1. Manuals
  2. Brands
  3. Saniwise Manuals
  4. Toilets
  5. F6
  6. User manual

Saniwise F6 User Manual

Bidet seat
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Bidet Seat F6 User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the F6 and is the answer not in the manual?

Questions and answers

Related Manuals for Saniwise F6

Summary of Contents for Saniwise F6

  • Page 1 Bidet Seat F6 User Manual...

  • Page 2: Table Of Contents

    Maintenance Self-diagnosis and Troubleshooting Warranty Record Saniwise Warranty Thank you for purchasing Saniwise Bidet Seat. Please read through this manual carefully to ensure the safe use of your product. Keep this manual in a safe place for your future reference.

  • Page 3: Parts And What's In The Box

    Parts and What’s in the Box Parts Water inlet on the left Dismantle button Seat cover Water tank Lever Seat T-shaped adapter Bidet nozzle Wash nozzle Water supply hose Bowl Shutoff valve Water inlet hose...

  • Page 4: What's In The Box

    User Manual Filter Note There are two methods to install the Saniwise Bidet Seat. It is recommended that you use expansion nuts. You can also use butterfly nuts. Please choose the appropriate installation method according to your specific installation needs.

  • Page 5: Caution

    Please read the following instructions carefully and install your Saniwise Bidet Seat properly. Caution 1. The water pressure limit ranges from 10 to 110 PSI. Please use as instructed. 2. The water shutoff valve should be near where the product can be installed and dismantled.

  • Page 6: Installation Procedures

    6. Mount the Saniwise Bidet Seat. Keep the fixing slots under the Saniwise Bidet Seat aiming at the slots on the adaptable panel. Push the Saniwise Bidet Seat to the end. Now, the Saniwise Bidet Seat is installed Installation template successfully.

  • Page 7: Connecting Water Inlet Hose

    Connecting Water Inlet Hose 2. Unscrew the water supply hose from the water 1. Turn off the water supply valve. tank. Place a towel below the tank to catch any dripping water. Unscrew to remove 3. Using finger nut, attach the T-shaped connector 4.
  • Page 8 7. Wipe the hoses and connectors thoroughly with a towel and carefully observe for any leaks for at least 10 minutes. Tighten any connectors gently until leakage stops. If any leaks continue, turn off the water supply and check older hoses for damaged rubber O-rings and replace them if necessary. *Optional, only do the following if water pressure is too low.

  • Page 9: Extra Installation Tips

    6 in the instructions and it will explain how to remove the pressure regulator and dramatically increase the pressure. If you still need help, feel free to send us an email at support@saniwise.com.

  • Page 10: Functions

    Functions WASH (REAR WASH) 1) Turn the lever clockwise from the vertical position. 2) The nozzle for rear wash extends forward, and the freshwater spray function starts. 3) The water volume decreases while turning the lever towards the vertical position. It will totally shut off when the lever is on the vertical position. BIDET (FRONT WASH) 1) Turn the lever counterclockwise from the vertical position.

  • Page 11: Cleaning And Dismantling

    4. Dismantle the Saniwise Bidet Seat. Close the cover. Push the dismantle button (If the water flow is less than usual) and pull the Saniwise Bidet Seat forward, 1) Turn off the water supply, remove the as shown in the figure below.

  • Page 12: Maintenance

    Maintenance 1. Lever Replacement 2. Nozzle Replacement 1) Remove the old lever as shown in figure A. 1) Pull out the tube and hold it, then remove 2) Insert the new lever rib into the the old nozzle, as shown in figure A. corresponding slot.

  • Page 13: Self-Diagnosis And Troubleshooting

    If the pressure of the water supply is higher than that, please contact during usage. high. your local water department. If the failure still occurs after the solutions above have been taken, please contact Saniwise by sending an email to support@saniwise.com. Do not disassemble, repair, or remodel the Saniwise Bidet Seat. Caution Specifications Model No.

  • Page 14: Warranty Record

    Warranty Record Dear customer, Thank you for choosing Saniwise. If any failure or issue occurs, please check your Saniwise Bidet Seat following the troubleshooting methods in this manual first. If the failure or issue cannot be fixed, please follow the return instructions on the next page.

  • Page 15: Saniwise Warranty

    Saniwise Bidet Seat not caused directly by the negligence of Saniwise. This limited warranty shall not extend to anyone other than the original purchaser of the Saniwise Bidet Seat.

Table of Contents