Advertisement

Quick Links

SCPRO 4A BL
User Manual
Version1.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BlueLine Digital MKII SCPRO 4A BL and is the answer not in the manual?

Questions and answers

Summary of Contents for Work Pro BlueLine Digital MKII SCPRO 4A BL

  • Page 1 SCPRO 4A BL User Manual Version1.0...
  • Page 2 This document contains essential information on the use of the system. Read this document carefully to become familiar with the system. Please check the WORK PRO website regularly to download the latest version of the document and software updates: https://www.workpro.es/ BLUELINE DIGITAL MKII SERIES www.workpro.es...
  • Page 3: Table Of Contents

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 CONTENT 1. INTRODUCTION ..........................3 2. Components of the BlueLine Digital MKII System ................4 3. RECEIVERS ............................4 Audio extracting methods......................5 3.1.1. DUAL ..........................5 3.1.2. SINGLE ......................... 5 3.1.3. MONO.......................... 6 3.1.4.
  • Page 4: Introduction

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 INTRODUCTION The devices of the BlueLine Digital MKII series allow the streaming of audio over IP through Ethernet, complying with the TCP / IP protocol stack. Using the BlueLine Digital MKII system it is possible to perform from a simple point-to-point audio transmission to a complex multi- channel system with alarm control and management.
  • Page 5: Components Of The Blueline Digital Mkii System

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 2. Components of the BlueLine Digital MKII System In this chapter you will find information about the different devices that make up the BlueLine Digital MKII system. The BlueLine Digital MKII system has four kinds of devices: BLS2 LITE MKII One stereo channel sender STREAMERS...
  • Page 6: Audio Extracting Methods

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 Audio extracting methods It is important to emphasize that each audio receiver is only capable of extracting one stereo audio channel from the network. The extraction of this channel can be done in different ways, that can be select in the configuration interface of WorkCAD3 Configurator.
  • Page 7: Mono

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 3.1.3. MONO Mono extraction mode. The two input channels (1-L and 2-R), are summed to extract them by both outputs of the receiver. 6 dB are subtracted from each output to compensate for the electrical sum of two input channels.
  • Page 8: Invert Out

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 3.1.4. INVERT OUT Inversion of the polarity for output 2, in order to create a balanced output or Bridge I the case of amplified output. This option is only available for SINGLE and MONO modes. In this case, we select MONO mode BLUELINE DIGITAL MKII SERIES www.workpro.es...
  • Page 9: Scpro 4A Bl

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 SCPRO 4A BL SCPRO 4A BL is a stereo one channel audio over IP receiver with included amplifier. With it you can extract one of the channels emitted by the Blueline Digital MKII transmitters. Furthermore, SCPRO 4A BL includes 1x GPI (pull-up) and 1x GPO (open collector).
  • Page 10: Características

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 Características Analog audio output Number of channels 1 stereo channel (unbalanced) or 1 single /mono channel (balanced) Audio connector Euroblock, 3 pin 5.08mm Output sensitivity -1.15 dBu (640mV ), balanced Amplified audio output Power output, dual mode (24Vdc) 2x 20W @ 4 Ω...
  • Page 11: Description Of The Device

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 Description of the device 1. RST. Take the device to its factory configuration 2. LAN. Connection port to local network, RJ45. 3. REMOTE. Port for wallmount controller connection BLC 1 (RJ 45). 4.
  • Page 12: Remote

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 4.2.2. REMOTE This port allows the connection of a BLC 1 wall controller acting as a local command. In this way, it is possible to select the audio source and control the volume. 4.2.3.
  • Page 13: Analogic Audio Output

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 4.2.4. Analogic audio output The device's analog audio output can be balanced or unbalanced depending on the chosen extraction mode. To do this, keep in mind the following connection types: STEREO UNBALANCED MONO UNBALANCED MONO BALANCED 4.2.5.
  • Page 14: Main Supply Input

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 Amplified audio output Power output, dual mode (24Vdc) 2x 15W @ 4 Ω Power output, Bridge mode (24Vdc) 1x 30W @ 8 Ω Power output, dual mode (PoE) 2x 5W @ 4 Ω Power output, Bridge mode (PoE) 1x 10W @ 8 Ω...
  • Page 15: Device Setup

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 Device Setup The configuration of the device must be done through the WorkCAD3 configurator software, which can be downloaded from our website. After configuring the device's IP level and updating it if necessary (See WorkCAD3 Configurator manual), proceed with its configuration.
  • Page 16: Accessories

    SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 • Mono: Audio extraction in mono mode, adding the two channels and extracting it through both outputs with an attenuation of -6 dB. • Channel: Selection of the channel to extract in individual mode.1(L) or 2 (R).
  • Page 17 SCPRO 4A BL MANUAL DE USUARIO VERSION 1.0 BLUELINE DIGITAL MKII SERIES www.workpro.es...

Table of Contents