Application Advice; Maintenance & Service; Noise / Vibration - Skil 6225 Original Instructions Manual

- position F will lock up the clutch to permit impact drilling
only
! ensure that gear selector G is in position HIGH
when clutch ring D is in impact drilling position
! do not use impact drilling position F for drilling in
wood, metal, ceramic and plastic to prevent the
drill/screw bit from being damaged
• Mechanical gear selection w
- set selector G to desired speed
! actuate the gear selector while tool is running
slowly
LOW
- low speed
- high torque
- for screwdriving and drilling large diameters
- for tapping thread
HIGH
- high speed
- lower torque
- for drilling small diameters
• Holding and guiding the tool e
! while working, always hold the tool at the grey-
coloured grip area(s)
- keep ventilation slots H 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you

APPLICATION ADVICE

• Use the appropriate bits r
! only use sharp bits
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
• For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
• When screwdriving in hard wood one should pre-drill a
hole
• Splinterfree drilling in wood t
• Dustfree drilling in walls y
• Dustfree drilling in ceilings u
Drilling in tiles without skidding i
•
• For more tips see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots G 2 )
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs

NOISE / VIBRATION

• Measured in accordance with EN 60745 the sound
pressure level of this tool is 82 dB(A) and the sound
power level 93 dB(A) (standard deviation: 3 dB), and the
vibration ✱ (triax vector sum; uncertainty K = 1.5 m/s²)
when drilling in metal < 2.5 m/s²
✱
when impact drilling in concrete 12.5 m/s²
✱
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
Perceuse à percussion/visseuse 6225
INTRODUCTION
• Cet outil est conçu pour les travaux perçage de
percussion dans la brique ainsi que le perçage dans le
bois, le métal, la céramique et les matières plastiques;
les outils avec réglage électronique de la vitesse et
rotation à droite/à gauche sont également appropiés
pour le vissage et le filetage
• Cet outil n'est pas conçu pour un usage professionnel
Lisez et conservez ce manuel d'instruction 3
•
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Interrupteur de marche/arrêt et réglage de vitesse
B Commutateur pour inverser le sens de rotation
C Mandrin auto-serrant
D Anneau pour réglage du couple
E Position de perçage
F Position de perçage à percussion
G Commutateur de vitesse
H Fentes de ventilation
10