1. Manuals
  2. Brands
  3. The Handy Manuals
  4. Cutter
  5. THMC
  6. Owner's manual

The Handy THMC Owner's Manual

Multicutter
Hide thumbs
Table of Contents

Advertisement

Quick Links

CONTENTS
Page 2
3
4
5
6-7
8-12
13-14
15
16
17
18-22
23

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the THMC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for The Handy THMC

  • Page 1: Table Of Contents

    CONTENTS SAFETY INSTRUCTIONS SPECIFICATIONS FUEL MAJOR PARTS ASSEMBLY 8-12 REPLACEMENT OF SPOOL, LINE AND CHAIN 13-14 OPERATION MAINTENANCE TROUBLE SHOOTING PARTS DIAGRAMS AND LISTS 18-22 EC DECLARATION OF CONFORMITY Page 2...

  • Page 2: Safety Instructions

    SAFETY INSTRUCTIONS Read and understand the owner’s manual and labels affixed to the multicutter. Learn its application and limitations as well as the specific potential hazards. Retain these instructions for reference. • Use sturdy footwear and a helmet with eye and ear protection. Protect exposed parts of your body.

  • Page 3: Specifications

    SPECIFICATIONS MODEL THMC Engine Displacement 25.4cm³ 0.75Kw/7800 minˉ¹ Max Output Power Fuel Tank Capacity 0.6L Bore and Stroke 34 x 28mm Fuel Type Unleaded Fuel Mixture Unleaded Petrol/Oil 25:1 Mineral Oil (see below for synthetic) Equivalent Spark Plug Champion RCJ6Y or NGK BPMR7A...

  • Page 4: Fuel

    FUEL Petrol is very flammable. Do not use or fuel the multicutter near a flame, sparks or while smoking. Allow the engine to cool before re-fuelling. Fuel the engine at least 3m away from your work area. • se a ratio of 25:1 unleaded petrol to mineral oil. Mix well in an appropriate mixing bottle.

  • Page 5: Major Parts

    MAJOR PARTS   Page 6  ...
  • Page 6 MAJOR PARTS Description Description Hedgetrimmer Cutting Blade Throttle Lock Button Gear Head Fuel Tank Cap Locking Screw Heat Insulation Protector Locking Knob Sprocket Wheel Cover Adjusting Bracket Guide Bar Nut Assistant Gear Head Sprocket Special Spanner Guide Bar Stud Pruner Gear Head Oil Ducts Upper Shaft of Engine Chain Tensioner...

  • Page 7: Assembly

    ASSEMBLY Modern production techniques mean that there is very little likelihood of there being any parts missing in the carton supplied. However please check the box carefully before commencing any assembly. If you are missing any parts please call our spares helpline: 01793-333212. Contents: Power Unit;...
  • Page 8 ASSEMBLY, cont’d Hedgetrimmer Attachment: • Locate the bracket on the plane of the gear head and position the locking screw (3) through the adjusting hole in the bracket. • Use the two Screws (25) and flat washer (26) to attach the bracket to the gear head. •...
  • Page 9 ASSEMBLY, cont’d  Brushcutter Attachment: Fig. 1 Remove the Blade Nut, this nut has a left hand thread so should be turned clockwise to undo it. Fig. 2 Remove the Cupped Washer, Clamp Washer and Flanged Washer. Fig. 3 Remove the 3 Blade Guard Screws with the Allen key. Fig.
  • Page 10 ASSEMBLY, cont’d Operating the Brushcutter: • Operate the throttle trigger with your right hand and hold the barrier handle with your left hand. • Always keep a firm grip with both hands during operation. • The brushcutter should be held at a comfortable position with the trigger handle about hip height.
  • Page 11 ASSEMBLY, cont’d Line Trimmer Attachment: • Slide the shield onto the attachment shaft and fit over the bracket, as in Fig. 11. • Fix the bolt through the holes in the tabs on the shield and the slots in the bracket on the attachment shaft. •...

  • Page 12: Replacement Of Spool, Line And Chain

    REPLACEMENT OF SPOOL AND LINE To replace the line or spool: • Stop the engine. • Lay the trimmer on the floor so that the cutting head is facing up. • Remove the bump knob/retaining cap by turning it anti-clockwise. •...
  • Page 13 REPLACEMENT OF PRUNER CHAIN • Remove the sprocket wheel cover (34). • Remove the guide bar and chain. • Remove the old chain and replace with the new chain. • Mount the guide bar and then fit the saw chain around the bar and sprocket, paying particular attention to the correct direction of the chain.

  • Page 14: Operation

    OPERATION Starting the Multicutter: • Move the ignition switch to the “on” position (Fig. O). • Move the choke lever upwards to the “start” position (for cold start only) (Fig. P). • Push the primer bulb 10 times until the petrol/oil mixture fills the primer bulb (Fig. Q). •...

  • Page 15: Maintenance

    MAINTENANCE The engine of the multicutter must be at a complete stop during assembling, cleaning and any maintenance that may be necessary. Air Filter: Accumulated dust in the air filter will reduce engine efficiency, increase fuel consumption and allow abrasive particles to pass into the engine. Remove and clean the air filter regularly to ensure optimum performance.

  • Page 16: Trouble Shooting

    TROUBLE SHOOTING  PROBLEM POSSIBLE CAUSE SOLUTION Power loss or sudden Fuel Tank is empty. Add fuel. stopping. Mixture not reaching Drain and rinse out fuel carburettor. system. Water in the mixture. Clean fuel filter. The air filter is dirty. Clean air filter. Carbon deposits in Clean all affected parts cylinder, exhaust pipe...

  • Page 17: Parts Diagrams And Lists

    PARTS DIAGRAM AND LIST - ENGINE Part No Desc Qty No Part No Desc TH132-1 Screw TH132-25 Flat Washer TH132-2 Spring Washer TH132-26 Heat Shield TH132-3 Flat Washer TH132-27 Exhaust TH132-4 Filter Housing TH132-28 Exhaust Gasket TH132-5 Carburettor TH132-29 Clips TH132-6 Gasket TH132-30...
  • Page 18 PARTS DIAGRAM AND LIST - LINE TRIMMER (THLTATT) Line Trimmer Parts: Part No Description TH131-2 Bracket TH131-3 Screw TH131-4 TH131-6 Spool & Cap Assembly TH131-7 Shield TH131-8 Knob TH131-9 Washer Page 19...
  • Page 19 PARTS DIAGRAM AND LIST - BRUSHCUTTER (THBCATT) Part No Description TH130-1 Shield TH130-2 Flat Washer TH130-3 Spring Washer TH130-4 Screw TH130-5 Blade Boss Outer TH130-6 Nut Cover TH130-7 Lock Nut (Left Hand) TH130-8 Blade Boss Inner Page 20...
  • Page 20 PARTS DIAGRAM AND LIST - HEDGETRIMMER (THHTATT) Part No Description TH128-1 Angle Bracket Assy TH128-2 Blade Assembly Page 21...
  • Page 21 PARTS DIAGRAM AND LIST - PRUNER (THPATT) Part No Description TH129-1 Oil Filler Cap TH129-3 Fuel Tank Assembly TH129-4 Chain HP-166 TH129-5 Chain Bar TH129-6 Chain Bar Cover TH129-7 TH129-8 Chain Cover TH129-9 Chain Tension Adjuster Assy Page 22...

  • Page 22: Ec Declaration Of Conformity

    - Machinery Directive 98/37/EC - Noise Emissions Directive 2000/14/EC Handy Distribution Ltd hereby declares that the product: Machine Type: 25cc Multi Cutter Machine Model: THMC Net Installed Power: 0.75Kw Mass in Kg: 11Kg Cutting Capacity: 205mm Brushcutter; 381mm Line Trimmer; 250mm Pruner;...
  • Page 23 To order spare parts and see the complete range of garden machinery and garden equipment from Handy, visit: www.thehandy.co.uk Spares & Support: 01793 333212...

Table of Contents