Summary of Contents for Dolby Laboratories CID1020
- Page 1 Dolby Integrated Media Server Docking Station Manual 23 June 2020 IMS.OM.005903.DRM Issue 3...
- Page 2 Dolby Laboratories, Inc. 1275 Market Street San Francisco, CA 94103-1410 USA Telephone 415-558-0200 Fax 415-645-4000 http://www.dolby.com Trademarks Dolby and the double-D symbol are registered trademarks of Dolby Laboratories. The following are trademarks of Dolby Laboratories: ™ ® Dialogue Intelligence Dolby Theatre ®...
- Page 3 Important safety instructions THE LIMITED WARRANTY AND WARRANTY EXCLUSIONS MAY BE FOUND AT THE FOLLOWING URL: https:// www.dolby.com/us/en/about/warranty-and-maintenance-policies.html Important safety instructions 1. This product is intended for indoor use only. 2. Do not install near any heat sources, such as radiators, heat registers, or other apparatus that produce heat.
-
Page 4: Table Of Contents
Contents Contents 1 Introduction to this documentation....................5 1.1 About the Dolby Integrated Media Server Docking Station................. 6 1.2 Contacting Dolby ............................7 2 Hardware components........................8 2.1 Packing list..............................9 2.2 Power supply requirements...........................9 3 Installing the Dolby IMS Docking Station..................10 3.1 Placing the Docking Station in the horizontal position................11 3.2 Standing the Dolby IMS Docking Station.................... -
Page 5: Introduction To This Documentation
Introduction to this documentation This documentation provides instructions for setting up and operating the Dolby Integrated Media Server (Dolby IMS) Docking Station. • About the Dolby Integrated Media Server Docking Station • Contacting Dolby Dolby Integrated Media Server Docking Station Manual IMS.OM.005903.DRM Issue 3 23 June 2020... -
Page 6: About The Dolby Integrated Media Server Docking Station
Introduction to this documentation 1.1 About the Dolby Integrated Media Server Docking Station The Dolby Integrated Media Server (Dolby IMS) Docking Station is a hardware solution for quickly and efficiently charging the battery in certain Dolby media blocks. The battery maintains the secure clock and security identity of the media block. -
Page 7: Contacting Dolby
Contacting Dolby Attention: This product is intended to power and charge your Dolby IMS unit. It cannot restore the private key of your Dolby IMS (that was lost due to a low battery). A Dolby IMS without a private key forces the unit into Federal Information Processing Standards (FIPS) lock. -
Page 8: Hardware Components
Hardware components Hardware components The Dolby IMS Docking Station requires specific hardware components and the correct power supply for proper and safe operation. • Packing list • Power supply requirements Dolby Integrated Media Server Docking Station Manual IMS.OM.005903.DRM Issue 3 23 June 2020... -
Page 9: Packing List
Packing list 2.1 Packing list The packing list provides the hardware components that ship with the product. • Dolby Integrated Media Server Docking Station (Dolby part number CAT1743) • Two metal feet (to set up the Docking Station vertically) • Four small screws (to set up the Docking Station vertically) 2.2 Power supply requirements The Dolby IMS Docking Station requires an external AC adapter power supply. -
Page 10: Installing The Dolby Ims Docking Station
Installing the Dolby IMS Docking Station Installing the Dolby IMS Docking Station You have the option to stand the Docking Station in a vertical position or a horizontal position, depending on your operating environment. • Placing the Docking Station in the horizontal position •... -
Page 11: Placing The Docking Station In The Horizontal Position
Placing the Docking Station in the horizontal position 3.1 Placing the Docking Station in the horizontal position You have the option to place the Dolby IMS Docking Station in a horizontal position. About this task You need a stable and non-conductive surface to place the Docking Station on. Procedure Place the Docking Station down on the surface with the LED indicator cutout facing up. -
Page 12: Plugging In The Power Adapter
Installing the Dolby IMS Docking Station Figure 4: Vertical position 3.3 Plugging in the power adapter You must connect one end of the power adapter to an AC power supply outlet, and the other end to the Dolby IMS Docking Station. Prerequisites The power switch must be in the off position. -
Page 13: Charging The Dolby Ims Battery
Charging the Dolby IMS battery About this task Attention: The back panel displays two LEDs: Wrong Polarity and Over Voltage. If your power adapter is of the correct voltage and polarity, then neither of these LEDs will illuminate. Figure 5: Back panel with LEDs labeled If you connect a power supply and the wiring has reversed polarity (tip negative), the Wrong Polarity LED will illuminate. - Page 14 Installing the Dolby IMS Docking Station About this task The Dolby IMS has a charging LED to indicate when it is charging and when it is fully charged. The Docking Station has a rectangular cutout that enables you to view the charging LED on the Dolby IMS. While the Dolby IMS is charging, its green LED battery indicator steadily illuminates.
-
Page 15: Troubleshooting
Troubleshooting You can troubleshoot the Dolby IMS Docking Station and replace one or both fans, and replace the fuse if it is damaged. • Replacing the fan • Replacing the circuit board fuse Dolby Integrated Media Server Docking Station Manual IMS.OM.005903.DRM Issue 3 23 June 2020... -
Page 16: Replacing The Fan
Troubleshooting 4.1 Replacing the fan Replace one or both fans if they are damaged or not working. Prerequisites Turn off the Docking Station, unplug the power supply, and then remove the Dolby IMS. Inspect one or both fans for any obstruction or obvious issue. About this task The fan part number is Sunon Maglev MF60251V1-10000-G99. -
Page 17: Replacing The Circuit Board Fuse
Replacing the circuit board fuse 6. Take the new fan (with fan guard reinserted), and align it where the four screw holes are located. 7. With a Phillips screwdriver, screw in the four screws from the inside of the Docking Station. 8. - Page 18 Troubleshooting 2. Using a fuse puller, carefully reinsert the new fuse on the circuit board. What to do next To test the new fuse functionality, plug the power supply into the Docking Station and then switch the power on. Check whether the fuse is working properly. Dolby Integrated Media Server Docking Station Manual IMS.OM.005903.DRM Issue 3 23 June 2020...
-
Page 19: Documentation Revision History
Documentation revision history The documentation revision history lists the date, issue number, and description of all publications of Dolby Integrated Media Server Docking Station Manual . Date Issue Description 06 March 2020 Initial release 11 March 2020 Updates made to chapters 3 and 4 23 June 2020 Small text inserted for clarification Dolby Integrated Media Server Docking Station Manual IMS.OM.005903.DRM Issue 3...
Need help?
Do you have a question about the CID1020 and is the answer not in the manual?
Questions and answers