Download
Share
Print this page
  1. Manuals
  2. Brands
  3. JW-System Manuals
  4. Keyboard
  5. ACT8 Series
  6. Manual

JW-System ACT8 Series Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
ACT8XX Manual
Contents
6.Commands
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the ACT8 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for JW-System ACT8 Series

  • Page 1: Table Of Contents

    ACT8XX Manual Contents 1.Information 2.Introduction 3.Installation 4.Pin Assignment 5.Operations 6.Commands 7.Specification...

  • Page 2: Information

    1.Information A. Model Classification: ACT 8 ○ ○ ○ ○ ○ ○ Model name: ○ Model number: 8 ○ Keypad type: 0 12 Keys 1 16 Keys 2 20 Keys ○ Reader type: 0 without reader 2 MAG TK2 3 MAG TK1+TK2 This device complies with Part 15 of the FCC .

  • Page 3: Introduction

    2.Introduction Three in one ACT8XX is a compact designed product with the combination of Number keyboard, Reader, and LCD. Three in one device saves installation space and provides easy operation. The product, designed with the state-of-the-art microprocessor and barcode/magnetic stripe card reader technology, is totally compatible with RS-232C interface.

  • Page 4: Pin Assignment

    4.Pin Assignment A. DB-9(female) pin B. DC power jack Pin# Signal Pin# Signal In from next stage Center(D2.1mm) +9V~+12VDC Outer GROUND Out to next stage GROUND Note: 4,6 short 7,8 short External Device RXD TXD ACT8XX Out to next stage 9 In from next stage 1 GND 5 RXD 2...

  • Page 5: Operations

    5.Operations When you start up ACT8XX, ACT8XX will set the boot-up status from memory (EEPROM). Then sound a beep and LCD shows the start-up page. After that, ACT8XX will stay at stand-by state. You can give a command to ACT8XX. For example, show a message to direct customer to do some action (refer to Paragraph 6-B command).
  • Page 6 6.Communications Command symbols definitions are as below: NACK 1 byte parameter 1 byte parameter <Data…> contents of data (command list) Command Hexadecimal Format Description STX V ETX Get device firmware version & status STX Dmn ETX Show pre-saved message page on LCD STX C ETX Erase LCD and buffer STX Mn ETX...
  • Page 7 B. Show pre-saved page message on LCD HOST to DEVICE (5 bytes) 44H bin bin 03H ACK/NACK DEVICE to HOST (1 bytes) m: text page message, m=30H; graphic page message, m=31H page number, 31H<=n=3CH(for m=30H, text page); 31H<=n<=36H(for m=31H, graphic page) You can show page message, which is kept in EEPROM, on your LCD.
  • Page 8 n=31H, Enable keypad(default) n=30H, Disable keypad Device will keep this setting in EEPROM. Device use the last setting for its setting when restart. Device will reply ACK, if this command is acknowledged. Otherwise, reply NACK. Note: Keypad is always enabled when the units restarted even though you did disable the keypad last time.
  • Page 9 I. Blink the display HOST to DEVICE (3 bytes) DEVICE to HOST (1 bytes) ACK/NACK Display will blink by this command, until the device is interrupted by next operation, like communication, key-in, …etc. Device will reply ACK, if this command is acknowledged. Otherwise, reply NACK. J.
  • Page 10 within the most upper sector and the second upper sector and then go to the third upper sector. (4)When YLEN is more than 24 dots(18H) and less than or equal to 32 dots(20H), the YLEN should be divided by 8 into four sectors. Then the block image data should be made as the same procedures as above within the most upper sector and the second upper sector and the third upper sector and then go to the last(bottom) sector.

  • Page 11: Specification

    7.Specifications emperature: 5 – 45 Degree C Humidity: 10 – 90 % Relative Size: W 105 XL 185 XH 40 mm Weight: 405 g Communication: RS – 232...

This manual is also suitable for:

Act810-jw