Multilink 010-505-10 Installation And Operation Manual

Safety automatic transfer switch

Advertisement

Quick Links

Documented Power Supply Models
MODEL
Safety Automatic
Transfer Switch
Safety Automatic
Transfer Switch
Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com
Safety Automatic Transfer Switch
Installation and Operation Manual
PART NUMBER
010-505-10
010-505-20
© Multilink Inc. 2020 • All Rights Reserved
INPUTS
OPTIONS
120 VAC 60Hz
Mates w
Series
120 VAC 60Hz
Unive
Line Interactive
U
ith EDP
Only
rsal with
PS'

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 010-505-10 and is the answer not in the manual?

Questions and answers

Summary of Contents for Multilink 010-505-10

  • Page 1 EDP Transfer Switch Only Series Safety Automatic 010-505-20 120 VAC 60Hz Unive rsal with Transfer Switch Line Interactive PS’ Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 2: Table Of Contents

    Section 6: Shutdown Section 7: Replacement Parts Part List ...............................................15 Section 8: Troubleshooting Section 9: Specifications Parameter Specifications & Notes .....................................17 Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 3: Section 1: Critical Safety Issues

    Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 4: Emergency Shutdown

    3. If using the SATS with a Multilink EDP series UPS, turn off the AC circuit breaker and discon- nect the battery harness from the front of the UPS. The EDP series accepts multiple sources of power and all must be removed to safety shut down the SATS.
  • Page 5: Multiple Power Sources

    If these temperature limits are routinely exceeded or ventilation requirements cannot be attained, a suitable forced-air cooling system may be required within the enclosure. Fig. 1-1 Typical DOT/ITS SATS Enclosure Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 6: Section 2: Introduction

    UPS power loss to allow for AC generator initialization and startup. This allows the output voltage of the generator to stabilize before use. The SATS comes in two models, one which mates specifically to Multilink’s EDP Double Conversion UPS’ , and another universal model which mates to Line Inter- active UPS’ .
  • Page 7: Missing Or Damaged Items

    Missing or Damaged Items If items are found to be damaged or missing, contact the shipping company and your Multilink representative immediately. All damage claims must be filed with the shipping company convey- ing your equipment. Your Multilink representative will be able to assist with immediate equipment needs if necessary.
  • Page 8: Section 3: Front Panel Controls & Connections

    DEDICATED DRY 6.0A DUPLEX HARNESS AND UPS INPUT CIRCUIT CONNECTORS CONTACT RELAYS OUTLET BREAKER Fig. 3-1 SATS Front Panel Detail Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 9: Section 4: Installation And Setup

    Safety ground and earth ground connections must be in place for the SATS and enclosure for both per- sonal safety and operational considerations. During SATS and/or enclosure installation, the following grounding connections must be provided or verified. Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 10: Placement In The Enclosure

    SATS for unobstructed airflow. Temperature of the air entering the SATS should not exceed 74°C (165° F). System de-rating will occur at 55°C. See Specifications. Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 11: Wiring

    3. Wire the SATS as shown in Fig 4-1. Recommended wire strip length of 7mm. Secure the screw termi- nal contacts with a max torque of 7.0Lbf-in. Fig. 4-1 SATS and EP1100 (Line Interactive) wiring example Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 12 2 positions will close. When AC Generator voltage is absent, the dry relay contacts will open. 4. Position 7 is an additional grounding point. Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 13: Section 5: Startup & Operation

    6. Place the UPS Input circuit breaker on the UPS to the OFF position. 7. The UPS and battery string may now be maintained by a qualified technician. Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 14 9. Replace the top cover of the SATS and reinstall the SATS into the cabinet as shown in Section 4. 10. Perform the startup procedure in Section 5. PIN 1 Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 15: Section 6: Shutdown

    4. If a generator is in use, disconnect the generator from the outside cabinet generator connector. Replacement Parts Section 7: Replacement Parts If parts become damaged or lost during operation, replacement parts are available from Multilink. 535-037-10: 7-position terminal block plug. 540-020-10: 2-position jumper .025sq post for JMP-P, JMP-G, and JMP-M.
  • Page 16: Section 8: Troubleshooting

    • Verify switch is in AUTO Mode. • Verify generator AC output voltage is present. MAINS/GEN Sense relays not reporting • F2, F3 open. Replace fuses. Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 17: Section 9: Specifications

    Dry Contact Sense Relays Switching Power Minimum contact rating: Switching Voltage 12VDC 10mVdc, 10μA. Max Switching Current 5.0 Lbf-in max Carrying Current Multilink Inc. 580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com © Multilink Inc. 2020 • All Rights Reserved...
  • Page 18 Multilink, Inc 580 Ternes Ln Scan Elyria, OH 44035 QR for Tel: (440) 366-6966 website. Fax: (440) 366-6802 youtube.com/GoMultilink facebook.com/GoMultilink1 twitter.com/GoMultilink North America Europe, Middle East & Africa Latin & South America Tel: +1 440 366 6966 Tel: +1 440 366 6966...

This manual is also suitable for:

010-505-20

Table of Contents