Operating Instructions; Checking For Leaks; Before Turning Lp Gas Supply "On; Before Lighting - Charmglow 82300 Owner's Manual

Operating Instructions

Inspect the visible portion of the hose before each use of the appliance. Inspect the entire hose
assembly at least annually.

Checking for Leaks

Burner Connections
Make sure the regulator valve and hose connections are securely fastened to the burner and
the tank.
If your unit was assembled for you, visually check the connection between the burner pipe and
orifice. Make sure the burner pipe fits over the orifice.
WARNING: Failure to inspect this connection or follow these
instructions could cause a fire or an explosion which can cause death,
serious bodily injury, or damage to property.
Please refer to diagram for proper installation.
If the burner pipe does not rest flush to the orifice, please contact 1.800.762.1142 for
assistance.
Tank/Gas Line Connection
Make 2-3 oz. of leak solution by mixing one part liquid dishwashing
soap with three parts water.
Make sure control knobs are off.
Attach (1) 14.1 oz or (1) 16.4 oz LP gas tank.
Spoon leak check solution at all "x" and arrow locations.
If any bubbles appear disconnect gas tank, reconnect and re-test. If
you continue to see bubbles after several attempts, disconnect LP gas
source and contact 1.800.762.1142 for assistance.
If no bubbles appear after one minute turn tank "OFF", wipe away
solution and proceed.
Before Turning Gas Supply ON
Your heater was designed and approved for OUTDOOR USE ONLY. DO NOT use it inside a
building, garage, or any other enclosed area.
Make sure surrounding areas are free of combustible materials, gasoline, and other flammable
vapors or liquids.
Ensure that there is no obstruction to air ventilation.
Be sure all gas connections are tight and there are no leaks.
Be sure the access panel is clear of debris.
Be sure any component removed during assembly or servicing is replaced and fastened prior
to starting.

Before Lighting

Heater should be thoroughly inspected before each use, and by a qualified service person at
least annually.
If relighting a hot heater, always wait at least 5 minutes for gas to dissipate.

Lighting

1. Turn control knob to "OFF" position.
2. Turn on gas at LP gas tank.
3. Push in control knob and rotate to "ON" position. This will
activate the built-in ignitor and light the burner. If necessary,
keep depressing and rotating knob until burner lights.
4. Once burner is lit, hold control knob in for at least 30 seconds
and release.
5. If burner does not stay lit, turn to "OFF" position and wait 5
minutes and repeat steps 2
and 3.
6. If ignitor does not light burner, use a lit match positioned against
the bottom of emitter screen at burner location, and repeat steps
2 and 3.
7. Once burner is lit, rotate knob to desired heating level.
If you experience any ignition problem, turn off the heater and gas
supply, and consult "Troubleshooting".
Caution: Avoid inhaling fumes emitted from the
heater's first use. Smoke and odor from the burning
of oils used in manufacturing will appear. Both smoke and odor will dissipate
after approximately 30 minutes. The heater should NOT produce thick black
smoke.
Note: The burner may be noisy when initially turned on. To eliminate excessive noise from the
Outdoor Patio Heater Model No. 82300
burner, turn the control knob to the "LOW" position. Then, turn the knob to the level of heat
desired.

When heater is "ON":

Emitter screen will become bright red due to intense
heat. The color is more visible at night.
Burner will display tongues of blue flame. These flames
should not be yellow or produce thick black smoke,
indicating an obstruction of airflow through the burners.
If yellow flame is detected, turn off heater and gas
supply and consult "Troubleshooting".
Visually check burner flames at each use and make
sure flame height matches illustration.

Re-lighting

Note: For your safety, control knob cannot be turned on
without first depressing control knob in off position and
then rotating to on.
1. Turn gas control knob to off.
2. Wait at least 5 minutes to let gas dissipate before
attempting to relight burner.
3. Repeat the "Lighting" steps 2 and 3.

Turning Off

1. Rotate gas control knob to off position. Normally, burner will make a slight popping sound
when extinguished.
2. Turn off gas at LP gas tank, or unscrew 14.1 oz or 16.4 oz LP gas tank.
Regualtor Connection
3. Remove access panel.
4. Unscrew gas line from regulator.
5. Close access panel.
Note: After use, some discoloration of the emitter screen is normal.

Cleaning and Care

Notices
1. Abrasive cleaners will damage this product.
2. Never use oven cleaner to clean any part of heater.
3. Do not clean any heater part in a self cleaning oven. The extreme heat will damage
the finish.
4. More frequent cleaning may be required as necessary. It is imperative that control
compartment, burners and circulating air passageways of the heater be kept clean.
5. Spiders and insects can create a dangerous condition that may damage heater or
make it unsafe. Keep burner area clean of all spiders, webs, or insects. Clean burner
holes by using a heavy-duty pipe cleaner. Compressed air may help clear away
smaller particles.
6. Inspect heater before each use.
7. Have heater inspected annually and repairs should be made by a qualified service
person.
8. Check heater immediately if any of the following conditions exist:
OFF
a. The smell of gas in conjunction with extreme yellow tipping of burner flames.
b. Heater does not reach proper temperature.
ON
HIGH
Note: At temperatures less than 40ºF, heat output will be reduced.
LOW
c. Heater's glow is excessively uneven
d. Burner makes popping noises during use.
Note: A slight pop is normal when burner is extinguished.
9. Carbon deposits may create a fire hazard. Keep dome and emitter clean at all times.
OFF
10. Do not clean heater with combustible or corrosive cleaners. Use warm, soapy water.
ON
11. Do not paint engine, engine access panel or dome.
HIGH
12. This heater should be thoroughly cleaned on a regular basis.
LOW
13. After a period of storage and/or non use, check for leaks, burner obstructions and
inspect for any abrasion, wear, cuts to the hose.