z21 Manual Aquatop (2019)
  • Page 236 MAN-AT-Z22 Manual Aquatop (2019)
  • Page 237 Z22 – AT-001851 – Mouning kit fiberglass wall MAN-AT-Z22 Manual Aquatop (2019)
  • Page 238 MAN-AT-Z22 Manual Aquatop (2019)
  • Page 239 Z80 – AK-000362 – Wall duct Scuba thin wall MAN-AT-Z80 Manual Aquatop (2019)

Table of Contents