Mr. Soaker Hose 544 Instructions

Table of Contents

Quick Links

Download this manual

DISPLAY

Instructions for Mr. Soaker Hose #544 Timer:

Place cloth or use your hands to cover the solar panel before you install the 2‐AA Ni‐MH rechargeable batteries (High quality alkaline batteries may be used). New

rechargeable batteries usually need charging before use. Either fully charge your batteries or place in the timer for 3 days before programming. To re‐set timer,

remove batteries then re‐install.

◎Rain stop function

The rain sensor is the 2 contacts on top, next to the solar panel. Timer will stop immediately when raining, and it will not work until next running time after water

collecting area is dry.

Energy Saving Mode: This model has a built‐in electricity saving function. If there is not any operation, water timer will be in the sleeping mode. Press the third key

(wake up), then you can continue setting up the water timer. (Sleeping mode only stops the LCD from showing to save power, water timer is still running)

Battery Low Power: If Battery power is low LCD will display

batteries and reset time/programs.

*If you choose to select off mode

*The watering frequency has to be longer than 10 seconds, otherwise the setting is not complete.

*When inserting the batteries the valve will rotate automatically to make sure the valve is off.

*If there is no activity in programming after 60 seconds the timer will be in the sleeping mode.

Manual Open and Close: Press OPEN key, the water valve will open, LCD will display

Press close key, the water valve will close, LCD will display

will display

showing correct time and date.

A: Set current time and date:



Press wakeup

Press SET/OK key, LCD will display

Press SET/OK key again, LCD will display

Press AUTO/EXIT key twice to return to display mode

LCD will display

B: Set Watering Time (up to 8 programs)



Press wakeup

Press SET/OK key, LCD will display

Press + key, LCD will display

Press SET/OK key, Program 1‐8 will flash on the left, start with #1, Press SET/OK

Press SET/OK key, LCD will display

Next set amount of time you want the clock to run

Press SET/OK key, LCD will display

10. Press SET/OK key, LCD will display

01.

Current mode

02.

Setting mode

03.

S et the current time

04.

Cycles (used in C for propagation/mist settings)

. The electricity saving function will stop and the LCD will be continuously bright. Please change

, you can't set up frequency.

with the

blinking (setup mode)

, "hour" blinks, then press +/‐ to set hour. (Pay attention to AM or PM)

, "minutes" blinks, then press +/‐ to set minutes.

, "seconds" blinks, then press +/‐ to set seconds.

, "day" blinks, then press +/‐ to set day of the week.

showing correct time and date.

with the

blinking (setup mode)

blinks and is in the water setting mode

blink, press +/‐ to turn on or off (

, "hour" blinks, press +/‐ to set "hour" start time

, "minute" blinks, press +/‐ to set "minute" start time

, "hour" blinks, press +/‐ to set "hour" run time

, "minute" blinks, press +/‐ to set "minute" run time

, "seconds" blinks, press +/‐ to set "seconds" run time

05.

Watering setting

06.

Run time

07.

Exception watering

, all settings stop working. You must press AUTO/EXIT key to return to autorun mode. LCD

ICONS

08.

09.

10.

11.

Off

indicates on)

Battery

Operatiing

Table of Contents

Need help?

Do you have a question about the 544 and is the answer not in the manual?

Questions and answers

Summary of Contents for Mr. Soaker Hose 544

Page 1 05. Watering setting 09. Operatiing 02. Setting mode 06. Run time 10. On 03. S et the current time 07. Exception watering 11. Off 04. Cycles (used in C for propagation/mist settings) Instructions for Mr. Soaker Hose #544 Timer: Place cloth or use your hands to cover the solar panel before you install the 2‐AA Ni‐MH rechargeable batteries (High quality alkaline batteries may be used). New rechargeable batteries usually need charging before use. Either fully charge your batteries or place in the timer for 3 days before programming. To re‐set timer, remove batteries then re‐install. ◎Rain stop function The rain sensor is the 2 contacts on top, next to the solar panel. Timer will stop immediately when raining, and it will not work until next running time after water collecting area is dry. Energy Saving Mode: This model has a built‐in electricity saving function. If there is not any operation, water timer will be in the sleeping mode. Press the third key (wake up), then you can continue setting up the water timer. (Sleeping mode only stops the LCD from showing to save power, water timer is still running) Battery Low Power: If Battery power is low LCD will display . The electricity saving function will stop and the LCD will be continuously bright. Please change batteries and reset time/programs. *If you choose to select off mode , you can’t set up frequency. *The watering frequency has to be longer than 10 seconds, otherwise the setting is not complete. *When inserting the batteries the valve will rotate automatically to make sure the valve is off. *If there is no activity in programming after 60 seconds the timer will be in the sleeping mode. Manual Open and Close: Press OPEN key, the water valve will open, LCD will display ...
Page 2 11. Press SET/OK key to confirm, then press AUTO/EXIT key twice to take you back to automode. 12. LCD will display showing correct time and date. 13. Set Watering Days 14. Press SET/OK key, LCD will display with the blinking (setup mode) 15. Press +, 3 times, LCD will display , blinks and is in the exception water mode 16. Press SET/OK key, LCD will display , SU, MO, TU, WE, TH, FR, SA. Press +/‐ to indicate watering days you wish the timer to come on. Days NOT shown are off days. 17. Disregard (do nothing) , and here in the day settings as these are used for the propagation cycle setttings C: Set times to run in seconds (Propagation, Mist Systems). Example: If you want the timer to turn on every 3 minutes and run for 10 seconds. You would set the frequency for 3 minutes and the run time for 10 seconds.  Press wakeup Press SET/OK key, LCD will display with the blinking (setup mode) Press +, 2 times, LCD will display , blinks and is in the cycle water setting mode Press SET/OK key, LCD will display , ...