Table of Contents
Advertisement
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Gate Titan
Summary of Contents for Gate Titan
- Page 1 Q UI CKSTA RT G U IDE Q UI CKSTA RT G U IDE...
- Page 3 3. Safety Summary ..................10 4. Installation ....................13 4.1. TITAN V2 .................... 18 4.2. TITAN V3 ..................... 24 4.3. TITAN V2 NGRS ................... 28 5. Quick Access Menu ..................33 6. Programming via Trigger ................37 7. Programming via USB-Link ................ 45 8.
- Page 4 Introduction Introduction...
- Page 5 Congratulations on your new TITAN, an AEG Control System which will transform your airsoft gun into an advanced training weapon. Designed for enthusiastic airsoft players, the TITAN with its multiple functions encourages you to push your boundaries and play at...
- Page 6 By upgrading the firmware, you directly support GATE R&D works and contribute to the development of innovations in airsoft. Thank you. TITAN is available in 3 firmware editions: BASIC, ADVANCED and EXPERT. The best for those who prefer simplicity but require highest quality. Economic version with limited number of functions.
- Page 7 Configurable via GATE Control Station Configurable Function via trigger BASIC edition ADVANCED edition EXPERT edition Trigger sensitivity û ü ü ü adjustment 343 modes. 216 modes. All variations of: All variations of: Safe - Semi - Auto Safe Safe - Semi - Auto...
- Page 8 Configurable via GATE Control Station Configurable Function via trigger BASIC edition ADVANCED edition EXPERT edition Off / 30 BBs / û Series safety limit Off / 30 BBs Off / 1–250 BBs 60 BBs 0.2 s / 0.5 s / 1 s / û...
- Page 9 Configurable via GATE Control Station Configurable Function via trigger BASIC edition ADVANCED edition EXPERT edition û ü ü ü 2-stage trigger LAST / BB1 / BB2 / LAST / BB1 / BB2 / LAST / BB1 / BB2 / BB counter...
- Page 10 Notice You need USB-Link or Blu-Link to connect TITAN with GATE Control Station for Android and Windows/macOS. To connect TITAN with GCS iOS, you must use Blu-Link. * GCS setting is a setting previously defined in GCS app, which value is not available for selection in this programming mode.
- Page 11 Safety Summary For your safety, we recommend this product to be installed by an experienced airsoft service. Read the safety information below carefully before installing the device. Warning Situations that could cause injury to yourself and others. Caution Situations that could cause damage to your device or other equipment.
- Page 12 Warning Before starting the installation process, make sure that your AEG is empty and there are no BBs inside. Warning Do not store or carry flammable liquids, gases or explosive materials in the same compartment as the device, its parts or accessories. Warning Incorrectly connecting positive and negative battery terminals will cause immediate damage to the device, which is not covered by the...
- Page 13 Warning Too high trigger sensitivity may cause accidental shooting. Warning When an airsoft gun is not in use, its battery must be disconnected and hop-up chamber must be empty. Notice You should use an additional fuse between the battery and the device. Notice Avoid using the device around strong electromagnetic fields or when electrostatic discharges, such as lightening, occur in the atmosphere.
- Page 14 TITAN damage. Notice TITAN installation requires deep technical knowledge of gearbox internals. To avoid TITAN damage, we recommend it to be installed by an experienced airsoft service. Notice Do not attempt to mount the device before watching the installation video and checking the full-length PDF manual: www.gatee.eu/manuals...
- Page 15 Caution Incorrect installation may result in sensors’ damage, which is not covered by the warranty. Caution Connectors should be bent according to the photo below. Bending connectors in the opposite direction may cause them to break. If this happens, spare terminals are included in the installation kit.
- Page 16 Notice TITAN V2 and TITAN V3 do not support Infinite torque-up gears. Installation...
- Page 17 Notice Do not use too much grease. Excessive grease may cover sensors or gaps between teeth, which will cause cycle detection issues.
- Page 18 Notice After connecting the device for the first time: 1) download the most updated version of GATE Control Station 2) update the firmware 3) configure the gear type (if your gears are not stock) Notice TITAN V3 and TITAN V2 NGRS require first-time calibration of sensors, what can be performed with USB-Link or Blu-Link and GCS app.
- Page 19 TITAN V2 Caution A sector gear can damage a gear sensor during installation. Stay careful to avoid this damage.
- Page 20 Caution Placing washers in the wrong order will cause a short circuit and permanent damage to TITAN, which is not covered by the warranty. 1. SCREW 2. METAL WASHER 3. INSULATION WASHER 4. TITAN BOARD 5. GEARBOX Installation...
- Page 21 Caution Improper placement of wiring under the motor gear may cause insulation damage and a short circuit, which is not covered by the warranty. Caution ICS gearboxes require modification to avoid TITAN damage.
- Page 22 Do not pull the trigger when gearbox is open. This may result in trigger sensor damage. Notice In case of some triggers (e.g., speed or CNC triggers), first trigger sensors may be covered even when the trigger is not pulled. Installation: TITAN V2...
- Page 23 Notice Fire selector sensor does not detect the black surface. If your fire selector does not have a metal connector, you must use an appropriate sticker from the kit.
- Page 24 The set contains 3 different types of stickers. At first, use a sticker with the narrower black line. If you are not able to calibrate selector well, you should try other sticker types. Installation: TITAN V2...
- Page 25 TITAN V3 Notice TITAN V3 fits CNC gearboxes with very small backlash. While fitting the TITAN, pull the cables and at the same time, push the board into the right place. Pay attention to the area marked in yellow to fit the board correctly.
- Page 26 Notice Use the trigger sticker to make it visible for trigger sensor. Installation: TITAN V3...
- Page 27 Notice TITAN detects trigger position very precisely. In order to use it, you need to eliminate trigger backlash. The set contains 3 trigger anti-backlash stickers of different thickness. Try each of them and choose the most proper one.
- Page 28 Notice The selector plate requires modification. Place the selector sticker according to the photos below. Its position is very important. Installation: TITAN V3...
- Page 29 Warning Pay attention to correctly solder positive and negative TITAN wires to the connector. Incorrectly connecting positive and negative battery terminals will cause immediate damage to the device, what is not covered...
- Page 30 Caution Placing washers in the wrong order will cause a short circuit and permanent damage to TITAN, what is not covered by the warranty. 6. SCREW 7. METAL WASHER 8. INSULATION WASHER 9. TITAN BOARD GEARBOX Installation: TITAN V2 NGRS...
- Page 31 Caution Caution Do not use cut-off lever Improper placement of screw to secure the TITAN wiring under the motor gear board. may cause insulation damage and a short circuit.
- Page 32 Caution In order to secure the wires properly, modify the gearbox as shown in the photos below. Installation: TITAN V2 NGRS...
- Page 33 Notice The selector plate requires modification. Place the selector sticker according to the photos below. Its position is very important.
- Page 34 Quick Access Menu You can set Pre-cocking mode, Profile of settings or go to programming via trigger mode by using a shortcut. After firing a shot, burst or while in Safe mode* (if safety lever is removed), hold the trigger and switch fire selector in appropriate time (see table).
- Page 35 Programming via Function Pre-cocking mode Profiles of settings trigger To enter the function, and switch fire selector and switch fire selector for > 7 s hold the trigger in < 2 s within 2–7 s Option Low vibrations Option High vibrations See full description Available options page 55...
- Page 36 5. Release the trigger to save selected mode Selecting Profiles of settings Profiles are sets of particular settings of configurable TITAN functions*. There are 3 profiles possible to select at a time and one of them is set as currently active.
- Page 37 2. Keep the trigger held 3. Switch fire selector within 2–7 s. You should hear 1 high vibration. 4. Now each fire selector switch means the next option: a. 1 high vibration – Profile 1 b. 2 high vibrations – Profile 2 c.
- Page 38 Programming via Trigger This programming mode allows you to set options of TITAN basic functions. Notice Particular options in the programming via trigger mode may be different in custom/OEM versions of TITAN. Notice To run programming via trigger and fire selector, your AEG must have a physical 3-stage fire selector.
- Page 39 Turning on the programming mode* 1. Switch fire selector position to SEMI 2. Fire a shot or burst 3. Keep the trigger pulled for 7 seconds – until you hear a vibration Turning on the programming mode – the second ‘backup’ method 1.
- Page 40 You can easily change menu level by switching fire selector. You navigate given menu very quickly by pulling the trigger. Each time you pull the trigger, number of accompanying vibrations changes. The table presents functions and their options programmable via trigger as well as how they are indicated by vibrations.
- Page 41 FUNCTION WITH CORRESPONDING NUMBER OF VIBRATIONS AND LED COLOR Battery Active Gear Fire mode Burst mode Advanced* protection brake ratio OPTION WITH CORRESPONDING NUMBER OF VIBRATIONS AND LED COLOR * To evoke options of Advanced function, hold the trigger down for more than 3 seconds. ** GCS setting is a setting previously defined in GCS app, which value is not available for selection in this programming mode. Once you change such setting to a different option during programming via trigger and then disconnect the battery, it is no longer possible to set that setting from this level (it can be still...
- Page 42 Selecting a function 1. Switch fire selector to SEMI 2. To get to a given function, pull the trigger right number of times (according to the table on page 40) Selecting option of a function 1. Switch fire selector to AUTO 2.
- Page 43 2. Then, the setting is saved, and you are back in the functions menu 3. If you want to, set options for other basic functions in the same way Exiting the programming mode 1. Switch fire selector to SAFE 2. Enjoy TITAN functions you’ve just set...
- Page 44 Activating Safe mode if not assigned If Safe mode is not assigned in the GCS app, it is possible to activate it via selector*: 1. Switch selector fast in sequence: SAFE à SEMI à SAFE (SAFE à AUTO à SAFE for AK-47 selector type) 2.
- Page 45 5x Full is selected for function Burst mode, you will hear 3 vibrations. Notice TITAN remembers your settings, so you always know which option is presently set. Therefore, if you already defined TITAN functions, their programming starts from option currently specified for a given...
- Page 46 Programming via USB-Link Notice You need USB-Link or Blu-Link to connect TITAN with GATE Control Station for Android and Windows/macOS. To connect TITAN with GCS iOS, you must use Blu-Link. Notice You can find how to program your device using Blu-Link in the manual included in the Blu-Link kit.
- Page 47 1. Download and install GATE Control Station: www.gatee.eu/gcs Notice Your Android device must support OTG technology to run GATE Control Station app. 2. Connect the USB-Link via its Micro-USB plug to PC, Mac or smartphone using one of the dedicated USB cables: •...
- Page 48 USB-Link and smartphone to appropriate ends of the cable. Otherwise, it will not work. Notice If your USB-Link cannot be detected, follow the instructions displayed on GATE Control Station screen. Programming via USB-Link...
- Page 49 3. Connect TITAN to the USB-Link Notice If your USB-Link cannot detect TITAN, check if the same happens for another PC, Mac or smartphone. If the problem still occurs: a. email us at titan@gatee.eu b. contact us via Facebook: www.facebook.com/gatee c.
- Page 50 USB-Link Troubleshooting USB-Link has a 4-color LED indicator. BLUE (glowing) The USB-Link is connected to PC, Mac or smartphone. TITAN is not connected or PC/Mac driver is not installed. You can download the driver here: www.gatee.eu/drivers BLUE (blinking) The USB-Link does not have firmware installed.
- Page 51 GREEN (glowing) The USB-Link is connected to TITAN and PC, Mac or smartphone. GREEN (blinking) The USB-Link is connected to TITAN and PC, Mac or smartphone, but TITAN does not have firmware installed. Please install the TITAN firmware. YELLOW (glowing)
- Page 52 RED (glowing) Communication with TITAN was interrupted while saving settings. TITAN settings may have been transmitted incorrectly. Please check the connection between the USB-Link and TITAN. USB-Link Troubleshooting...
- Page 53 Restoring the factory settings results in resetting the default settings, erasing adaptations and statistical data. Notice Restoring the factory settings of TITAN V3 or TITAN NGRS requires its re-calibration in the GCS app. You can restore the factory settings in 3 ways: 1.
- Page 54 2. While in programming mode (only for TITAN V2) a. Turn on the programming mode as described in chapter Programming via Trigger b. Switch fire selector to SEMI c. Pull the trigger 5 times to select function Advanced (6 vibrations) d.
- Page 55 c. While the trigger is pulled, connect the battery (ignore warning vibrations) d. Hold the trigger for 10 seconds until you hear 2 vibrations confirming the reset (ignore vibrations occurring in the meantime, informing about entering the programming mode) e. Release the trigger Notice The trigger must be held down throughout entire operation –...
- Page 56 Each warning is communicated by 3 vibrations: High – Mid – High. Vibrations after connecting the battery TITAN can detect number of battery cells automatically. If you activate this function, vibrations start once the battery is connected. Remember to always check if TITAN detected correct number of battery cells.
- Page 57 4 short high, 1 long low frequency voltage is too high. Lack of trigger or selector 3 short low frequency calibration. Trigger error. After connecting the battery, TITAN detected 4 short low frequency trigger position in which a shot may be fired.
- Page 58 Diagnostic Trouble Codes Diagnostic Trouble Codes (DTC) enable detecting basic malfunctions and problems with your AEG or TITAN. You are notified of the main errors with motor vibrations. DTC can be later read and cleared in DTC menu in GCS app as well as in the programming mode from the level of Advanced function settings.
- Page 59 Notice It is a good practice to clear the DTC in GCS before each skirmish. How to read DTC explanations Number of vibrations High frequency vibration Low frequency vibration...
- Page 60 Battery protection was activated. What happened: The battery is discharged What to do: Charge the battery Under Voltage Protection 2 (UVP2) The voltage dropped below 1.9 V which is critical for TITAN to work properly. What happened: 1. The battery is discharged TITAN Troubleshooting...
- Page 61 2. The battery is worn out and has too high internal resistance 3. Inadequate battery type for given AEG configuration 4. Too much electrical resistance between TITAN and the battery 5. Motor too strong for the connected battery 6. Motor connections’ short circuit 7.
- Page 62 What to do: 1. Set the same number of cells in GCS as in the battery 2. Charge the battery Motor Disc (MOTOR DISC) TITAN did not detect the motor. What happened: 1. Motor is not connected 2. Brushes are worn out 3.
- Page 63 2. Connect the motor 3. Replace brushes 4. Replace the motor Gear Not Detected (GND) TITAN did not detect the sector gear. What happened: 1. Too high sector gear shimming 2. Sector gear sensor is dirty 3. Sector gear sensor is damaged 4.
- Page 64 Cycle detection to Off Overload (OVL) Too high load. The load limit was exceeded. What happened: TITAN with BASIC and ADVANCED firmware edition is dedicated for up to mid-tuned guns What to do: 1. Use high-torque motor and gears 2.
- Page 65 Over Current Protection (OCP) TITAN detected too high current. Over current protection was activated. What happened: 1. Motor is damaged 2. Motor or gearbox is jammed 3. Motor connections’ short circuit What to do: 1. Replace the motor 2. Unjam the motor or gearbox...
- Page 66 Short Circuit Protection (SCP) TITAN detected current over 220 A. Short circuit protection was activated. What happened: 1. Motor is damaged 2. Motor or gearbox is jammed 3. Motor connections short circuit What to do: 1. Replace the motor 2. Unjam the motor or gearbox 3.
- Page 67 1. Outside temperature is too high in correlation with the demanding AEG 2. Frequent short circuits and TITAN electrical overloads What to do: Wait until the temperature drops Self-test Failure (STF) The device failed on self-test. What happened: Internal error of the device What to do: Contact titan@gatee.eu...
- Page 68 EXCLUSION OF LIABILITY GATE Enterprise sp. z o.o. sp. k. is not liable for any damages, injuries or accidents of any kind resulting from the use of this product or airsoft gun with the product installed, including (but not limited to) incidental or intentional damages to airsoft gun, airsoft gun parts, batteries and gearbox internals.
- Page 69 GATE LIMITED WARRANTY POLICY GATE Enterprise sp. z o.o. sp. k. warrants that its product is free from manufacturing and material defects at the date of purchase and for a nonextendable period of two (2) years from the date of purchase. This Limited Warranty is conditioned upon proper use of the product by Purchaser.
- Page 70 CERTIFICATE OF CONFORMITY GATE Enterprise sp. z o.o. sp. k. hereby declares under our sole responsibility that the products GATE TITAN V2, TITAN V3 and TITAN V2 NGRS are in conformity with essential requirements of the following Directives: EC DIRECTIVE 2011/65/EU.
- Page 71 GATE Enterprise Sp. z o.o. Sp. k. Torowa 3H /Gatee PL-30435 KRAKÓW /GateEnterprise Email: office@gatee.eu /GateMovies Tel: (+48) 122-100-523 /GateEnterprise www.gatee.eu...
- Page 72 Read the full manual: Read the full manual: gatee.eu/manuals gatee.eu/manuals...