Related Manuals for HYCON HY17M24 Series
Summary of Contents for HYCON HY17M24 Series
- Page 1 HY17M24 Series IDE Hardware User’s Manual © 2019 HYCON Technology Corp. Preliminary APD-HY17MIDE002-V01_EN www.hycontek.com...
-
Page 2: Table Of Contents
Control Box Introduction ........................7 4.3. Introduction to Target Board ........................8 4.4. Target Board Circuit Diagram ......................11 4.5. Control Box and Target Board Hardware Connection Steps .............. 12 REVISIONS ............................. 13 © 2019 HYCON Technology Corp Preliminary APD-HY17MIDE002-V01_EN www.hycontek.com page2... - Page 3 HY17M24 Series IDE Hardware User’s Manual Attention: 1、 HYCON Technology Corp. reserves the right to change the content of this datasheet without further notice. For most up-to-date information, please constantly visit our website: http://www.hycontek.com 2、 HYCON Technology Corp. is not responsible for problems caused by figures or application circuits narrated herein whose related industrial properties belong to third parties.
-
Page 4: Package Contents
Model No. Part Name Description Quantity HY17M24-AM01 HY17M24-ES28 Target Board HY17M00-CM01 HY17M00 Control Box HY17M24-DK01 Cable line USB Type A to Mini B Cable Interface line 5pin/2.54 (2.54mm pitch) Table1-1 © 2019 HYCON Technology Corp Preliminary APD-HY17MIDE002-V01_EN www.hycontek.com page4... -
Page 5: Safety Precautions
When following status occurred, please remove the power supply immediately, and contact our engineer. Power Supply line is worn or damaged. Power source (battery) connected but no any light on while operating. Component off. © 2019 HYCON Technology Corp Preliminary APD-HY17MIDE002-V01_EN www.hycontek.com page5... -
Page 6: Software Installation Requirements
(FW version applicable to HY17M00-CM01 is W17M01.4 or above) (4) Supported software version: HY17M IDE V1.2 above: HY17M Series Assembly Language IDE software H08 CIDE V1.1 above: HYCON 8-bit MCU C Language IDE software (5) Supported Operating system: Windows XP, Windows Vista, Windows 7, Windows 8, Windows 10... -
Page 7: Description Of The Hardware
Green LED,When the USB Port is connected to a computer or an external 5V power supply, the L1 light indicates that the Control Box is powered. Error Red LED (reserved, no use). Busy Yellow LED (reserved, no use). © 2019 HYCON Technology Corp Preliminary APD-HY17MIDE002-V01_EN www.hycontek.com page7... -
Page 8: Introduction To Target Board
Target Board being changed and affecting normal development. 4.3. Introduction to Target Board The Target Board (Model No.: HY17M24-AM01) is commonly used in the HY17M24 series (Appearance shown in Figure 4-3), this Target Board can be used in addition to IDE... - Page 9 Description: Pin are defined as follows Name Description VDD_ICE Target Board Chip’s VDD power is coming from Control Box Target Board Chip’s VDD power VDD_IN Target Board Chip’s VDD power is coming from external VDD_EXT power © 2019 HYCON Technology Corp Preliminary APD-HY17MIDE002-V01_EN www.hycontek.com page9...
- Page 10 UART’s receive pin UART’s transform pin Note：The above only describes the basic functions that the Target Board will use, for other unlisted parts, please refer to the circuit diagram or contact FAE technical support. © 2019 HYCON Technology Corp Preliminary APD-HY17MIDE002-V01_EN www.hycontek.com...
-
Page 11: Target Board Circuit Diagram
Note：This Target Board circuit diagram " HY17M24-AM01_Target Board_A19007 V02.pdf " is placed in the IDE software directory and can be referenced by yourself. * If using Assembly IDE, it’s placed in “HYCON\HY17M IDE\Schematic " directory. * If using H08 C IDE, it’s placed in “HYCON\H08 CIDE\ICESchematic\HY17M24" directory. - Page 12 Step3: Use the USB Cable to connect to the Control Box’s USB Port and the computer's USB port (the L1 LED will light up). Step4: After Step 1~3 (as shown in Figure 4-5), the hardware connection is completed. Step1 Step3 Step2 Figture 4-5 © 2019 HYCON Technology Corp Preliminary APD-HY17MIDE002-V01_EN www.hycontek.com page12...
-
Page 13: Revisions
HY17M24 Series IDE Hardware User’s Manual 5. Revisions The following describes the major changes made to the document, excluding the font and punctuation changes. Version Page Date Revision Summary 2019/11/27 First edition © 2019 HYCON Technology Corp Preliminary APD-HY17MIDE002-V01_EN www.hycontek.com page13...
Need help?
Do you have a question about the HY17M24 Series and is the answer not in the manual?
Questions and answers