Sealey SDSPLUS18 Instructions

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. Safety
1.1. eleCtrICal Safety
warNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
Do Not pull or carry the appliance by the power cable.
8
Do Not pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
Do Not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Do Not connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. GeNeral Safety
disconnect the drill from the mains power before changing accessories, servicing or performing any maintenance.
9
Maintain drill in good condition. Check moving parts and alignment and keep drill bits sharp. If necessary use an authorised service
9
agent.
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Wear approved safety eye protection with side shields and a dust mask if drilling generates dust. Rubber gloves are recommended
9
when using outdoors and safety gloves when drilling items such as steel, brick work etc,
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.
9
Use drill in an adequate working area for its function, keep area clean, tidy and free from unrelated materials and ensure adequate
9
lighting.
Prevent body contact with grounded surfaces to avoid electric shock i.e. pipes, radiators, ranges, refrigerators etc.
9
evaluate your working area before using the drill i.e. ceiling, floors and enclosures may contain hidden electrical wires or water piping.
9
Maintain correct balance and footing.
9
The supplementary handle grip should always be attached for use.
9
Keep children and unauthorised persons away from the working area.
9
Secure non stable work piece with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting and ensure the lock-on button is disengaged before use.
9
Use suitable detectors to determine if utility lines are hidden in the work area or contact local utility companies for assistance. Contact
9
© Jack Sealey limited
18mm SDS PluS rotary hammer
750w/230v
Model no:
Wear protective Wear safety
gloves footwear
Original Language Version
SDSPluS18
Wear protective Wear ear
clothing protection
Wear a mask
Recommended fuse rating:
13 amp
SDSPLUS18 Issue 1 24/09/19