• Install at least 5 feet (1 .5 m) from all metal surfaces . A spa may be installed within 5 feet CONQUEST SPAS SAFETY INSTRUCTIONS of a metal surface if each metal surface is permanently connected by a minimum No . 8 AWG (8 .4 mm ) solid copper conductor attached to the wire ground connector on the Read And Follow All Instructions...
AVO I D I NG R IS K OF H YP E RT HERM IA Important: The following contains important spa information, and we strongly encourage you to read The causes, symptoms and effects of hyperthermia may be described as follows: and apply them .
INS TA L LATION I NST RU CT IONS S PA S P E CI FI CAT ION S Location Preparation Your Conquest Spas model is totally self-contained and portable . You can install the spa outside or inside . Preferable places are on a patio, deck or indoors . The spa should always be placed on a Average level, load bearing, solid surface in accordance with your local building code requirements .
EL ECT R I CAL RE QU IREMEN TS AND P RECAUTIONS Electrical Spa Wiring Connection Instructions Your Conquest Spas model has gone through numerous tests to verify that all of the spa Due to the risk of damaging the PC Board, the equipment and the RCD tripping, never, functions operate .
Page 7
WI R I N G S C HE M AT IC ELE CTRI CAL SE RV IC E CONFI GURATI ON OP TIONS Single Service (1 x 16 Amp or 1 x 32 Amp) This option is configured and shipped as the default. •...
Start-up Procedures (Contender and Challenger SE Only) IN ITIAL OPERATIN G INS TRUCTIONS For a successful start-up, remove both filter cartridges, and fill the spa with water through the Start-Up and Refill Procedures openings in the filter compartment . Your Conquest Spas model has been tested at the manufacturing plant to ensure that all of the Locate the filter compartment area .
Page 9
Start-up Procedures Start-up Procedures (Victory and Challenger LE Only) (Conqueror LE, Majesty LE, Realm, Laurel, Elation, Baroque) Your Conquest Spas model has been tested at the manufacturing plant to ensure that all of the 1. For a successful start-up, fill the spa with clean water, free of debris, through the Whisper spa functions operate.
5. After the pumps are primed turn off by pressing the Jet(s) button(s). Next manually exit EQ UIP M ENT M A INT E NA NC E the priming mode by pressing either the Warm or Cool button. After you have manually exited the priming mode the display will show the set temperature, which defaults at 100°...
CONT E N D ER & C H AL LE NG E R S E RI E S V I C TO RY & CHA L LE N G E R S E R IE S O P E R AT I N G TH E HYDRO P UM P (S )/JE T BUTTON (S ) OP E RAT I N G T H E H YD R O PU M P( S) /J E T BUTTON ( S ) (Grandeur •...
D I AG NOSTI C MESSAG ES SPA CA R E A ND WAT E R M A INT E NA NC E Scroll Message Meaning Action Required GE N E R AL I N FO RM AT ION NO COMM Call for Service The panel is not receiving communication from the system Conquest Spas are manufactured from the highest quality, most durable materials available today .
Filter System 3 . To reinstall the spa pillow, carefully bend the pillow slightly to allow the slit on the back Conquest Spas are equipped with two standard filter cartridges . As with any filtering system, the of the pillow to slip over the attachment bar retainer on the spa shell . 4 .
Important reminders: 9 . Place the vacuum hose down the filter cartridge openings and vacuum any water from • Do unlock and release all cover locks before attempting to open cover . filter compartment . • Do remove snow buildup to avoid damage of the foam core from the additional weight of the 10 .
Example: At low total alkalinity levels, the water’s pH easily drifts, making frequent pH WATER Q UALITY M AINTE NANC E adjustments necessary and the added expense of multiple chemical treatments . General Information On the other hand, a high total alkalinity level keeps the water pH rigidly fixed . If pH As the owner of a Conquest Spa, endless hours of entertainment, recreation, and relaxation await adjustment is necessary, you will need unusually large amounts of treatment chemicals you .
Page 16
Shock Treatment with Granular Disinfectant OP E RATI ON S TR OUB L E S H OOTI NG G UI D E Adding granular chlorine or bromine disinfectant to the water in amounts much larger than normal is called “shocking” the spa and should not be confused with non-chlorine shock . An occasional shock treatment destroys algae, bacteria, and chloramines .
SERV ICE A ND WA R R ANT Y INF O R M AT ION OPERATIONS TROUBLE SHOOTING GUIDE General Service Information Conquest Spas™ models have been designed to provide years of trouble-free use. As with any appliance, problems may occasionally occur that require the expertise of a qualified service P R OB LE M P R O BA BL E C AU S E SO LUT I ONS...
Need help?
Do you have a question about the Conquest Spas Gandeur and is the answer not in the manual?
Questions and answers