Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for ORBOT MICRO HOSOM
- Page 1 TWIN-HEAD ORBITAL STAIR & UPHOLSTERY TOOL OPERATING MANUAL ( US ) 2020...
- Page 2 • Costs and risks of transport relating directly or indirectly to the guarantee of this product. • Consumable items such as brushes, drivers, velcro discs, gliders, pads and so forth. ORBOT has a policy of continual product development and we reserve the right to alter specifications without prior notice.
-
Page 3: Table Of Contents
8 - 9 Machine Operating Instructions 9 - 10 User Maintenance & Troubleshooting 10 - 11 Additional Maintenance & Service Information Disposal & Recycling Information Appearance of Your ORBOT MICRO Technical Specifications ORBOT MICRO Parts Diagrams & Parts Listing 14 - 15... -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS This instruction manual is furnished with each . The entire manual should be ORBOT MICRO read carefully before using the and retained for future reference. ORBOT MICRO GENERAL SAFETY RULES WARNING ® Read all instructions. Failure to follow all instructions listed below may result in electric This instruction manual is furnished with each Cyclo Model 5, 5-Pro, 5C &... - Page 5 SAFETY INSTRUCTIONS k) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. l) Avoid accidental starting. Ensure the switch is in the off-position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.
- Page 6 SAFETY INSTRUCTIONS WARNING Safety Warnings bb) The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart. cc) The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool.
- Page 7 Size of Wire in Cord: 18 AWG (0.75mm2), 16 AWG (1.0 mm2) Motor rr) Your ORBOT MICRO is powered by a sturdy motor. Be certain your power supply agrees with that shown on the name plate (a.c. means alternating current). Variance in your power supply’s voltage may result in loss of power and overheating.
-
Page 8: Orbot Micro Set-Up
Quick Connect Adapters, Scrub Brushes, ProGuard Orbital Backing Plates and other Attaching Velcro Driver Plates and Scrub Brushes a) Lay the ORBOT MICRO upside-down on your lap, bench or flat surface. lisher upside-down on your lap, a bench or flat surface. You may also use the cardboard insert removed from b) Fit the flat wrench around the hex nut-like adapter part of the counterweight. -
Page 9: Machine Operating Instructions
MACHINE OPERATING INSTRUCTIONS ORBOT MICRO has two heads rather than the single head common on other orbital-motion tools. As soon as the ORBOT MICRO is placed on a working surface and powered on, orbital “hand-rubbing”... -
Page 10: User Maintenance & Troubleshooting
Refer to General Cleaning Instructions. USER MAINTENANCE & TROUBLESHOOTING Instructions below on care and maintenance of your ORBOT MICRO. You can also visit our website at www.orbotusa.com for tutorials and video instructions on proper tool care and maintenance. How To Maintain Your ORBOT MICRO Ensure machine is disconnected from electrical supply before inspection or maintenance is performed. - Page 11 The motor is only for the voltage specified on the nameplate. Voltage should not vary more than 10% over or under the voltage shown on the nameplate. Although the ORBOT MICRO is built to last a lifetime, it can encounter problems from heavy wear and tear. All problems are repairable, and can most often be repaired by a mechanically inclined technician or user.
-
Page 12: Additional Maintenance & Service Information
400 hours of use. If necessary, re-lubricate with Texaco Multifax #2 or equivalent. Timing: The secret of the operation of your ORBOT MICRO lies in the fact that the two heads are timed exactly 1/2 turn apart. This is necessary for the balanced operation of the tool. If the machine is disassembled, use the following procedures to insure proper timing of the heads. -
Page 13: Technical Specifications
TECHNICAL SPECIFICATIONS HOSOM & HOSOM-230V Power Supply Nominal Current Output HOSOM: 115 V a.c., 60 Hz, 2.0A .35 h.p. (.23kW) HOSOM-230V: 30 V a.c., 50 Hz 1.0A .35 h.p. (.23kW) HOSOM: 2800 to 3200 RPM HOSOM-230V: n0 = 3200/min Weight: 6.5 lbs (2.9 kg) Pad or Bonnet Capacity: 2 x 4”... - Page 14 ORBOT MICRO PARTS DIAGRAMS Please Note: Above 2 diagrams only are different due to the motor.
- Page 15 Screw, Field Retaining Armature, 115V, 60Hz Screw, Motor Bearing Hold Bearing, Lower Motor Lock Ring for Pinion Gear Orbot Micro Switch, Double Pole, Single Throw 230V Crimp-on Wire Connector Screw, Grounding Power Cord Assembly (U.S.A. Standard) Orbot Micro Switch, 115V...
- Page 16 “Innovators in Orbital Floor Care” 3275 Corporate View, Vista, CA 92081, USA P: 760-936-8054 | CustomerService@orbotusa.com www.orbotusa.com EXPERIENCE THE NEW METHOD to CLEAN FLOOR!