Advertisement
Quick Links
Advertisement
Summary of Contents for SynQe gSmart8900
- Page 1 Quick View Guide...
- Page 2 Appearance Introduction...
- Page 5 Component Serial No. Illustration Element The green light flickers when opening the telephone module. LED indicator The red light flickers when low battery. light The red light/green light is on when being charged/full charge. The red light flickers if missing calls. Long Press: turn on or off the device.
- Page 6 It fixes the battery with a RFID Battery Cover antenna stuck inside. used clicking corresponding area of the screen in Stylus order to fulfill the corresponding functions. Screw of hand It fixes the hand belt support. belt support Hand belt It fixed the hand belt support.
- Page 7 cover of the device to the left in order to separate the back cover and the device. Take out the battery by pulling the battery belt. Installation of TF card: push the locker of SIM card to the left and uplift the locker of SIM card from the right side, then push the locker of TF card to the upside and uplift the locker of TF card from the downside, next put TF card in the locker (be noted that...
- Page 8 terminal), finally put down the locker of TF card and push the locker to the downside. Installation of SIM card: push the locker of SIM card to the left and uplift the locker of SIM card from the right side, then put SIM card in the locker (be noted that the metal sheet of SIM card shall face the metal contactor at the terminal), finally put down the locker of SIM card and push the locker to the downside.
- Page 9 be faced to the metal contactor at the terminal; ensure the contactor of the battery is aligning at the connecting terminal of the battery. Then, push the battery to the locked position. Installation of the back cover: close the back cover and push the locker of the back cover of the battery to the right side and finally lock the back cover.
- Page 10 Battery Charging The new accessory battery is entitled with only part electric quantity, so the battery must be charged before using. Normally, the battery will reach the optimal performance after full charging and discharging for two or three times. There are two ways of charging the battery: ●...
- Page 11 Power button for 5 seconds to implement power-on order. Turn off the device Under the status of starting up, long press Power button for over seconds and release, then the screen illuminates and an interface pops out: ● power-off: the device will be turned off if choosing this. turn off phone function: turn off phone and then quit the procedure according to the current phone status;...
- Page 12 The way of releasing screen lock: slide to the left or the right to release screen lock according to the tip. Today Interface When you turn on the device each time, the device enters into “Today Interface”. It is shown in the below picture. Today Interface shows all important information related to the same day, and you can click the corresponding area to turn on the associated procedures.
- Page 13 Notice: You can change the contents shown in “Today ] [set up] [main screen]. Interface” by setting up in [ Start Menu ] menu uses the icons aligned in hexagon to browse software and respond to the stylus pen, such as click and refresh.
- Page 14 When using this mobile phone, you can switch from one program to the other instead of starting up the new program on the basis of terminating the using program. You can switch over programs as follows: ● Click [ ] icon at the bottom left side and opt in the Start menu.
- Page 15 quit the using application program. Status Bar Status bar mainly shows the titles of the application programs that are currently using and the icon notification of status information of the system. The status bar is shown as follows: ● Long press the status bar and the hidden tool bar will appear. The tool bar includes: search, feedback, synchronization, phone, voice, battery, clock and alarm clock.
- Page 16 Vibration mode Disconnected. connected the network. Available wireless network is detected. Wi-Fi network. Connecting to WI-FI. GSM network. EDGE network. 3G network. WCDMA network. Wi-Fi The effective distance of this device is relatively long, as long as 180m. Wi-Fi, full name Wireless Fidelity, also called 802.11b/g Standard, is an industrial standard defined by IEEE for wireless network communications.
- Page 17 To establish connection with the encrypted AP. Select MobileXP-Dlink>[Connection] to start setting (AP with strong signal is recommended) >[Next].
- Page 18 Due to different encryption of Wi-Fi, clear the option of automatically providing password, input password in [Network Password] >[Next] >[Finish]. When Wi-Fi is automatically connected to MobileXP-Dlink, if the connected AP connects with the external network, you can use IE to browse websites. If establishing connection with unencrypted AP, select [buffalo]-[testing]-[Connection].
- Page 19 Application of General Scan Select [GeneralScan] in the application programs, or click [ ] [explorer] [programs file] [ScanDemo] [GeneralScan], then the screen will show the following picture:...
- Page 20 Now press Scan button and aim at the scanned label, then the interface will show the corresponding information contents of the label. Click [Clear] and information in the interface will be cleared. Click [Exit], and quit the application and then return to the main interface. RFID Scanning Select [MifareDemo] in the application programs, or click [ ]...
- Page 21 Put the scanned label close to the back of the mobile phone, press [OpenPort] to open the port, then press [Request] to send the request of reading card. If press [Card ID] when unread to read the ID number of the label, the ID number will appear at the right side of the interface.
- Page 22 following: Phone Click and enter into the dialing tray, and input the numbers for dialing. Click and enter into the list of SMS. Contact Click and enter into the list of contacts. Email Click and enter into the list of emails. Multi-media Click and enter into the table of multi-media, including music play, picture and video, radio, camera and flow...
Need help?
Do you have a question about the gSmart8900 and is the answer not in the manual?
Questions and answers