Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Artusi Manuals
  4. Indoor Furnishing
  5. Alfresco ABS1
  6. Assembly manual

Artusi Alfresco ABS1 Assembly Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
AP PL I ANC ES
FOR L IV ING
ALFRESCO KITCHEN
ABS1 &ABS2
ASSEMBLY MANUAL

Advertisement

loading
Need help?

Need help?

Do you have a question about the Alfresco ABS1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Artusi Alfresco ABS1

  • Page 1 AP PL I ANC ES FOR L IV ING ALFRESCO KITCHEN ABS1 &ABS2 ASSEMBLY MANUAL...
  • Page 2 WHAT TO EXPECT IN THE BOX IMPORTANT - PLEASE CHECK FOR ANY DAMAGED ASSEMBLY PARTS OR COMPONENTS BEFORE ASSEMBLY AND CONTACT ARTUSI IMMEDIATELY. ASSEMBLY REQUIRES 2 PEOPLE MINIMUM. !CONTENTS ARE HEAVY! KNOWLEDGE OF TOOLS AND CORRECT USE IS REQUIRED FOR ASSEMBLY • Right hand side Cabinet Panel (1)
  • Page 3 Right hand side Left hand side Cabinet Door Cabinet top support Cabinet Panel Cabinet Panel brace ref. #1 ref. #2 ref. #3 ref. #5 Cabinet Base ref. #4 Neolinth Stone benchtop with BBQ and sink hole ref. #13 or Neolinth Stone benchtop with BBQ hole (1) ref. #13 Rear vanity panel with breathing slots (1) ref. #14 Right hand side drip Left hand side drip tray tray slider slider ref. #6 ref. #7 Right hand bookend side Left hand bookend side Neolinth Stone leg Neolinth Stone leg ref.
  • Page 4 ASSEMBLY Step 1 • Cabinet Top Support Brace #5. • Use two x M8 dome cap bolts with flat washers. • To attach the door, fit the hinges and the handle (screws not supplied). ASSEMBLY Step 2 • Attach the Right Hand Side Cabinet Panel #1 with the hole facing top to the Cabinet Top Support Brace #5 • Use two x M8 dome cap bolts with flat washers.
  • Page 5 ASSEMBLY Step 3 • Ensure all edges of above components are flush with corresponding edges once tightened. ASSEMBLY Step 4 • Turn the cabinet upside down and mount the base component #4 to the left and right hand side panels. • Use four x M6 dome cap bolts with 1 x flat washer each. Bottom of door This is the underside Bottom of side panels of the cabinet base...
  • Page 6 ASSEMBLY Step 5 • Place vanity panel #14 upside down and attach to the left and right hand side cupboard panels which must also be upside down. • Use four x M8 dome cap bolts with 1 x flat washer each. Indicates where bolts are required for fixing Bottom of cabinet Top of cabinet Bottom of cabinet Top of cabinet...
  • Page 7 ASSEMBLY Step 6 • Rotate assembled components, above, till they’re in the correct upright position. The adjustable feet of the base panel will not be on the floor. Adjust feet to touch floor. Bottom of cabinet Top of cabinet...
  • Page 8 ASSEMBLY Step 7 • Line up the vanity panel #14 within the ‘U’ channel of the right hand side leg #11 ensuring the top of the vanity panel lines up with the top of the leg. Vanity panel #14 to slide into the groove here on the book end legs Step 8 Tighten leg to panel using M8 bolts Step 9 Ensure that the top of the vanity panel is in line with the top groove on the leg Vanity panel and legs must be square. Raise feet to keep in place • Repeat instructions 7 & 8 using the left hand side leg #12.
  • Page 9 ASSEMBLY Step 10 • Install rear drip tray slider #9 to vanity panel using four x countersunk M8 bolts - no washers Step 11 • Install Right Hand Side Drip Tray Slider #6 to left hand side cupboard panel using two x M6 countersunk bolts - no washers...
  • Page 10 ASSEMBLY Step 12 • Place Ceramic Top component #13 onto locating pins on each leg (3 on the top of each leg). • Ensure top edges are lined up with the legs edges and fasten the top using three x M8 dome cap bolts and one spring washer for each bolt.
  • Page 11 ASSEMBLY Step 13 • Install Left Hand Side Drip Tray Slider #7 to top of left hand side leg using two x M8 dome cap bolts and 1 x washer each...
  • Page 12 ASSEMBLY Step 14 • Fix ventilation panel/heat shield #10 to underside of the top on the front using three x M8 dome cap bolts and flat washers...
  • Page 13 ASSEMBLY Step 15 • Fasten side of ventilation panel to left hand side cupboard panel using one x M6 dome cap bolt and flat washer Complete this step on both side of the ventilation panel Ensure this bolt is fitted correctly as this will ensure the structural integrity of the cabinet...
  • Page 14 ASSEMBLY Step 16 • Slide drip tray #9 into position...
  • Page 15 ASSEMBLY Step 17 • Install the door handle to the cupboard door using two x dome cap M4 screws and flat washers.

  • Page 16: Warranty Card

    Warranty Card artusi.com.au The stone bench carries a warranty of 25 years, underwritten by Neolith. All steel elements carry a warranty of 5 years against material failure. What happens if there is a problem? Worldwide Appliances Pty Limited If, when you un-box your item/s there is an issue A.B.N. 45868077422 with any of the pieces, please contact Artusi Office: immediately before assembling the product and parts. 48-50 Moore Street, Leichhardt N.S.W 2040 Post: Locked Bag 3000, Annandale, N.S.W 2038 Artusi will examine the product and decide if it’s covered under the standard product warranty. P: 1300 694 583 Artusi reserves the right to, either repair the WARRANTY REGISTRATION...

  • Page 17: Warranty Registration Card

    Warranty Card continued artusi.com.au Warranty Card tear off WARRANTY REGISTRATION CARD Please complete and send to ARTUSI at: R EPLY PAID 83617 LEICHHARDT NSW 2040 121219 Last Name: First Name: Address: State: Postcode: Email: Home Phone: Mobile: Purchase Date: / / (Please attach proof of purchase to validate warranty) SERIAL NUMBER MODEL NUMBER (if you cannot locate the serial number please call ARTUSI on 1300 694 583) 121219...
  • Page 18 Product dimensions indicated in our literature is indicative only. Actual product only should be used to define dimension cutouts. Distributors, and retailers are not agents of ARTUSI and are not authorised to bind ARTUSI by any express or implied undertaking or representation.

This manual is also suitable for:

Alfresco abs2