Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Vdab200 EverSmooth
- Page 1 User Guide...
-
Page 2: Table Of Contents
Table of Contents R E A D C O M P L E T E L Y B E F O R E U S E PARTS LIST OUR STORY LOADING YOUR Vdab200 TIPS CARE BATTERY WARRANTY, RETURNS and DISCLAIMER CONTACT US... - Page 3 Some materials harden much like cement when cold. Forcing the plunger out can leave behind the plunger’s plastic tip. But if this happens don’t fret. Warm load chamber and use back end of scoop to push out plastic end. Contact us for a replacement tip at www.vdab200.com.
-
Page 4: Parts List
PARTS LIST Mouth Plunger Sleeve Dual Base Load Scoop Stand Chamber Coil Charger Tamper 510 vv Battery Bonus Parts: 2 spare dual coils 2 spare O-rings... -
Page 5: Our Story
OUR STORY The Vdab200 story starts with an engineer who knew there must be a better way to vape without the constant hassle and mess of reloading after only a few draws. Lucky for us, perseverance paid off and the first Vdabs are here! The Vdab200 elegantly delivers a discreet, hassle free, EverSmooth™... -
Page 6: Loading Your Vdab200
LOADING YOUR Vdab200 1. Disassemble Vdab: Pull SLEEVE off BASE (leave COIL attached to base). Pull MOUTH TIP off PLUNGER . Fully untwist plunger handle. Unscrew sleeve from plunger. Pull LOAD CHAMBER from sleeve. 2. Prepare and Load Material: A. Roll ”... - Page 7 3. Use flat end of TAMPER Compress Material with Tamper push material down into the load chamber. Chamber holds 1 gram. Tip: Rub a touch of food-grade oil on tamper Max Fill Groove to prevent sticking. Continue adding material up to ”...
- Page 8 6. Twist plunger handle slowly until a small dab protrudes from chamber. Watch through sleeve for small dab to protrude from chamber Twist clockwise while twisting plunger handle 7. Rub a touch of food-grade oil onto PLUNGER and BASE o-rings. 8.
-
Page 9: Use
1. Hold the power button several seconds to melt material onto wick. 2. Your Vdab is now ready for 4-8 draws. To reload, twist tip clockwise turn. Do not overload coil. 3. The load chamber is empty when tip no longer turns. (See CARE to refill.) 4. -
Page 10: Tips
TIPS 1. Over-loading the coil causes clog and waste. 2. Before sliding sleeve off to view coil or chamber tip, heat Vdab a few seconds, or damage to wick is possible. Hold upright, remove slowly. Note: This action breaks the thread of material that can form between the coil and chamber tip. -
Page 11: Care
CARE CRITICAL: Warm Vdab200 before removing plunger from chamber. 2. Pull Vdab atomizer off from base and pull off mouth tip. 3. Unscrew sleeve from plunger. 4. Grasp chamber and pull plunger out. Reheat if it does not extract easily. -
Page 12: Battery
BATTERY 1. The 510 thread, 900mAh, vv battery comes pre-charged. To fully charge, remove cover ring from head and attach charger to head. 2. Rapidly press power button five times to power on/off. 3. Adjust voltage from 3.2v to 4.8v, to your preference, using the bottom Click™... -
Page 13: Warranty, Returns And Disclaimer
Disclaimer: Organic materials react differently to heat. QanTeq Inc. is not responsible for consumer’s actions, or for the reaction of the Vdab200 or accessory parts, to any material used therein or therewith. -
Page 14: Contact Us
CONTACT US Call: 844.8.Vdab200 Email: help4u@vdab200.com Go to www.vdab200.com to order replacement parts, coils and accessories and to find out more about the Vdab200 Follow us on Twitter: @vdab200 Watch our instruction video: Youtube channel vdab200 For further information about the Click™ battery, see www.c-tratech.com Sincerely EverSmooth, ™... - Page 15 PO Box 10788 • Zephyr Cove • NV 89448...
Need help?
Do you have a question about the EverSmooth and is the answer not in the manual?
Questions and answers