Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Maxx 20574
- Page 1 Bladblazer Model: 20574...
-
Page 3: Table Of Contents
INTRODUCTION The Back-Pack Blower was designed and manufactured to provide long life and on-the-job-de Read and understand this manual. You will find it easy to use and full of helpful op -pendability. -erating tips and SAFET Y messages. THE OPERATOR'S MANUAL Contains specifications and information for operation, starting, stopping, maintenance, storage and assembly specific to this product. -
Page 4: Safety
Assembly..........................9 -Specifications.........................9 -Install Blower Pipes /Stick Handle................10 Pre-Operation........................12 -Fuel..........................12 Operation..........................14 -Starting Cold Engine.....................14 -Starting Warm Engine....................14 -Stopping Engine......................15 -Operating Blower......................15 Maintenance..........................16 -Skill Levels........................17 -Maintenance Intervals....................18 -Air Filter.........................19 -Spark Plug........................19 Troubleshooting........................20 Storage..........................23 Transporting..........................24 Tool List..........................24... -
Page 5: Decals
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment. SAFETY DECALS Locate these safety decals on your unit. -
Page 6: International Symbols
Symbol Form/shape Read and Symbol Wear ears Keep Wear eyes u n d e r s t a n d bystanders description/ protection Hot Surface protection O p e r a t o r ' s application awway Manual SAFETY INSTRUCTIONS PERSONAL CONDITION AND SAFETY EQUIPMENT WARNING DANGER... - Page 7 physical condition-- Your judgment and physical dexterity may not be good; if you are tired or sick, if you are taking medication, if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye Protection-- Wear eye protection that meets ANSIZ87.1 or CE requirements whenever you operate the machine.
-
Page 8: Equipment
Proper Clothing-- Keep exhaust area clear of flammable Wear coat guarding against poisons, durable d e b r i s . A v o i d c o n t a c t d u r i n g a n d clothing;... - Page 9 Warning of the danger of rotating parts,take Do not operate the machine so long time,Do have a rest after working an hour or finishing care of your hands. The machine is not suitable use for children. the fuel in the fuel tank. Use rakes and brooms to loosen debris before blowing.
- Page 10 Keep A Firm Grip Hold handle with fingers together encircling the Avoid Hot Surfaces handle. During operation, the muffler or catalytic muffler and surrounding cover may become Keep A Solid Stance Maintain footing and balance at all times. Do extremely hot. Avoid contact during and not stand on slippery, uneven or unstable immediately after operation.
-
Page 11: Assembly
ASSEMBLY SPECIFICATIONS 20574 EB955-E EB955 75.6 51.7 51.7 1265 1265 475×385×520... -
Page 12: Install Blower Pipes /Stick Handle
Install Blower Pipes /Stick Handle WARNING DANGER Never perform maintenance or assembly procedures with engine running or serious personal injury may result. 1.Assemble straight pipe with swivel （D） flexible pipe(C). 2.Assemble flexible pipe(C)to elbow(A)on blower. 3.Assemble clamps(B)onto both ends of flexible pipe(C)and tighten. 4.Loosen wing nut(I)completely and expand open, stick handle clamp(J). - Page 13 Accelerator controller SCREW -11-...
-
Page 14: Pre-Operation
PRE-OPERATION FUEL Fuel is very flammable. Use extreme care when Fuel Requirements mixing, storing or handling or serious personal Use only fresh ,clean fuel Mix all fuels with injury may result. premium 2-cycle engine oil at a gasoline/oil Use an approved fuel container. ratio of 30:1 DO NOT smoke near fuel. - Page 15 STARTING THE MACHINE After Refueling- IMPORTANT Wipe any spilled fuel from the unit. Spilled fuel is a leading cause of Move at least 3m from refueling location hydrocarbon emissions. Some states before starting. may require the use of automatic After use- fuel shel-off containers to reduce DO NOT store a unit with fuel in its tank.
-
Page 16: Operation
OPERATION 5.Move choke (E)to run position and if Recoil starter: Use short pulls-only 1/2-2/3 of necessary, restart engine. rope length for starting. Don't allow the rope to snap back in. Always hold the unit firmly. STARTING COLD ENGINE 1. Close Choke-Cold Start. Move choke (B)up to “Cold Start”position. -
Page 17: Stopping Engine
STOPPING ENGINE 1.Move the throttle lever to the idling position and press the stop switch until the engine comes to a complete stop. OPERATING BLOWER WARNING DANGER Always wear safety glasses, hearing protection, a face filter mask and take all safety precautions or serious personal injury may result. -
Page 18: Maintenance
Read the Safety Section on pages 4 and 6 NOTE carefully. Never use a higher speed setting than necessary to perform a task. Remember, the higher the engine speed, the louder the IMPORTANT blower noise. Minimize dust by using blower To avoid engine damage due to over at lower speeds and by dampening material revving, do not bloke blower pipe opening. -
Page 19: Skill Levels
SKILL LEVEL Level1=Easy to do. Most required tools come with unit. Level2=Moderate difficulty. Some specialized tools may be required. Level3=Experience required. Specialized tools are required. We recommend the unit be returned to your Dealer for servicing. -17-... -
Page 20: Maintenance Intervals
MAINTENANCE INTERVALS I=Inspect, C=Clean, R=Replace Component Maintenance Before Daily 3Month 6 Month /System Procedure Every 4 or 90 o r 2 7 0 hours Hours hours Ⅰ/C Ⅰ/C Air Filter I n s p e c t / R” Replace Ⅰ... -
Page 21: Air Filter
IMPORTANT Time intervals shown are maximum. Actual foam filter r e m o v e t w o use and your experience will determine the screws frequency of required maintenance. All recommendations to replace are based on finding damaged or wear during inspection. ( 1 ) R e p l a c e m e n t w i l l b e r e q u i r e d f o r Commer cial use after 600 hours. -
Page 22: Spark Plug
SPARK PLUG 0 . 6 - 0 . 7 m m Remove spark plug, and check for fouling, worn and rounded center electrode. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. Adjust spark plug gap by bending outer electrode. - Page 23 Problem Remedy Cause Engine-starts hard Engine-does not start Engine Fuel at No fuel at F u e l s t r a i n e r Clean Cranks c l o g g e d F u e l Clean l i n e c l o g g e d See your dealer Carburetor...
- Page 24 No spark Spark gap incorrect Adjust 0.65mm S p a r k a t at plug Covered with carbon Clean or replace plug Fouled with fuel Clean or replace Spark plug defective Replace plug Engine Internal engine See your dealer does not problem crank...
-
Page 25: Storage
STORAGE WARNING DANGER Do not store in enclosure where fuel WARNING DANGER fumes may accumulate or reach an open flame or spark. During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or 3. -
Page 26: Transporting
C. Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston reaches the top of its travel and leave it there. 7.Install the spark plug （do not connect ignition cable）. 8. Remove blowy pipe assembly from unit. TRANSPORTING •Allow the engine to cool before transporting. - Page 28 OUR MAXXTOOLS SERVICE TEAM HELPS ONS MAXXTOOLS TEAM HELPT JE MET: YOU WITH: Vragen over je bestelling Questions about your order Klachten Complaints Onderdelen en handleidingen Parts and manuals Heb je vragen of klachten contacteer ons en we helpen je graag verder. If you have any questions or complaints, please contact us and we will be happy to help you.
Need help?
Do you have a question about the 20574 and is the answer not in the manual?
Questions and answers