Advertisement
DO NOT touch the quartz lamps, even when cold. (See 3.1.4).
7
DO NOT use the heater without the guards fitted.
7
DO NOT use the heater without the wheels fitted and locked.
7
DO NOT allow the heater to get wet as this may cause an electric shock, causing damage to the heater and possible personal injury.
7
DO NOT let power lead hang over an edge (i.e. table), or touch a hot surface, lie in the beam of heat, or run under a carpet.
7
DO NOT cover heater when in use, and do not obstruct the air inlet and outlet grilles.
7
DO NOT use in bathroom, shower room, or in any wet or damp environments or where there is high condensation.
7
DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT insert or allow objects to enter any openings of heater as this may cause an electric shock, fire or damage to heater.
7
DO NOT use the heater out of doors. These heaters are designed for indoor use only.
7
DO NOT use heater if the power cord, plug or the heater is damaged, or if the heater has become wet.
7
DO NOT use the heater where there are flammable liquids, solids or gases such as petrol, solvents, aerosols etc, or where heat sensitive materials may be stored.
7
DO NOT place the heater near items that may be damaged by heat, allow at least 2mtr clearance in front of the heater.
7
DO NOT touch the outlet grille of the heater during and immediately after use as it will be hot.
7
DO NOT allow children to touch or to operate the heater.
7
DO NOT place heater too close to yourself or any object, allow the air to circulate freely.
7
DO NOT use the heater for any purpose other than for which it is designed.
7
Allow the unit to cool before storage. When not in use, disconnect from the mains power supply and store in a safe, cool, dry, childproof area.
3
2.
INTRODUCTION AND SPECIFICATIONS
2.1.
Introduction
2.1.1. Powder coated metal cabinet with 2 quartz infrared lamps and chemically polished reflectors for maximum heat emission. Controllable power output by
rocker switches on the side of the cabinet. Features easy-rolling swivel castors with 2 locking castors. Suitable for wide range of personnel warming
and restorative applications. Supplied with cable and BS/ASTA approved plug.
2.2.
Specification
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IRC153.V3 . . . . . . . . . . .IRC153.110V.V2 . . . . . . . . . . . . . . . .IRS153.V3 . . . . . . . . . . .IRS153.110V.V2
Power output (2 heat settings) . . . . . . .1500/3000 Watt
Size W X D X H . . . . . . . . . . . . . .560 x 490 x 880mm . . . . . . . . .560 x 490 x 880mm . . . . . . . . .590 x 500 x 820mm . . . . . . . .590 x 500 x 820mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18kg . . . . . . . . . . . . . . . . . . . .18kg . . . . . . . . . . . . . . . . . . . .13kg . . . . . . . . . . . . . . . . . . . .13kg
Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V (50Hz) . . . . . . . . . . . . . .110V (50Hz) . . . . . . . . . . . . . .230V (50Hz) . . . . . . . . . . . . . .110V (50Hz)
Spare lamp Part No. INF64241565
3.
ASSEMBLY
3.1.
IRC153.V3 - IRC153.110V.V2 Fig.1.
3.1.1. Attach the wheel sub-assemblies to
the base of the heater using the bolts
provided. Ensure the lockable wheels
are to the rear of the heater.
3.1.2. Attach the handle to the top of the
heater using the bolts provided,
ensuring the shaped spacers are
fitted between the heater and the
handle as shown.
3.1.3 Remove the front grille by
unscrewing the retaining screws.
3.1.4 Extract the lamps from the shipping
carton.
NEVER TOUCH LAMP GLASS
DIRECTLY WITH FINGERS, ONLY
TOUCH THE CERAMIC ENDS OR
USE A SOFT CLOTH,
OTHERWISE LAMPS COULD BE
DAMAGED!
3.1.5 Carefully insert each lamp into the
two push-in side fittings with a
gentle pressure.
3.1.6 Check the lamps are properly located.
3.1.7 Reassemble front grille.
4.
HEATER OPERATION
4.1.
Operating the heater.
4.1.1. Place the heater on a level floor in a suitable position in the area you require to heat. Allow a minimum of 2mtr between the heater and adjacent objects.
4.1.2. Plug the heater into the mains supply.
4.1.3. Select the required output by using the two rocker switches on the side which switch the lamps on and off. Each lamp has an output of 1500W.
4.1.4. To switch the unit off, select “0” on both the rocker switches and unplug from the mains. Allow the unit to cool before handling or storage.
WARNING! DO NOT touch the top of the heater when in use as it becomes hot.
p
WARNING! Always allow lamps to cool before moving the units. Use only on a smooth even surface. Failure to do so will cause premature wear to
p
p
the lamps and reduce their working life.
. . . . . . . . . . .1500/3000 Watt . . . . . . . . . . . .1500/3000 Watt . . . . . . . . . . . .1500/3000 Watt
Fig 1
3.2.
IRS153.V3 - IRS153.110V.V2 Fig.2.
3.2.1. Fit the handle section of the
support frame to the wheel
section ensuring the fixing holes
align.
3.2.2. Fit the heater to the support frame
using the bolts provided, ensuring the
shaped spacers are fitted either side of
the frame as shown. Tighten the
bolts sufficiently to retain the heater
at the required angle.
3.2.3 Remove the front grille by
unscrewing the retaining screws.
3.2.4 Extract the lamps from the shipping
carton.
NEVER TOUCH LAMP GLASS
DIRECTLY WITH FINGERS, ONLY
TOUCH THE CERAMIC ENDS OR
USE A SOFT CLOTH,
OTHERWISE LAMPS COULD BE
DAMAGED!
3.2.5 Carefully insert each lamp into the
two push-in side fittings with a
gentle pressure.
3.2.6 Check the lamps are properly located.
3.2.7 Reassemble the front grille.
IRC153.V2, IRC153.110V, IRS153.V2, IRS153.110V - 1 - 010704
Fig 2
Advertisement
