Gira 2461 Series Operating Instructions

Operating instructions
Bluetooth wall transmitter
1-gang 2461 ..
2-gang 2462 ..
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 12 20
42461 Radevormwald
Deutschland
Tel +49(0)21 95 - 602-0
Fax +49(0)21 95 - 602-191
www.gira.de
info@gira.de
TOP
1 2 3 4
1
TOP
1 2 3
2
Bluetooth wall transmitter
Safety instructions
Failure to observe the instructions can
result in damage to the device, fire or
other dangers.
Wireless transmission takes place via a
non-exclusive transmission path and is
thus not suitable for applications in the
security technology sector such as emer-
gency-off or emergency calls.
These instructions are part of the product
and must stay with the customer.
Device components
(Figure 1, 2)
1 Rocker
2 Wireless module
3 Cover frame
4 Base plate
5 Adhesive dots
6 Adhesive film
Function
System information
The range of a wireless system depends on
various external factors. This range can be
optimised by the ideal choice of the installa-
tion site.
TOP
Materials
Wood, plaster,
sheetrock
Brick, press board
Reinforced con-
crete
Metal, metal grids
Rain, snow
5 6
Intended use
- Wireless transmitter that communicates
according to the BLE wireless standard.
- Installation on device box in compliance
with DIN 49073 or on smooth, level surfa-
ces using screws or adhesive bonding.
TOP
Product properties
- Battery-free device without external power
supply.
- The transmission energy is generated from
mechanical energy by actuating the rocker.
Operation
Transmitting wireless telegrams
Press and release the rocker to send a wi-

reless telegram.
4
Electrical devices may only be
installed and connected by a qua-
lified electrician.
Penetration
approx. 90 %
approx. 70 %
approx. 30 %
approx. 10 %
approx. 1 to 40 %
Installation
To achieve good transmission quality, ensure
sufficient distance to possible sources of
interference, e.g. metal surfaces, microwave
ovens, hi-fi systems, TV sets, ballasts and
electronic transformers.
I Note
A higher contact pressure is requi-
red for initial installation.
Observe TOP designation.
Adhesive mounting (Figure 1)
Ensure that the surface is clean, free of gre-

ase and able to bear the load.
Apply the adhesive film (6) beforehand in

the case of transparent surfaces.
Apply adhesive dots (5) to the surface or to

the adhesive film (6) in the case of transpa-
rent surfaces.
Press the baseplate (4) onto the adhesive

dots.
Plug the frame (3) onto the baseplate.

Attach the wireless module (2).

Attach the rocker (1).

Screw mounting (Figure 2)
Mount the baseplate (4) on a device box or

directly on the wall.
Plug the frame (3) onto the baseplate.

Attach the wireless module (2).

Attach the rocker (1).

Start-up
Assignment of wireless wall transmitter
and wireless receiver
In order for a wireless receiver to understand
a wireless telegram from the wireless wall
transmitter, this wireless telegram must be
assigned to the wireless receiver (see instruc-
tions for wireless receiver).
Technical data
Ambient temperature: -25 to +65 °C
Wireless frequency 2.402 ... 2.480 GHz
Transmission power max. 1.1 mW /
0.4 dBM
Transmission range
in free field: up to 75 m
in buildings: approx. 10 m
Humidity: 0 % to 95 %
(no condensation)