Table of Contents
Advertisement
Quick Links
CONCRETE GRINDER
Original instructions For your personal safety,
READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION:
For tools equipped with overload protection, when the motor shuts off due to overload,
always run the machine with no load for at least 3 minutes to reduce temperature before
returning to operation to avoid burn-out of the motor.
www.MACTOOL.co.za
Version:20161026
Advertisement
Table of Contents
Summary of Contents for Mactool AGP SM7
- Page 1 For tools equipped with overload protection, when the motor shuts off due to overload, always run the machine with no load for at least 3 minutes to reduce temperature before returning to operation to avoid burn-out of the motor. www.MACTOOL.co.za Version:20161026...
- Page 2 Power Input 110-120V:1700W, 220-240V:2200W Voltage See machine nameplate No Load/min 3200 - 6500 Wheel Diameter 180mm (7") Dimensions 246mm x 280mm x 325mm Weight 5.74(12.62Lbs) Edge Cut-Out in Skirt Magnet Clips Half-Moon Door Half-Moon Door Tail Cover Anti-vibration mountings Variable Speed Thumbwheel Trigger Switch Handles...
-
Page 3: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS When operating a power tool outdoors, use an extension cord suitable for outdoor use. WARNING! Read all safety warnings and Use of a cord suitable for outdoor use reduces all instructions. Failure to follow the the risk of electric shock. I f o p e rat i n g a p owe r to o l i n a d a m p warnings and instructions may result in location is unavoidable, use an ear th... - Page 4 ensure these are connected and properly used. working conditions and the work to be p er form ed. Us e o f t h e p owe r to o l fo r Use of dust collection can reduce dust-related hazards.
-
Page 5: Safety Warnings Common For Grinding Operations
SAFETY WARNINGS COMMON FOR undamaged accessory. After inspecting GRINDING OPERATIONS and installing an accessory, position yourself and bystanders away from the This power tool is intended to function as plane of the rotating accessory and run the a grinder. Read all safet y warnings, power tool at maximum no-load speed for i n s t r u c t i o n s , i l l u s t r a t i o n s a n d one minute. -
Page 6: Kickback And Related Warnings
spinning accessory could snag your clothing, precautions are taken. pulling the accessory into your body. Never place your hand near the rotating Regularly clean the power tool’s air vents. accessory. Accessory may kickback over your The motor’s fan will draw the dust inside the hand. -
Page 7: Electrical Connection
are of correct size and shape for your BEFORE USING THIS TOOL selec ted wheel. Proper wheel flanges WARNING: Some dust created by the power s u p p o r t t h e w h e e l t h u s re d u c i n g t h e sanding, sawing, grinding, drilling and other possibility of wheel breakage. - Page 8 BEFORE EACH USE INSPECT YOUR frequent use of the Power tool ) cause a MACHINE careless mistake. A careless fraction of a second is enough to cause a severe injury. • Disconnect the Power Scouring Machine from its power source to reduce the risk of If the machine makes an unfamiliar noise or injury from accidentally starting, before vibrates a lot, STOP IMMEDIATELY.
-
Page 9: Electrical Connections
involved . whether the tool is properly grounded check with a qualified electrician or service personnel. MOTOR AND ELECTRICAL WARNING: Do not permit fingers to touch the REQUIREMENTS terminals of plug when installing or removing the plug from the outlet to avoid injury or WARNING: To reduce the risk of electrical possible death from electrical shock. -
Page 10: Recommended Accessories
LIST OF PARTS voltage, (such as small size wire in the supply circuit) or to an overly long supply circuit NOTE: Before beginning assembly, check that all wire. Always check the connections, the load and the supply circuit whenever motor parts are included. -
Page 11: Vacuum Connection
Lock-Off Trigger Switch allowable current is exceeded. If the overload trips, remove from the work surface, release the switch On - The machine has a lock-off trigger switch. First and then switch back on. The machine will restart. press the switch button, then squeeze the trigger CAUTION: Whenever the machine overloads, switch to start the motor. -
Page 12: Safety Guard
TO O L C H A N G E – R e m ov i n g a n d To attach vacuum hose to Dust Port,hold machine Replacing Diamond Cup Wheel firmly with one hand. Then with a twisting motion push the vacuum hose onto the Dust Port. -
Page 13: Replacing Carbon Brushes
INSTALLING DIAMOND CUP WHEELS removal. W/ 7/8" (22.23MM) BORE. Replace the motor tail cover. Lock Nut Wrench L-Hex Wrench Arbor Nut Inner Flange STORAGE CAUTION: Do not store machine resting on its NOTE: To reinstall the same brushes, first make bristles –... - Page 14 KEEPING TOOL CLEAN accessible brushes, should be performed at an Authorized Service Center. Keep the machine and air inlet louver clean at all WARNING: If the replacement of the power times to ensure correct and safe working. Under supply cord is necessary, this has to be done extreme application conditions involving metal, dust can enter the interior of the machine.
- Page 15 WIRING...
-
Page 16: Exploded View
EXPLODED VIEW... -
Page 17: Parts List
PARTS LIST Parts Name Q'ty Parts Name Q'ty POWER SUPPLY CORD BEARING 6200-LLU CORD ARMOR ARMATURE SCREW M4 x 14 BEARING 6202-2NSE CORD CLIP SPACER SWITCH LOCK-OFF INPUT GEAR M1.5 x 11T SWITCH BUTTON GEAR PLATE GRIP-RIGHT UPPER SCREW M4 x 25 GRIP-RIGHT LOWER WIRE COVER SCREW M4 x 35... - Page 18 FLOOR GRINDING TROLLEY EXPLODED VIEW...
- Page 19 FLOOR GRINDING TROLLEY PARTS LIST Parts Name Q'ty HANDLE GRIP-LEFT REAR HANDLE GRIP-LEFT FRONT HANDLE GRIP-RIGHT REAR HANDLE GRIP-RIGHT FRONT SCREW M4 x 45 SCREW M4 x 30 SCREW M4 x 12 HANDLE COLUMN DEPTH ADJUST NUT FRAME WIRE LEAD 14AWG x 12cm MOTOR SWITCH POWER SUPPLY CABLE...