Summary of Contents for LOGO SILVER Scooter LG1
- Page 1 Find this notice at www.logo-silver.fr THE SCOOTER THAT COMBINES ADVANCED TECHNOLOGY WITH STYLE. CONVENIENT AND EASILY MANOEUVRABLE WITH A POWER FOLDING SWITCH.
-
Page 2: Table Of Contents
CONTENTS INTRODUCTION ......................II. SPECIFICATION AND STRUCTURE ................. TILLER CONSOLE ........................SPECIFICATIONS ........................III. ASSEMBLY .......................... OPENING THE PACKING BOX ..................FRONT HEAD ADJUSTMENT ..................... FOLDING WITH THE POWER SWITCHES ..............CHARGING YOUR BATTERIES ..................CHARGING YOUR BATTERIES WITH THE OFF-BOARD CHARGER ..... NEW BATTERY USE ....................... - Page 3 VI. SAFETY ..........................13 SAFETY CHECK PRIOR TO USING YOUR SCOOTER ..........13 WEIGHT LIMITATION ......................13 INCLINE INFORMATION ....................13 OUTDOOR DRIVING SURFACES ..................14 MANUAL MODE ........................14 ELECTROMAGNETIC INTERFERENCES ................. 14 TO AVOID AN INJURY, PLEASE OBSERVE THE FOLLOWING SAFETY TIPS ..15 WEATHER PRECAUTIONS ....................
-
Page 4: Introduction
I. INTRODUCTION Read and follow all instructions, warnings, resulting from individual unsafe operation and notes in this manual before attempting or failure to follow the instructions, to operate your mobility scooter for the cautions and warnings in this manual. first time. If there is any information in The symbols below in this manual are used this manual which you do not understand, to identify warnings, notices and operation... -
Page 5: Specification And Structure
II. SPECIFICATION AND STRUCTURE Your scooter consists mainly of the following parts: scooter body, seat unit, controller, motors, batteries, brake lever, drive wheels and anti-tip wheels (see fig. 1). Backrest Control Lever Handlebar Seat Unit Lithium Battery Fold/Unfold button Mode Lever Anti-tip Wheel Drive Wheel fig. -
Page 6: Tiller Console
II. SPECIFICATION AND STRUCTURE TILLER CONSOLE Battery condition indicator Power switch Speed adjustment Knob Control lever fig. 2 SPECIFICATIONS Table 1: Overall size (LxWxH) 950x460x850mm Folding size(LxWxH) 870x460x400mm Seat height 350mm Seat width 360mm Backrest height 285mm Scooter weight(with batteries) 23.8Kg Max. -
Page 7: Assembly
III. ASSEMBLY OPENING THE PACKING BOX Open the packing box, take off all protective liness, and then take the folded scooter out from the box. Twist off the lock, then push the unfold button to extend the scooter. Press A and C first, then press B for folding, and D for unfolding. (fig. 3) The scooter is successfully unfolded when you hear the “click”. -
Page 8: Charging Your Batteries
III.ASSEMBLY CHARGING YOUR BATTERIES Charging is important for the batteries, and the off-board charger provided by us can simply and quickly charge the batteries of this mobility scooter. Note: If the scooter can’t be unfolded as the battery has been depleted, connect the charger to a standby power port and press the power switch to “II”... -
Page 9: Operation
type Deep-cycle sealed lithium battery size 218x166x59mm voltage capacity 10AH The battery can be charged off the scooter. fig.6 IV. OPERATION TILLER CONSOLE The tiller console houses all of the controls needed to drive your scooter, including the key switch, the speed adjustment knob, throttle control lever, battery condition indicator, etc. With all of the controls on the console you can control the various motions of your scooter. -
Page 10: Throttle Control Lever
IV. OPERATION THROTTLE CONTROL LEVER (SEE FIG. 2) This lever allows you to control the forward and reverse speed of your scooter up to the maximum preset with the speed adjustment knob. Pull the left end of the control lever throttle backwards, the brake is disengaged and the scooter will move backward;... -
Page 11: Off-Board Charger
OFF-BOARD CHARGER Take out the battery of its slot, you can charge it with the off-board charger through a 3-pin charger socket inside the battery box. MODE LEVER There is a mode lever at the lower right of the seat base, shown in fig.1. Whenever you do not want to move your scooter with the motor, you can put it in manual mode. -
Page 12: Care And Maintenance
V. CARE AND MAINTENANCE GENERAL GUIDELINES Avoid knocking or bumping all control parts; • Avoid prolonged exposure of your scooter to extreme conditions, such as over heating, cold or moisture; Keep the tiller console clean; • Check all connectors to ensure they are connected firmly and securely; •... -
Page 13: Safety
VI. SAFETY SAFETY CHECK PRIOR TO USING YOUR SCOOTER: • Check all electrical connections. Make sure they are tight and not corroded. • Check all connections to the battery box. Make sure they are correct and secure. • Check the brakes. •... -
Page 14: Outdoor Driving Surfaces
VI. SAFETY OUTDOOR DRIVING SURFACES Your scooter is designed to provide optimum stability under normal driving conditions such as on flat cement roads or asphalt roads. However, your scooter can be also driven on dirt roads. However you should avoid driving on the following roads: •... -
Page 15: To Avoid An Injury, Please Observe The Following Safety Tips
TO AVOID AN INJURY, PLEASE OBSERVE THE FOLLOWING SAFETY TIPS • Ensure that the power is turned off, see “VI. OPERATION” • Ensure that your scooter is not in manual mode. • Keep your scooter as near to you as possible. •... -
Page 16: Warranty
VII. WARRANTY FIVE-YEAR WARRANTY Our corporation has passed the ISO9001 and ISO13485 certificate. The quality is guaranteed. COVERED BY WARRANTY: Five years warranty on the front and the rear main frames from the date of purchase. One-year warranty on the following parts from the date of purchase: •... - Page 17 P·17...
- Page 18 P·18...
- Page 19 P·19...
- Page 20 Logo Silver www.logo-silver.fr 32 rue de Comboire - 38130 Echirolles - France Tél. +33(0)4 76 21 22 19 - contact@logo-silver.fr...