Advertisement

MB130 IDTV
SERVICE MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MB130 IDTV and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for VESTEL MB130 IDTV

  • Page 1 MB130 IDTV SERVICE MANUAL...
  • Page 2: Table Of Contents

    Table of Contents INTRODUCTION ................................3 General Block DIagram .............................. 4 Placement of Blocks ..............................5 T/T2/C/A TUNER (U118) .............................. 6 S/S2 TUNER (U116) OPTIONAL ..........................8 AUDIO AMPLIFIER STAGES ............................9 MAIN AMPLIFIER (U123) (8W/10W/12W options) ....................10 HEADPHONE AMPLIFIER (U120) ..........................12 SCART AUDIO AMPLIFIER (U119) ..........................
  • Page 3 USB Problems ................................44 No Sound Problem ..............................45 Standby On/Off Problem ............................46 İ. No SIgnal Problem ..............................46 14. SERVICE MENU SETTINGS ............................. 48...
  • Page 4: Introduction

    1. INTRODUCTION 17MB130 main board is driven by MStar SOC. This IC is a single chip iDTV solution that supports channel decoding, MPEG decoding, and media-center functionality enabled by a high performance AV CODEC and CPU. This board can be driven just 50Hz UHD panels. Key features include: ...
  • Page 5: General Block Diagram

    A. GENERAL BLOCK DIAGRAM BACKLIGHT_DIM 3D_SYNC_OUT KEYBOARD PANEL_VCC TOUCHPAD UART AMP_RST 1V5_VCC 1V5_VCC HP_DETECT HP_AMP_MUTE PC_SCL/SDA PCM_PWR_CTRL 3D_ENABLE STBY_ON/OFF RX/TX_HOTEL 12V/24V_VCC AUX_RESET TUN_RESET 2Gb DDR3 2Gb DDR3 FLASH_WPN1 HDMI DET SYS_SCL MEMORY MEMORY PROTECT USB-ENABLE SYS_SDA ESMT BACKLIGHT AD82587D PANEL_VCC RESET_HUB 2X6W/8W/ TUNER_RESET...
  • Page 6: Placement Of Blocks

    B. PLACEMENT OF BLOCKS Power Con. FLAS MAIN Sat. Tuner HDMI RJ45 Connectors Tuner S/PDIF Keyb 3-WAY oard SCART Internal SPEAK. Wifi& BT Audio Connector...
  • Page 7: T/T2/C/A Tuner (U118)

    2. T/T2/C/A TUNER (U118) Description: The Si2151 is Silicon Labs' sixth-generation hybrid TV tuner supporting all worldwide terrestrial and cable TV standards. Requiring no external balun, SAW filters, wirewound inductors or LNAs, the Si2151 offers the lowest-cost BOM for a hybrid TV tuner. Also included are an integrated power-on reset circuit and an option for single power supply operation.
  • Page 9: S/S2 Tuner (U116) Optional

    3. S/S2 TUNER (U116) OPTIONAL Description Figure: Pin description Features  Single-Chip tuner  Compliant with DVB-S2 and ABS-S standards  Support PSK, (PSK and 16APSK  Direct-conversion from L-band to baseband  Symbol rate:1 to 45 Msybol/s  Integrated VCOs and PLL, with on-chip inductors varactors and loop filter ...
  • Page 10: Audio Amplifier Stages

    Block Diagram 4. AUDIO AMPLIFIER STAGES Figure: The block diagram of the audio part...
  • Page 11: Main Amplifier (U123) (8W/10W/12W Options)

    A. MAIN AMPLIFIER (U123) (8W/10W/12W OPTIONS) Description AD82587D is a digital audio amplifier capable of driving a pair of 8 ohm, 20W or a single 4 ohm, 40W speaker, both which operate with play music at a 24V supply without external heat-sink or fan requirement. Using I C digital control interface, the user can control AD82587D’s input format selection, DRC (dynamic range control), mute and volume control functions.
  • Page 12 Figure 3.2: Pin description Figure 3.3: Functional Block Diagram Table3.1: Absolute Maximum Ratings...
  • Page 13: Headphone Amplifier (U120)

    Table3.2: Recommended Operating Conditions B. HEADPHONE AMPLIFIER (U120) Description The AD22657B is a 2-Vrms cap-less stereo line driver. The device is ideal for single supply electronics. Cap-less design can eliminate output dc-blocking capacitors for better low frequency response and save cost. The AD22657B is capable of delivering 2-Vrms output into a 10k ohm load with 3.3V supply.
  • Page 14: Scart Audio Amplifier (U119)

     External Under Voltage Protection  Thermal Protection  Less External Components Required  +/-8kV IEC ESD Protection at line outputs Figure: Pin description Table: Pin functions Table: Recommended operating conditions C. SCART AUDIO AMPLIFIER (U119) AD22657B is used for scart audio amplifier, as well.
  • Page 15: Power Stage

    5. POWER STAGE Figure: Power Block Diagram Figure: Power Socket and Power Options Power socket is used for taking voltages which are 24V_VCC, 12V_STBY and 5V_STBY. These voltages are produced in power card. Also socket is used for giving dimming, backlight and standby signals with power card.
  • Page 16 Figure: Power Block Diagram List of the components:  SW-1(Q105) → FDC642P  SW-2(Q100) → NTGS3446  DC-DC-1(U101) → RT7278G  DC-DC-2(U100) → TPS563200  DC-DC-3(U107) → TPS563200  DC-DC-4(U103) → TPS54821  DC-DC-5(U104) → TPS563200  LDO-1(U112) → AP2111H...
  • Page 17: Fdc642P

    A. FDC642P Figure: Pin description B. NTGS3446 Features  Ultra Low R DS(on)  Higher Efficiency Extending Battery Life  Logic Level Gate Drive  Diode Exhibits High Speed, Soft Recovery  Avalanche Energy Specified  IDSS Specified at Elevated Temperature ...
  • Page 18 Figure 4.7: Pin description Table 4.8: Maximum ratings...
  • Page 19: Rt7278G

    C. RT7278G Figure: Pin Assignment...
  • Page 21: Tps563200

    D. TPS563200 Figure: Pin Assignment...
  • Page 22 Electrical Characteristics...
  • Page 23: Tps54821

    E. TPS54821 General Description The TPS54821 in thermally enhanced 3.5 mm x 3.5 mm QFN package is a full featured 17 V, 8 A synchronous step down converter which is optimized for small designs through high efficiency and integrating the high-side and low-side MOSFETs. Further space savings are achieved through current mode control, which reduces component count, and by selecting a high switching frequency, reducing the inductor's footprint.
  • Page 24 Table 4.5: Recommended operating conditions Figure 4.5 : Pin Description...
  • Page 25 Table 4.6: Pin functions. F. AP2111 General Description The AP2111 is CMOS process low dropout linear regulator with enable function, the regulator delivers a guaranteed 600mA (Min) continuous load current. The AP2111 provides 1.2V, 1.8V, 2.5V, 3.3V, 4.8V regulated output and 0.8V to 5V adjustable output, and provides excellent output accuracy 1.5%, it is also provides a excellent load regulation, line regulation and excellent load transient performance due to very fast loop response.
  • Page 26: Microcontroller

    6. MICROCONTROLLER A. MSTAR G10 MSD95PMVW4 (U114) Description Features...
  • Page 33 Table: Recommended operating condition...
  • Page 34: Ddr3 Sdram

    7. 2GB DDR3 SDRAM A. HYNIX H5TQ2G63GFR-TEC (U113-U110) Description The H5TQ2G63GFR is a 2,147,483,648-bit CMOS Double Data Rate III (DDR3) Synchronous DRAM, ideally suited for the main memory applications which requires large memory density and high bandwidth. Hynix 2Gb DDR3 SDRAMs offer fully synchronous operations referenced to both rising and falling edges of the clock.
  • Page 35: Gbit - 4Gbit(Connected Option) (256M X 8 Bit) Nand Flash Memory

    Memory Configuration of MB130 Memory Config NAND Name RAM Internal RAM external Flash Flash Connected 2X2GBit 2X4Gbit 4Gbit 2MByte Non-Connected G10V 2X2Gbit 2Gbit 2MByte 8. 2GBIT - 4GBIT(CONNECTED OPTION) (256M X 8 BIT) NAND FLASH MEMORY A. MT29F2G08ABAEAWP (U105) Description Micron NAND Flash devices include an asynchronous data interface for high-performance I/O operations.
  • Page 36 o Page size x16: 1056 words (1024 + 32 words) o Block size: 64 pages (128K + 4K bytes) o Plane size: 2 planes x 1024 blocks per plane o Device size: 2Gb: 2048 blocks  Asynchronous I/O performance WC: 20ns (3.3V), 25ns (1.8V) ...
  • Page 37: M-Bit [16M X 1] Cmos Serial Flash Eeprom

    o VCC: 1.7–1.95V  Operating temperature: o Commercial: 0°C to +70°C o Industrial (IT): –40ºC to +85ºC  Package o 48-pin TSOP type 1, CPL63-ball VFBGA Table: Recommended operating conditions 9. 16M-BIT [16M X 1] CMOS SERIAL FLASH EEPROM A. KH25L1606EM2-12G MACRONIX SPI FLASH (U115) Description The device features a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus.
  • Page 38: Usb Interface

    Any Sector can be erased individually  32 Equal Blocks with 64K byte each Any Block can be erased individually  Program Capability Byte base Page base (256 bytes)  Latch-up protected to 100mA from -1V to Vcc +1V Figure: Pin configuration Table: Pin description 10.
  • Page 39: Usb Power Switch Tps2553-1 (U109-U117-U122)

    A. USB POWER SWITCH TPS2553-1 (U109-U117-U122) 11. CI INTERFACE 17MB130 Digital CI ve Smart Card Interface Block diagram:...
  • Page 40: Software Update

    Figure: CI interface 12. SOFTWARE UPDATE A. MAIN SOFTWARE UPDATE In MB98 project, please follow software update procedure: 1. mb130_en.bin, mb130_RomBoot.bin, mb130_PM51.bin and usb_auto_update_G10.txt documents should be copied directly inside of a flash memory (not in a folder). 2. Insert flash memory to the TV when TV is powered off. 3.
  • Page 41 Dimming pin should be high or square wave in open position. If it is low, please check S122 for Mstar side. It also can be checked at TP106. Please also check panel or power cables and connectors. Backlight power supply should be in panel specs. Please check Q124, shown below; also it can be checked TP112.
  • Page 42 STBY_ON/OFF should be low for TV on condition, please check Q114’s collector.
  • Page 43: Ci Module Problem

    B. CI MODULE PROBLEM Problem: CI is not working when CI module inserted. Possible causes: Supply, suply control pin, detects pins, mechanical positions of pins.  CI supply should be 5V when CI module inserted. If it is not 5V please check CI_PWR_CTRL, this pin should be low.
  • Page 44: Staying In Stand-By Mode

    C. STAYING IN STAND-BY MODE Problem: Staying in stand-by mode, no other operation. This problem indicates a short on Vcc voltages. Protect pin should be logic high while normal operation. When there is a short circuit protect pin will be logic low. If you detect logic low on protect pin, unplug the TV set and control voltage points with a multimeter to find the shorted voltage to ground.
  • Page 45: Keypad Touchpad Problems

    E. KEYPAD TOUCHPAD PROBLEMS Problem: Keypad or Touchpad is not working Check keypad supply on MB130. F. USB PROBLEMS Problem: USB is not working or no USB Detection. Check USB Supply, It should be nearly 5V. Also USB Enable should be logic high. USB Control is optional, so U109 and U117 may not be added.
  • Page 46: No Sound Problem

    G. NO SOUND PROBLEM Problem: No audio at main TV speaker outputs. Check supply voltages of 24V_VCC, VDD_AUDIO and 3V3_AMP with a voltage-meter. There may be a problem in headphone connector or headphone detect circuit (when headphone is connected, speakers are automatically muted).
  • Page 47: Standby On/Off Problem

    H. STANDBY ON/OFF PROBLEM Problem: Device cannot boot, TV hangs in standby mode. There may be a problem about power supply. Check main supplies with a voltage-meter. Also there may be a problem about SW. Try to update TV with latest SW. Additionally it is good to check SW printouts via Teraterm program.
  • Page 49: Service Menu Settings

    14. SERVICE MENU SETTINGS In order to reach service menu, first Press “MENU” buton, then write “4725” by using remote controller. You can see the service menu main screen below. You can check SW releases by using this menu. In addition, you can make changes on video, audio etc.
  • Page 50 Audio Settings Options 1...
  • Page 51 Options 2 Options 3...
  • Page 52 Tuning Settings Source Settings...
  • Page 53 Diagnostic...
  • Page 54 Close To TS2022 F124 3V3_VCC 3V3_VCC_SAT C380 C398 C364 C515 C385 C402 C365 100n 100n 100n 100n 100n 100n 100n VESTEL 17mb130p-r1 PROJECT NAME : SCH NAME : TUNER_SAT_LNB T. SHT: <YOUR NAME HERE> DRAWN BY : 20-06-2016_14:13 A X M...
  • Page 55 C396 BC848B 100n C423 220R R411 SC_CVBS_OUT CVBSOUT1 JK102 C438 F143 TP170 VGA_B F141 1k VGA_G F142 VGA_R CN112 VESTEL 17mb130p-r1 PROJECT NAME : SCH NAME : PERIPHERALs T. SHT: <YOUR NAME HERE> DRAWN BY : 20-06-2016_14:11 A X M...
  • Page 56 TPS2553-1 C5V6 100n R480 TP201 R374 5V_STBY WIFI/BT_ENABLE FAULT 560R USB_WIFI_DN Q130 HOTPLUG2 D134 TP200 D139 BC848B USB_WIFI_DP TP199 VESTEL 17mb130p-r1 PROJECT NAME : SCH NAME : HDMI_USB_ETH T. SHT: <YOUR NAME HERE> DRAWN BY : 20-06-2016_14:56 A X M...
  • Page 57 U108 AB_MRASn TP135 AB_MCASn AB_MODT RT9026GFP AB_MWEn DDR_VTT 3V3_VCC PGND C228 C222 C221 AB_RSTn RESET 100n VTTSNS VTTREF 100n C229 VESTEL 17mb130p-r1 PROJECT NAME : SCH NAME : T. SHT: <YOUR NAME HERE> DRAWN BY : 20-06-2016_11:04 A X M...
  • Page 58 R201 R173 PCM_A12 CI_A12 PCM_WAIT CI_WAIT PCM_A13 CI_A13 PCM_RST CI_RST PCM_A14 CI_A14 PCM_REG CI_REG PCM_IRQA CI_IRQA R208 PCM_IOWR CI_IOWR VESTEL 17mb130p-r1 PROJECT NAME : SCH NAME : CI_NAND T. SHT: <YOUR NAME HERE> DRAWN BY : 27-06-2016_11:26 A X M...
  • Page 59 TP228 SPI_SCL_BS BC848B TP229 SPI_SDI_BS TP230 SPI_SDO_BS Q142 Q143 SPI_XCS_BS BC858B 3-WAY KEYBOARD R116 BC858B R111 3V3_VCC R117 VESTEL 17mb130p-r1 PROJECT NAME : 5V_STBY SCH NAME : GPIOs_SPI T. SHT: <YOUR NAME HERE> DRAWN BY : 27-06-2016_15:27 A X M...
  • Page 60 G6F_VBY7N ACKM[B_ODD5]/VB1_7N R247 AH26 3V3_VCC G6F_VBY7P ACKP[B_ODD4]/VB1_7P AF25 G6F_LOCKN A3M[B_ODD3]/LOCKN AG25 G6F_HTPDN A3P[B_ODD2]/HTPDN AG24 3V3_VCC A4M[B_ODD1] VESTEL 17mb130p-r1 PROJECT NAME : AH24 R217 A4P[B_ODD0] SCH NAME : VBYONE T. SHT: <YOUR NAME HERE> DRAWN BY : 20-06-2016_10:18 A X M...
  • Page 61 C488 PVSS PVDD 150p F150 1k TP171 C457 3V3_VCC R447 C492 HP_DETECT 100R F146 3V3_VCC C484 3V3_STBY 3V3_VCC VESTEL 17mb130p-r1 PROJECT NAME : SCH NAME : AUDIO AMPs T. SHT: <YOUR NAME HERE> DRAWN BY : 20-06-2016_14:02 A X M...
  • Page 62 GND247 GND148 GS100 GND246 GND149 GND245 GND150 GS101 GND244 GND151 AB28 GND243 GND152 AB22 GND242 GND153 AB21 GND241 GND154 VESTEL 17mb130p-r1 PROJECT NAME : SCH NAME : MAIN_POWER T. SHT: <YOUR NAME HERE> DRAWN BY : 20-06-2016_10:18 A X M...
  • Page 63 C887 CORE_RESET 100n S209 R176 Q114 STBY_ON/OFF BC848B Q109 Q110 R165 2N7002 2N7002 CORE_VID0 12V_VCC VESTEL 17mb130p-r1 PROJECT NAME : C167 C165 R157 C164 C156 CORE_VID1 SCH NAME : POWER T. SHT: <YOUR NAME HERE> DRAWN BY : 27-06-2016_14:55 A X M...

Table of Contents

Save PDF