1. Manuals
  2. Brands
  3. Adaptive Manuals
  4. UPS
  5. Tripp-Lite 1109502801
  6. Replacing manual

Adaptive Tripp-Lite 1109502801 Replacing Manual

Billboard
Hide thumbs
1
2
3
4
5
6

Advertisement

Table of Contents

Replacing the Billboard UPS
(PN 1109502801SP)
The billboard UPS (Uninterruptible Power Supply) is a 1500VA (Volt Amp) rack mounted
intelligent UPS that prevents data loss, downtime, and equipment damage due to power
outages, voltage fluctuations, and transient surges. The UPS resides inside the deluxe
remote control cabinet and provides back up power for a limited time to all the components
plugged into it.
The UPS software and SNMP / Web card allows billboard operators to remotely monitor
control cabinet equipment plugged into the UPS. Power can be cycled on and off on two sets
of UPS receptacles (load 1 and 2) allowing for a remote reboot of critical components.
Another feature of the UPS is the capability to view the control cabinet's ambient
temperature / humidity logs.
Before you begin
Kit contents
Part Number
1109502801
11099001
Mounting brackets
1109610110
Tools / Safety equipment needed
Full body safety harness with lanyard
#2 Phillips screwdriver
M
21, 2008
AY
Figure 1: Front view of billboard UPS.
Qty
1
1500VA rack mounted UPS.
1
SNMP / Web card (factory installed).
2
Mounting brackets and screws used to mount the UPS in the cabinet.
1
Instructions
Adaptive Micro Systems • 7840 North 86th Street • Milwaukee, WI 53224 USA • 414-357-2020 • 414-357-2029 (fax) • http://www.adaptivedisplays.com
Adaptive is a registered trademark of Adaptive Micro Systems. MEDIAMaster is a trademark of Adaptive Micro Systems.
Description
© Copyright 2008 Adaptive Micro Systems LLC. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective companies.
PN 1109610110
. A
REV

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Tripp-Lite 1109502801 and is the answer not in the manual?

Questions and answers

Summary of Contents for Adaptive Tripp-Lite 1109502801

  • Page 1 © Copyright 2008 Adaptive Micro Systems LLC. All rights reserved. Adaptive Micro Systems • 7840 North 86th Street • Milwaukee, WI 53224 USA • 414-357-2020 • 414-357-2029 (fax) • http://www.adaptivedisplays.com Adaptive is a registered trademark of Adaptive Micro Systems. MEDIAMaster is a trademark of Adaptive Micro Systems.
  • Page 2 EPLACING THE ILLBOARD Replacing the UPS WARNING! Possible fall hazard. When servicing billboard components, service personnel must use a full body safety harness with lanyard. Connect the lanyard to the billboard head’s safety cables; otherwise serious injury or death may occur. Hazardous voltage.
  • Page 3 EPLACING THE ILLBOARD 4. Remove the UPS from the control cabinet. • Remove the four UPS rack screws. Keep them for the replacement installation. Remove screws Figure 3: UPS rack mounting screw locations. • Pull the sliding UPS shelf out allowing it to support the weight of the UPS. Note: Do not force the shelf all the way out, otherwise power adapters tie wrapped to the shelf may become disconnected from their components.
  • Page 4 EPLACING THE ILLBOARD 8. Connect all previously removed cables. Item Port Component connection PC controller #1 power cord label ID #17. Load 1 (2 switched outlets) DVI / fiber converter #1 power cord label ID #8. PC controller #2 power cord label ID #22. Load 2 ** B (2 switched outlets)
  • Page 5 EPLACING THE ILLBOARD Verifying UPS operation Confirm the following functions of the UPS. Access the UPS’s web console from a remote Internet connection. The UPS LEDs indicate normal operating status. Item Normal indicating status Power Continuous green LED. Voltage correction Green LED is either continuous, blinking, or not lit at all.
  • Page 6 EPLACING THE ILLBOARD THIS PAGE INTENTIONALLY BLANK...

Table of Contents