Summary of Contents for MM-Tech RJQ Series
- Page 1 Plastic Pipe Socket Fusion Tools INSTRUCTIONS ------- RJQ, ZRJQ,ZRJQ-T PORTABLE SERIES 第 1 页 共 17 页...
-
Page 2: Table Of Contents
Contents Brief Introduction ---------------------------------------------------- 1 Technical data ---------------------------------------------------- 2 Product Structure ---------------------------------------------------- 3 Points for attention ---------------------------------------------------- 4 After service ----------------------------------------------------- 5 Guarantee receipt ------------------------------------------------------6 第 2 页 共 17 页... -
Page 3: Brief Introduction
There are 2 series with different size and operation for meeting different customer’s requirement .RJQ series are based on the standard and regular hand-held socket welder with a new controller for overheat protection and easy operation. -
Page 4: Technical Data
Plastic pipe socket fusion tools series comply with the following specification: B. Technical data Table 1 Fusion Tools Surface temperature Time Specification Input volt Frequency Rated watt of welding sockets & specified and Model no. spigots temperature ℃ <min RJQ-40 (110)220/230 (60) 50 600/650... - Page 5 Table 2 Welding Sockets & Spigots Specifications of Internal diameter Internal diameter Heat-fusing depth concave head---Spigots convex head---Sockets pipes (φ ) (φ ) (φ ) 16.04 15.54 15.84±0.04 15.44±0.04 20.05 19.53 19.78±0.04 19.38±0.04 25.04 24.51 24.77±0.04 24.32±0.04 32.03 31.50 16.5 31.75±0.04 31.26±0.04 40.02...
-
Page 6: Product Structure
3. Heat insulation cover 4. Heating plate 5. Electrical wires 6. Additional supporting stand D. RJQ Series-Points for attention 1.The handle shell of the product is strong and reliable, the electric wires are standard with grounding 第 6 页 共 17 页... - Page 7 safety plug. Please insert the plug into the safe outlet when using the tool. The plug shouldn’t be changed arbitrarily. 2. In order to protect the safety of persons and property, make sure to place the tool safely when it works normally.
- Page 8 7.If the electric wires are broken, it should be changed in the appointed maintenance store or distributor because it needs special tools. 8.When you finished the fusing work, you must pulled out the plug first, and after the tool becomes cool, put it back to the box.
- Page 9 11.Switch on the power and heat: Switch on the power (Warning: the power should have the grounding wire!!!), then the red indicator lamp will be on. That means the fusion tool is being heated. When the red lamp is off and the green indicator lamp is on, it means the fusion tool stops heating. After a while, the red lamp will be on again and the fusion tool is in a state of keeping temperature and ready to work.(the process is often less than ten minutes.) 12.Fusing and connecting pipes: Use pipe cutter to cut pipes vertically.
- Page 10 Table 3 Fusing Standards for Plastic Pipes & Fittings Fusing depth External diameter of Heating time Processing time Cooling time (mm) pipes (mm) (min) （2） （2） （2） （6） 16.5 18.0 第 10 页 共 17 页...
- Page 11 （4） 20.0 （8） 24.0 （6） 26.0 （6） 29.0 32.5 Note: If the surrounding is lower than 5℃, the heating time should be extended 5%. E. ZRJQ Series- Product Structure 1. Handle shell 2. Digital controller with temperature display screen including following keys: “RDY”...
- Page 12 6.Additional supporting stand F. ZRJQ Series-Points for attention 1. The suggestion temperature for below pipe: PP-R 260℃ 240℃ HDPE 250℃ 2. Set the temperature: First press the key “SET” , it will display the original set temperature and with flickering on the unit figure(0-digit), and if you press “Up “key or “Down”...
- Page 13 the unit and decimal figure. Temperature range is fixed, Maximum. is 279℃, Minimum is 200℃, after finish the temperature setting, please press the “SET” key once again, then the tool is ready to work. 3. Over-heating alarm When the tool make the buzz , it warns the temperature over 295℃, and you must switch off the power.
-
Page 14: After Service
6.The set temperature before sales This tool is set temperature 260℃ before sales. 7. Other attention points are same as RJQ series tools. After service All series of portable socket fusion tool are safe, convenient, practical and reliable.It is guaranteed for one year. - Page 15 cost price. If you want to have further service, you can contact local agent or manufacturing factory. The users who without any agent in the locality can post the broken parts to the factory. The factory will bear all the charges within six months but charge the cost fee and postage after six months.
-
Page 16: Guarantee Receipt
H.guarantee receipt Guarantee receipt of plastic pipes fusion tools Customer’s name_____________ Tel.___________________ Purchase date __________________ Address________________________ Purchase place____________________ Specification______________________ Suggestions and evaluation of the product________ 第 16 页 共 17 页... - Page 17 WIDOS Wilhelm Dommer Söhne GmbH Einsteinstr. 5 71254 Ditzingen – Heimerdingen Tel.: +49 (0) 7152/9939-0 Fax: +49 (0) 7152/9939-40 info@widos.de www.widos.de 第 17 页 共 17 页...
Need help?
Do you have a question about the RJQ Series and is the answer not in the manual?
Questions and answers