Page 1: Table Of Contents
5 Required tools 6 Install the TrafficLink Antenna 6 Install the SmartLink (travel time only) 7 Install the SmartLink with a TrafficLink Interface 8 Install the SmartLink 8 Install the TrafficLink Interface ABC 9 Install the TrafficLink Interface EF-140 10 ...
Page 2: Package Contents
● NEMA collar connector screws - for tight installations that require shorter screws ● For SDLC installations, Y cable. MioChuck tool Cabinet clip For travel time-only installations: ● No TrafficLink Interface is required. 6.11.19 2 ...
Page 3 For NTCIP controllers: ● If the controller in your cabinet uses NTCIP over Ethernet to connect the SmartLink, the TrafficLink Interface is not required. However, you will need to determine the IP settings for your installation. Contact C ustomer Support...
Page 4: Safety Recommendations
If your application requires a TrafficLink Interface ABC device, the package also contains: ABC cables A Cable B Cable TrafficLink Interface ABC C Cable If your application requires a SmartLink SDLC, the package also contains: ...
Page 5: Before You Begin The Installation
Before you begin the installation Plan component locations Before you begin, determine the best location for the TrafficLink Antenna, SmartLink, and TrafficLink Interface (if necessary). You might need to move some of the existing equipment in the cabinet to accommodate the devices. ...
Page 6: Required Tools
If you cannot install the SmartLink next to the TrafficLink Interface, install them no more than 1.2 m (4 ft) apart. Use caution when moving components to avoid disconnecting cables. Make sure that you have access to terminal block wiring or an 110V-240V uninterrupted ...
Page 7: Install The Smartlink (Travel Time Only)
12. Visually inspect the antenna to make sure that the adhesive forms a tight seal on top of the cabinet. Follow the procedure that matches your installation scenario: Install the SmartLink (travel time only) ● Install the SmartLink with a TrafficLink Interface ● Install the SmartLink without a TrafficLink Interface ●...
Page 8: Install The Smartlink With A Trafficlink Interface
TrafficLink. Install the SmartLink with a TrafficLink Interface Installing a TrafficLink Interface ABC or TrafficLink Interface EF-140 requires putting the intersection into flash. If you prefer to review these steps in a video tutorial, see SmartLink installation...
Page 9: Install The Trafficlink Interface Abc
Connect the TrafficLink Interface to the power supply (terminal block wiring or 110V-240V non-GFCI) and then turn on the TrafficLink Interface. Verify that the TrafficLink Interface power LED is solid green. If it is not, check the cable connections. Return the intersection to its normal operating mode. ...
Page 10: Install The Trafficlink Interface Ef-140
Attach the ABD cables to the corresponding inputs on the controller. Connect the TrafficLink Interface EF-140 to the power supply. Verify that the TrafficLink Interface power LED is solid green. If it is not, check the cable connections. Return the intersection to its normal operating mode. ...
Page 11: Install The Smartlink Without A Trafficlink Interface
5. If the controller supports Ethernet connections, obtain and document the IP address of the controller in the installation checklist. The SmartLink takes a few minutes to connect to the TrafficLink software. You can continue installing other components while the SmartLink is connecting. ...
Page 12 SmartLink. If the controller supports Ethernet connections, obtain and document the IP address of the controller. The SmartLink takes a few minutes to connect to the TrafficLink software. You can continue installing other components while the SmartLink is connecting. ...
Page 13: Connect Optional Components
Serial Port 4. Complete the installation Perform a final review of the cabinet 1. Before closing the cabinet door, verify that the TrafficLink Antenna is securely fastened. 2. Confirm that the LEDs on SmartLink appear as follows: ...
Page 14: Document The Location Of The Trafficlink Components
. Document the location of the TrafficLink components After you install the TrafficLink components, take the following photos to record the component locations. The photos will be uploaded to TrafficLink. 1. Take a photo of the inside of the traffic cabinet showing the placement of the ...
Page 15 TrafficLink 265 mm 100 mm 246 mm 2.20 kg Interface ABC (10.43 in) (3.94 in) (9.69 in) (4.85 lb) TrafficLink 265 mm 100 mm 246 mm 2.02 kg Interface (10.43 in) (3.94 in) (9.69 in) ...