1. Manuals
  2. Brands
  3. DAHAO Manuals
  4. Control Unit
  5. BECS-328
  6. Manual

DAHAO BECS-328 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

B E C S –328
Version：2008-03

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BECS-328 and is the answer not in the manual?

Questions and answers

Anna Marie Ellitson
January 28, 2025

The needles no.7;8; 9 don't want to work. The buttons don't register if press.

0
2 comments:
Mr. Anderson
February 10, 2025

If needles no. 7, 8, and 9 on the DAHAO BECS-328 are not working and the buttons do not register when pressed, you can try initializing the system parameters to resolve the issue. Follow these steps:

1. Press and hold the designated key (not specified in the provided content).
2. Turn on the power of the machine while holding the key.
3. The system will initialize the parameters.

This process helps reset any system errors caused by outside interference or software issues. If the problem persists, further troubleshooting may be required.

This answer is automatically generated

0
Francis URBAIN
March 18, 2025

@Anna Marie Ellitson

0
Francis URBAIN
March 18, 2025

J' ai une gros problème pour la position d'arrêt initiale 100° toujours décalé au 107°, coupe fil ne fonctionne pas mais c'est activé au paramètre

0

Summary of Contents for DAHAO BECS-328

  • Page 1 B E C S –328 Version：2008-03...
  • Page 2 CERTIFICATE OF CONFORMITY OF QUALITY MANAGEMENT SYSTEM CERTIFICATION This is to certify that the quality system of Beijing Xingdahao Technology Co., Ltd. Is in conformity with GB/T 19001-2000 idt ISO 9001:2000 Standard This certificate is valid to the following product(s)/service: Design and manufacture of computerize sewing Equipment control system Registration No.:0203Q15748R2M...

  • Page 3: Table Of Contents

    TART UTOMATIC TART ....................24 DURING MBROIDERY )..... 25 ETTING UTOMATIC OLOR CHANGING EQUENCE OLOR ..... 26 TORING THE ANUAL OLOR CHANGING UMBER INTO OLOR ..................27 OLOR CHANGING PEED CHAPTER 6 SETTING DESIGN DIRECTION..................29 BECS-328 Computerized Embroidery Machine's Manual...
  • Page 4 ..43 IEWING THE OMMON ARAMETERS AND ETTING THE HOWING ARAMETERS 11-2 ................44 ISPLAY MBROIDERY TATISTICS 11-3 X/Y D ......46 LEARING CCUMULATED TITCH OUNT AND ISPLACEMENT 11-4 ................46 WITCHING OF ISPLAY ANGUAGE BECS-328 Computerized Embroidery Machine's Manual...
  • Page 5 EMORY 14-2 ....................68 OW TO DIT A TITCH 14-3 .................. 70 APIDLY EARCHING A TITCH 14-4 ..............70 APIDLY EARCHING A PECIAL TITCH 14-5 ..................... 71 LOCK PERATION 14-6 ...................... 71 ELP FOR DITING BECS-328 Computerized Embroidery Machine's Manual...
  • Page 6 ASSWORD FOR 25-3 "NO OUTPUTTING DESIGN"......92 ANCELING THE ASSWORD FOR CHAPTER 26 TESTING ..........................93 26-1 ....................93 OMPUTER ESTING 26-2 ..................... 93 NCODER ESTING 26-3 ..................93 HAFT PEED ESTING 26-4 ....................93 ECHANICAL ESTING BECS-328 Computerized Embroidery Machine's Manual...
  • Page 7 ARAMETER ETTING FOR EQUIN MBROIDERY 31-2 ............106 ANUAL PERATION OF EQUIN MBROIDERY CHAPTER 32 TABLE OF THE MACHINE PARAMETERS............107 APPENDIX: ALL FUNCTIONS IN DIFFERENT MODES............113 ALL RIGHTS RESERVED. BEIJING XING DAHAO TECHNOLOGY CO., LTD. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 8: Chapter1 General Descriptions

    Please abide all the warnings and safety requirements to save life. Overloading may cause serious loss. Please load according to the Force instruction on the box.. Installation Don't jam the vent on the device. Don’t plug up the machine, or it may set Notice fire. BECS-328 Computerized Embroidery Machine's Manual...
  • Page 9 If you need to open the machine cover, cut out the power supply first. Duo Warning to the capacitance after power off, operator must wait one minute till he can open the machine cover. Circuit boards can be damaged by static. Non-professional technician can Notice BECS-328 Computerized Embroidery Machine's Manual...

  • Page 10: Main Features

    The designs in computer memory can be output to floppy/USB disk. The designs are output in Tajima DSB format, which can be used in internet transmission. 3) The software of BECS-328 can be removed by floppy/USB disk. BECS-328 Computerized Embroidery Machine's Manual...
  • Page 11 PAR. It can be embroidered at one time. 10. Compiling Design A. Compiling the ready-for-embroider design BECS-328 Computerized Embroidery Machine's Manual...
  • Page 12 This function is to combine the pattern with selected embroidery parameters such as color sequence, pattern direction, rotation angle and repetition, etc. to reduce the times of inputting parameters when embroider the pattern without changing the parameters. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 13: Chapter 2 Names Of Parts About Electrical Control System

    Design direction Press the key to make design direction change Manual trimming After machine stops, click it to do manual trimming. Return to origin With this function, the frame can return back to the BECS-328 Computerized Embroidery Machine's Manual...
  • Page 14 . help Press the key to display help. 20，21 Speed-adjust Press to reduce speed and rise. Assistant Press the key to enter assistant management. Disk(USB) Press it to enter the disk(USB) management, which BECS-328 Computerized Embroidery Machine's Manual...

  • Page 15: Operation Bar And Turn Shaft Button

    When the switch is pushed to middle position from down position, the lamp will be green and the head is in normal embroidering mode. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 16: Chapter 3 How To Start Embroidery

    The working statuses of computer embroidery machine can be divided into 3 statuses: 1. Preparation status: features: machine stops and the icon " " blinks. 2. Embroidery confirmation status: features: machine stops, and the icon " " appears. BECS-328 Computerized Embroidery Machine's Manual...
  • Page 17 : The machine is in embroidery confirmation status. : The machine is in preparation status. : The machine is in auto-color and auto-start mode. : The machine is in auto-color and manual-start mode. BECS-328 Computerized Embroidery Machine's Manual...
  • Page 18 If the number is replaced by "⊗", the menu item can not be entered. (The parameter cannot be set or is not functional in the current setting.) If a menu item has a BECS-328 Computerized Embroidery Machine's Manual...

  • Page 19: Input A Design Into Memory From Floppy Disk

    ⑧DELETE LETTER LIBS ⑨DESIGN A LETTER PATTERN ⑩INPUT DESIGN FROM PC ARROW: MOVE, ENTER: CONFIRM 2.Press " “, “ " or numeric key "2" to move the cursor to "INPUT", and then press " " key. BECS-328 Computerized Embroidery Machine's Manual...
  • Page 20 8.Then the pattern file begins to be transmitted from disk to machine memory, and the operation finishes. Operation 2: (by the operation of "Design Management") 1.Press " " key (in embroidery preparation status), the computer shows as follows: BECS-328 Computerized Embroidery Machine's Manual...

  • Page 21: Preparation Before Embroidering

    (2) automatic start or manual start, which is to start automatically or manually after automatic color-changing, and if it is automatic color-changing, the color line should be set. (3) besides, it is necessary to set BECS-328 Computerized Embroidery Machine's Manual...

  • Page 22: Select A Pattern For Embroidery And Confirm To Embroider The Pattern

    2. Explanations about saving and storing embroidery parameters. BECS-328 Computerized Embroidery Machine's Manual...
  • Page 23 (5) If the computer has saved the set parameters of this design and the current parameters are different from them, the prompt is "RESTORE PARAMETERS?", and you can select "YES" or "NO" with pressing " "、" " key and pressing " " key to decide whether the BECS-328 Computerized Embroidery Machine's Manual...
  • Page 24 (5) In the main picture, the icon " " appears and the machine enters into the embroidery confirmation status. Now, you can pull the bar to start embroidery. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 25: Normal Embroidering, Returning And Darning Embroidering

    "Disk Management" and "Design Management". Operation: (1) Press " " key, the computer shows as following: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 26 Chapter 3 How to Start Embroidey (2) Press " " key to release embroidery confirmation status according to the prompt (or press other keys to abandon), and then enter into the embroidery preparation status (the icon " " blinks.). BECS-328 Computerized Embroidery Machine's Manual...

  • Page 27: Chapter 4 Normal Embroidery And Idling

    When pulling bar for returning, the main shaft keeps inactive, but the frame returns along the stitch trace. 4-3 High-speed Idling Operation: Press " " key when machine stops until the following display appears: BECS-328 Computerized Embroidery Machine's Manual...

  • Page 28: Release Of Low-Speed/High-Speed Idling

    4-4 Release of Low-speed/High-speed Idling Operation: Press " " key when machine stops until the following display appears: The icon " " appears. This is the state of normal embroidery. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 29: Positioning Idling

    ⑥LAST STOP ARROW：MOVE， ENTER：CONFIRM (3) Press " "、" " key to select the desired positioning idling, and then press " " key. (4) Continue the operation for different positioning idling according to the prompts respectively. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 30: Chapter 5 Color-Changing Operation

    " appears for manual color-changing. At the moment, the operator should press the digital key to carry out manual color-changing. After the required needle position having been set, pull the operation bar to start embroidery (manual start). BECS-328 Computerized Embroidery Machine's Manual...

  • Page 31: Automatic Color - Changing And Manual Start ( Or Automatic Start )

    If the machine is set into automatic color-changing, the color-changing sequence (or be called color line) should be set in advance before the embroidery confirmation status. When pulling the operation bar to start embroidery, the computer will carry out BECS-328 Computerized Embroidery Machine's Manual...

  • Page 32: Setting Automatic Color-Changing Sequence (Or Color Line)

    (4) If press “3” and " " key, then you can modify the color line in whole by switching the needle number. For example: if the color line is :1,2,3,1,2,3,1,2,3… Select: OLD NDL: 3 NEW NDL: 5 BECS-328 Computerized Embroidery Machine's Manual...

  • Page 33: Storing The Manual Color-Changing Number Into Color Line

    "、 " " or digital key "7" to move the cursor to "SET MACHINE PARAS", and then press " " key. (3) Press " " key to turn to page 2, which is as following: BECS-328 Computerized Embroidery Machine's Manual...

  • Page 34: The Color-Changing Speed

    ARROW：MOVE， ENTER：CONFIRM Press " "、" " or digital key "7" to move the cursor to "SET MACHINE PARAS", and then press " " key. Press " " key to turn to page5, which is as following: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 35 " or digital key "2" to move the cursor to "COLOR-CHANGE SPEED", and press " " key. (5) Press " "、" " key to select the data, and greater data represents higher speed. (6) Press " " key. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 36: Chapter 6 Setting Design Direction

    Take the embroidering of letter “F” as an example to explain the relations between the embroidered pattern and the design direction: Operation: Press " " key to change the design direction until the desired direction is selected. The icon will be changed. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 37: Chapter 7 Frame Operations

    Operation: A. Press " " key, the menu frame appears as follows: ①BACK TO ORIGIN ②RESTORE ORIGIN ③SAVE ORIGIN ④AUTO SET ORIGIN ⑤FRAME TO BORDER ⑥NDL DOWN&ORIGIN BECS-328 Computerized Embroidery Machine's Manual...

  • Page 38: Save Pattern's Origin Point

    This function would calculate the origin point for the selected pattern, and move the frame to the new origin point, which will make the pattern at the center of frame. Operation: A. Press " " key, the menu frame appears as follows: BECS-328 Computerized Embroidery Machine's Manual...

  • Page 39: Moving Frame Along The Border

    7-7 Returning to the Origin Point with needle down This function is designed for returning to the origin point after releasing the cloth from the frame (in roll-cloth embroidery). Prior to this operation the parameter “AUTO ORIGIN” in BECS-328 Computerized Embroidery Machine's Manual...

  • Page 40: Returning To The Stop-Embroidery Point

    After the completion of patching cloth, this function can make the frame return to the stop-embroidery point. Operation: (1) Press the manual frame-shifting key to shift the frame out (for patching cloth). (2) Press " " key, the main picture appears as follows: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 41 Chapter 7 Frame Operations (3) Press " " key to confirm the operation, or press any other key to quit. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 42: Chapter 8 Embroidery Speed (Main Shaft Speed)

    " or digital key "7" to move the cursor to "SET MACHINE PARAS", and then press " " key. (3) Press “ ”to turn to the third page and select the option "MAX. SPEED", and press " " key. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 43: Setting Embroidering Speed

    (2) Press " " key. When pressing once the key, the speed will reduce 10 rpm. When reducing to 250 rpm, the speed will not reduce any more. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 44: Chapter 9 Trimming Thread

    " key, the main screen appears as follows: ①TRIM BOTTOM AND UPPER THREAD ②TRIM BOTTOM THREAD (2) Press " "or" " key to select the trimming method and press " " key to trim thread or press “ ” key to quit. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 45: Chapter 10 Disk Operations

    " key to vary the display speed. Press " " to end the display. (5) Press " " or " " key to quit the disk operation. 10-2 Input Pattern from Disk to Memory Operation: BECS-328 Computerized Embroidery Machine's Manual...

  • Page 46: Output Pattern From Memory To Disk

    “Input Pattern from Memory to Disk”, this function is able to complete the operation of copying a pattern from a disk to another disk. Operation: (1) Insert the pattern disk into floppy/USB disk driver, and press " " key, the disk BECS-328 Computerized Embroidery Machine's Manual...

  • Page 47: Deleting The Pattern In Floppy Disk

    ⑥FORMAT 1.44M ⑦INSTALL LETTER LIBS ⑧DELETE LETTER LIBS ⑨DESIGN A LETTER PATTERN ⑩INPUT DESIGN FROM PC ARROW：MOVE， ENTER：CONFIRM (2) Press " "、" " key or digital key "4" to move the cursor at "DEL FILE", BECS-328 Computerized Embroidery Machine's Manual...

  • Page 48: Formatting A 720Kb Diskette

    It carries out formatting of a high density 3.5 inch diskette in DOS format. Operation: (1) Insert the pattern disk into floppy/USB disk driver, and press " " key, the disk operation menu appears as following: BECS-328 Computerized Embroidery Machine's Manual...

  • Page 49: Installing The Letter Library

    10-8 Deleting letter library Please read the related part in chapter 16. 10-9 Designing Letter Pattern Please read the related part in chapter 16. 10-10 Input Design from PC Please read the related part in chapter 29. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 50: Chapter 11 Displaying Parameters And Frame (Picture)

    Chapter 11 Displaying Parameters and Frame (Picture) 11-1 Viewing the Common Parameters and Setting the Showing Parameters Operation（embroidery preparation）: (1) Press " " key to change the main picture as one of the four following pictures: BECS-328 Computerized Embroidery Machine's Manual...

  • Page 51: Display Embroidery Statistics

    11-2 Display Embroidery Statistics Operation: (1) Press“ ”to display the first page of embroidery information. [EMBROIDERY] TOTAL TIME： 4:38:45 EMB. TIME: 4:32:19 STOP TIME: 0:6:26 T.B. NUM: T.T. TIME: 0:20 TOTAL WORKS: POWER NUM: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 52 Total Time is the total time of embroidering time and stop time. Emb. Time is the total time of “normal embroidering”, “low speed idling” and “high speed idling”. Stop Time is the time when the machine does not run. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 53: Clearing Accumulated Stitch Count And X/Y Displacement

    " key until the "Overall Stitch Count" or "X/Y Displacement" is on the main picture. 11-4 Switching of Display Language 1. Changing the Chinese display into English display (in Chinese display) Operation: (1) Press " " key, the menu appears as following: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 54 When the system language is in certain state, press this key to shift to the next language main screen (Note: when the system in the last language, press this key to shift to the first one). BECS-328 Computerized Embroidery Machine's Manual...

  • Page 55: Chapter 12 Assistant Operation And Setting The Parameters

    89° (1) Angle of rotation ( Use digital key, " " and " " keys to input data. This angle is an angle at which a pattern rotating counterclockwise according to the selected design direction. BECS-328 Computerized Embroidery Machine's Manual...
  • Page 56 (8) X repetition distance (unit: mm) Use digital key, " ", " " , “ ”and " " keys to input data. X repetition distance presents the distance between the starting points of two adjacent patterns in transverse direction BECS-328 Computerized Embroidery Machine's Manual...

  • Page 57: Frame To Point

    ⑩TO SET CYCLIC EMB. ARROW：MOVE， ENTER：CONFIRM 2. Press " ", " " key or digital "3" to move the cursor to "DESIGN RANGE'S OPERATIONS", and press " " key to enter the next menu as following: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 58 “ESC” key; finally, you can pull the bar directly to start embroidering, the machine will embroider along the trace in converse direction to current position, and return to the “preparation status” automatically. (5) Embroider one cross at current position BECS-328 Computerized Embroidery Machine's Manual...

  • Page 59: Setting The Offset Point (Under Embroidery Confirmation Status)

    " key to go to the main picture. 12-4 Setting the Offset Point (under Embroidery Confirmation Status) What is called offset point can be an arbitrary point beyond the starting point of the pattern as shown in the following figure: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 60 (6) Press " " key to continue. (7) Pull the bar and start embroidering. Note: The offset point also is the point to which the frame automatically moves while BECS-328 Computerized Embroidery Machine's Manual...

  • Page 61: Setting Frame Protection When Power Off (Setting The Machine's Zero Point)(In Embroidery Preparation State)

    If the frame has been moved after power off, or if power on again after maintenance, you should do again the operation of “Setting frame zero point manually”. Operation: (1) Press " " key, the menu appears as follows: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 62 ⑤SET POWER RESUME/ZERO POINT ⑥POWER RESUME ⑦SET MACHINE PARAS ⊗COMPENSATION ⑨ 中文/ENGLISH/SPANISH ⑩TO SET CYCLIC EMB. ARROW：MOVE， ENTER：CONFIRM (2) Press " ", " " keys or numeric key "5" to move the cursor to " SET POWER BECS-328 Computerized Embroidery Machine's Manual...

  • Page 63: Frame Restoring After Power Off

    (3) Press " ", " " key or numeric key "6" to move the cursor to "POWER RESUME", and press " " key. (4) Continue the operation according to the prompt, and the restoration of frame position BECS-328 Computerized Embroidery Machine's Manual...

  • Page 64: Demanding Whether Setup Frame Zero Point Or Not

    (3) The machine parameters are in 5 pages (you can press " " or " " key to turn to other pages), which are as chapter 32. The parameters can be revised using " ", " ", digital keys, " " and " " keys. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 65: Compensating Of Satin Stitches

    " to go to the main picture. (8) During the input design process, the compensated design can be input to the memory directly by the prompt. 12-10 Chinese/English/Spanish Please read the related part in chapter 11. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 66: Set Cyclic Embroidery

    “Set Date＆Time”. At last press “ ”: 2008:04:07 15:21:40 2008 ARROW:MOVE, ENTER:CONFIRM (3) Press “ ”or“ ”not to change the clock of the system. ”or“ ”,then press“ ” to change the clock of the system and save it. Press “ BECS-328 Computerized Embroidery Machine's Manual...

  • Page 67: Chapter 13 Management Of Pattern In Memory

    (3) Directory of pattern in memory is listed on screen and the pattern at the cursor is displayed automatically. In case of the directory exceeding one page, use " " or " " key for viewing. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 68: Input A Design Into Memory From Floppy Disk

    ②SHOW MEMORY DESIGN ③DISK INPUT ④COPY ⑤EDIT ⑥DELETE ⑦DIVIDE ⑧COMBINE ⑨PACKED DESIGN ⑩CLEAR ALL ARROW:MOVE, ENTER:CONFIRM (2) Press " "、" " or digital key"4" to move the cursor to "COPY ", and then press " " key. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 69: Edit The Pattern

    (4) After the computer deletes the pattern, it will go to the design management menu. (5) Press " " or " " to end the design management. 13-7 Divide the Pattern This operation is intended for dividing the pattern in memory into two new patterns and BECS-328 Computerized Embroidery Machine's Manual...

  • Page 70: Splice Two Patterns

    (7) The computer does the dividing, and then will go to the design management menu. (8) Press " " or " " to end the design management. 13-8 Splice two Patterns Operation: (1) Press " " key, the computer shows the design management menu as following: BECS-328 Computerized Embroidery Machine's Manual...

  • Page 71: Editing The Packed Pattern

    The packed pattern means a pattern group packed from several (less than 100) normal patterns in memory after setting parameters, which is intended for continuous embroidery automatically. Operation: (1) Press " " key, the computer shows the design management menu as follows: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 72 " key to store the packed pattern and return to the design management. Or press " " key and decide whether you save the packed pattern, then return to the design management. (5) Press " " or " " to end the design management. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 73: Clear All Patterns In Memory

    " key to clear all patterns. If select [NO] and press " " key or press " " key to give up the operation. (4) Press " " or " " to end the design management. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 74: Chapter 14 Edit Of The Pattern In Memory

    If you select [NO] and press " " key, then you can select an existent normal pattern for editing. (4) After editing the pattern (See the following sections), the design management appears. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 75: How To Edit A Stitch

    Its codes are as following. The second row is the value of X (unit: 0.1 mm) and the third row is the value of Y (unit: 0.1 mm). 0 : invalid stitch 3 : satin stitch 4 : jumping 5 : frame jumping 6 : absolute jumping 7 : color-changing BECS-328 Computerized Embroidery Machine's Manual...
  • Page 76 “+”, then press " ", "6" and "3" keys. 2. Deleting a stitch ", “ ” 、 “ ” keys to move the cursor underneath the stitch to be Use " ", " BECS-328 Computerized Embroidery Machine's Manual...

  • Page 77: Rapidly Searching A Stitch

    (2) Press " "、" " or digital key"2" to move the cursor to "GO TO CODE", and then press " " key. (3) Input the code of stitch which the computer will search backwards from the current BECS-328 Computerized Embroidery Machine's Manual...

  • Page 78: Block Operation

    “READ” means that the machine will take a pattern (you first input the number of pattern) as a block and read the block at end of editing pattern. 14-6 Help for Editing Operation: (1) Press " " key to enter into the following menu: BECS-328 Computerized Embroidery Machine's Manual...

  • Page 79: Saving The Editing Pattern And Exit

    " or digital key "6" to move the cursor to "QUIT", and then press " " key. (3) The computer prompts you to save the editing pattern, and you can select [YES] or [NO], then press " " key to go to the design management operation. BECS-328 Computerized Embroidery Machine's Manual...
  • Page 80 Chapter 14 Edit of the Pattern in Memory (4) The computer exits the editing. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 81: Chapter 15 Operations Help

    This function helps users to perform the operations and displays prompting message. Operation: (1) At the main picture, press " " key to enter the help-show frames (2) Press any key to turn to other frames until exit. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 82: Chapter 16 Monogramming And Making A High-Speed Pattern

    If so it were, the file count should increase by 56. Otherwise do the operation of “Deleting letter library” first and then do this operation again. 2. Deleting letter library Operation: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 83 DESIGN A LETTER PATTERN” if PATTERN", and then press " " key.(Note: It can not enter into “ not install letter libs (3) Then enter into the setting parameters of the characters as follows figure. After BECS-328 Computerized Embroidery Machine's Manual...

  • Page 84: Making A High-Speed Pattern

    And if you hope it does not occur, you can make a high-speed pattern from the pattern and embroider with the high-speed pattern, which will not make the main shaft slow down. Operation: (1) Press " " key, and then press" " key, the menu appears as following: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 85 (4) Input the number of the new high-speed pattern. (5) The system will create the new high-speed pattern automatically. (6) Press the key " " to go to the main picture. (7) If necessary, embroider the new pattern. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 86: Chapter 17 Compile The Packed Pattern And Embroidering Pattern

    (6) Press " " key to go to the main picture. 17-2 Compile the Embroidering Pattern Operation: (1) Press " " key, and then press " " key, the menu appears as following: BECS-328 Computerized Embroidery Machine's Manual...
  • Page 87 (4) Input the number of new pattern, and the system will create the new normal pattern automatically, which is identical with the embroidering pattern having the embroidering parameters. (5) Press " " key to go to the main picture. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 88: Chapter 18 Initialize The System Parameters During Electrifying

    (1) Press and hold " " key, and turn on the power of machine. (2) The system initializes the system parameters and gives a sound, and release off " " key, the machine will start working. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 90: Chapter 19 Adding Patch Codes To A Design

    (4) According to the prompt, you will be asked to add a patch code for each of color codes and stop codes, or not do so. (5) Press " " key to go to the main picture. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 91: Chapter 20 Turn The Main Axis At 100 Degree Manually

    (2) Select the option “LET NEEDLE DOWN” and press “ ”. (3) The screen shows “PRESS ENTER TO CONTINUE ”. Press “ ” and the needle will stick into the embroidery material. (Be careful with this operation.) Or press any other key to exit. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 92: Switching The Valves In Quilt Embroidery

    " or “3” select “V1-4 ON/OFF” and then press “ ”. (2) Press " ”to switch the valve on/off. (3) Select among valve 1~4 and press“ (4) Repeat the above 2 steps to set the other valves. ”to exit. (5) After setting, press“ BECS-328 Computerized Embroidery Machine's Manual...

  • Page 93: Chapter 21 Shift The Frame To Make A New Design

    " key to end inputting the trace points. (7) According to the prompt, input the number of new pattern, and press " " key to create the new pattern. (8) Press " " key to go to the main picture. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 94: Chapter 22 Setting The Cyclic Embroidering

    " " will appear. Otherwise, the machine will be changed into non-cyclic embroidering and the icon " " will replace the former icon " ". (4) The computer will turn to the main picture. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 95: Chapter 23 Adjust The Machine's Braking (For New Machines)

    Adjust the Machine's Braking (for New Machines) 23-1 Summary This function is designed for adjusting the braking control parameters, so as to let Dahao computer suit different embroidery machines. Moreover the mechanic parts may change a little with time, this function can let the Dahao computer and mechanic parts work together better.
  • Page 96 ⑤SET POWER RESUME/ZERO POINT ⑥POWER RESUME ⑦SET MACHINE PARAS ⊗COMPENSATION 中文/ENGLISH/SPANISH ⑨ ⑩TO SET CYCLIC EMB. ARROW：MOVE， ENTER：CONFIRM (2) Press " " or numeric key "7" to move the cursor to "SET MACHINE PARAS", and BECS-328 Computerized Embroidery Machine's Manual...

  • Page 97: Test For Adjusting The Machine S Braking

    23-3 Test for Adjusting the Machine's Braking After adjusting the machine's braking parameters, you can turn the main shaft manually (refer to chapter 20) to check the result. If the result is not satisfactory, adjust the braking parameters again. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 98: Chapter 24 Let The Needle Sew Down And Move The Frame

    (4) Now, you can move the frame to the desired position. Press " " key to finish. (5) After ending the operation, you should turn the main shaft at 100 degree (Seeing chapter 20). (6) At the moment, you can continue embroidering. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 99: Chapter 25 No Output Of The Pattern In Memory

    Having set a password, you can do the steps in section 25-2 and input the password to cancel it. In addition, the computer will cancel the password automatically by executing of the operation of "CLEAR ALL" in design management menu. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 100: Chapter 26 Testing

    26-5 Turn the Main Shaft to Any Angle This operation is to turn the main shaft from 100 degree to any angle to maintain and test machine conveniently. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 101: Chapter 27 Setting The Embroidery Frame Range

    " key to continue. (4) The machine will prompt: “MOVE FRAME TO UP-RIGHT, AND ENTER”. You can press “ ”、“ ”、“ ”、“ ”keys to move the frame to up-right corner. And press " " key to end. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 102: Chapter 28 Generating The Outline Design

    ⑧TO SET ALL HEADS PATCH ⑨TO LET NEEDLE DOWN AND MOVE FRAME ⑩NO OUTPUTTING DESIGN ARROW：MOVE， ENTER：CONFIRM 3、 Press “ ” or “7” key, to move the cursor to “ ” and TO MAKE TRUE DESIGN RANGE BECS-328 Computerized Embroidery Machine's Manual...
  • Page 103 Chapter 28 Generating The Outline Design press “ ” key. ”. 4、 Select one normal design and press“ 5、 Input the design No. of outline design. 6、 The outline design is generated automatically. 7、 Press “ ” key to exit. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 104: Chapter 29 Select Showing Colors

    4. Press the direction keys to select the color and then press “ ” to confirm it. Repeat the above procedure to set color for each needle. ”to exit. 5. After setting, press“ BECS-328 Computerized Embroidery Machine's Manual...

  • Page 105: Chapter 30 Manual Of Embcom Software

    Installation procedure: (1) Run the file SETUP.EXE in the Embcom Setup Disk. Click “Next” to continue or click “Cancel” to exit. Click “Next>” to select the default destination folder. (3) Click “Next>” to go on. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 106: Uninstall

    Chapter 30 Manual of Embcom Software (4) Click “Finish” to complete the installation. 30-2 Uninstall (1) Run “Start->Setup->Control Panel->Add/Remove Programs”. BECS-328 Computerized Embroidery Machine's Manual...
  • Page 107 Chapter 30 Manual of Embcom Software (2) Select “EMBCOM” and click the button “Add/Remove”. (3) Select “Automatic” and then “Next>”. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 108: Run And Use The Embcom Software

    (4) Click “Finish” to delete the software “Embcom”. 30-3 Run and Use the Embcom software Run the software “EMBCOM” by double-clicking its icon. (1) Note: When this software is run for the first time, the machine type has to BECS-328 Computerized Embroidery Machine's Manual...
  • Page 109 (3) Click the button “Send Design to Machine” and the system will ask: “Machine is ready for receiving?” (5) (At this moment, the embroidery machine should be ready to receive design. For details, read the next paragraph). Click “ ” button to start sending design. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 110: Communication Operation Of Embroidery Machine

    ⑩INPUT DESIGN FROM PC CONNECTING… (2) The system will ask to input a new design number. Input a new one and press “ ” key to confirm. The machine shows “Connecting…”. Wait for the computer communication. BECS-328 Computerized Embroidery Machine's Manual...
  • Page 111 (4) After receiving the design, the system will return to the “DISK(USB) MANAGEMENT” menu. For communication failure, the machine will show “Communication Fail” which may be caused by: Communication board (Board E806) error, connecting problem between PC and the machine, or receiving/sending software error. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 112: Chapter 31 Sequin Embroidery Operation

    ⑦TIME OF SEQUIN ACTION: ⑧SEQUIN OFF AFTER T.B.: ARROW：MOVE， ENTER：CONFIRM ”or“ ”to exit the menu “SET MACHINE PARAS”. 4. Press“ ”or“ ”to exit the menu “OTHER MANAGEMENT”. 5. Press“ Note: refer to chapter 32 for the parameter chart. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 113: Manual Operation Of Sequin Embroidery

    ”, and the sequin device will end operation. (4) Press the key “ ” or the digital key “6” to select “SEND SEQUIN” and press “ ”, and the sequin device will begin to deliver a sequin. Press“ ”to exit. BECS-328 Computerized Embroidery Machine's Manual...

  • Page 114: Chapter 32 Table Of The Machine Parameters

    The frame automatically returns to the origin point after embroidery. Parameters must be initialized for a new machine. INITIALIZE SYSTEM! T.B. DETECT WHEN JUMP Thread break detect in case jumping stitches. It should be set according to the real needs. BECS-328 Computerized Embroidery Machine's Manual...
  • Page 115 Choice: 1～10 Speed decreases when the stitch length is larger than this. TURN OFF TRIMMING Yes: shut down trimming function No: turn on trimming function TRIM MODE Choice: 1～8 “1” is the shortest ACTION AFTER TRIM Frame to X/Y, move needle BECS-328 Computerized Embroidery Machine's Manual...
  • Page 116 Choice: 0～30 It’s only for electromagnetic motor. Increase this parameter value to avoid main shaft vibration during braking. Usually it’s set as 1. SET RUN SPEED Choice: 80、 90、 100、 110、 120、 130、 140、 150rpm BECS-328 Computerized Embroidery Machine's Manual...
  • Page 117 “No” for no boring embroidery No thread break detect, trimming, or lock stitch for the boring needle BORING EMB. DISP.(mm) 0/12 Location of boring knife: 0mm or 12mm CORD EMB. NEEDLE The cord embroidery needle number BECS-328 Computerized Embroidery Machine's Manual...
  • Page 118 N） SPEED FOR SEQUIN R 350rpm Choice: 300-600rpm the highest speed of sequin embroidery SPEED FOR SEQUIN L 350rpm Choice: 300-600rpm the highest speed of sequin embroidery SEQUIN R ADJ. ANGLE Sequin delivery angle adjustment：-15~+15。 BECS-328 Computerized Embroidery Machine's Manual...
  • Page 119 NO-TRIM-JUMP LOCK SHAFT WHEN STOP Choice: Y(YES), N(NO) SPEED 1 PRE-TRIM Choice: 60~600 SPEED 2 PRE-TRIM Choice: 60~600 STARTUP FILTER EMPTY Choice: Y(YES), N(NO) BUZZING AFTER T.B Choice: Y(YES), N(NO) STATIC TRIM ANGLE Choice: 86,100 BECS-328 Computerized Embroidery Machine's Manual...

  • Page 120: Appendix: All Functions In Different Modes

    Frame returning to the origin point Frame returning to stop-embroidery point Manual thread trimming Set main shaft acceleration speed Set main shaft deceleration speed Manual color-change (needle-change) Turn the main shaft at 100 degree manually Clear stitch count frame BECS-328 Computerized Embroidery Machine's Manual...
  • Page 121 Formatting a 720KB diskette FORMAT 1.44M Formatting a 1.44MB diskette INSTALL LETTER LIBS Installing the letter library DELETE LETTER LIBS Deleting the letter library DESIGN A LETTER PATTERN SELECT DESIGN FOR EMB. **(31-40 DESIGN MANAGEMENT) BECS-328 Computerized Embroidery Machine's Manual...
  • Page 122 Combine the patterns in memory PACKED DESIGN Edit the packed pattern CLEAR ALL Clear all patterns in memory SET DESIGN PARAS (parameters) **(41-56 OTHER MANAGEMENT) FRAME TO POINT DESIGN RANGE’S OPERATIONS OFFSET SET POWER RESUME BECS-328 Computerized Embroidery Machine's Manual...
  • Page 123 Mode Mode Mode Instantly POWER RESUME SET MACHINE PARAS COMPENSATION DHINESE/ENGLISH TO SET CYCLE EMB. ON/OFF HI-SPEED DESIGN COMPILE PACKED DESIGN COMPILE EMBROIDER. DESIGN FRAME TO MAKE DESIGN ADD PATCH CODE TO DESIGN ADJUST BRAKE BECS-328 Computerized Embroidery Machine's Manual...
  • Page 124 文件名称 版 本 号 发布日期 软件版本 328GK00I1E11.ROM 翻 译 校 准 审 核...

Table of Contents

Save PDF