CharlesWater Jewel 99135 Installation, Operation And Maintenance

Jewel Workstation Continuous Mini Monitor
®
Installation, Operation and Maintenance
Figure 1. Charleswater
Continuous Mini Monitor.
Description
The Jewel Workstation Continuous Mini Monitor
®
independently monitors the operator and the
worksurface. The instant an operator's wrist strap or
cord fails, the monitor will issue audible and visual
alarms alerting the user of the problem. In the same
manner, the unit also confirms that a path to ground
of less than 500 megohms exists from the ESD
worksurface.
The Jewel Workstation Continuous Monitor is a Single
®
Conductor Impedance Sensing Continuous Monitor
which per ESD Handbook TR20.20 section 5.3.9.2.1 "a
small AC voltage is used in a detection circuit designed
to eliminate false alarms and adjustment. They use the
phase difference between current and voltage to detect
changes in impedance of the grounding cord, wristband
and person. No adjustments are required."
Per ESD Handbook ESD TR20.20 section 5.3.2.4.4,
"Typical test programs recommend that wrist straps that
are used daily should be tested daily. However, if the
products that are being produced are of such value that
knowledge of a continuous, reliable ground is needed,
and then continuous monitoring should be considered or
even required."
Advantages Of Continuous Monitoring
Over Periodic Testing
"When considering constant [or continuous]
monitors, the equipment cost including the wrist
strap, maintenance and training cost, labour time for
performing wrist strap tests, and the potential failures
due to non-functional wrist straps should be considered.
PPE-5098.E Page 1 of 4
June 2014
TECHNICAL BULLETIN PPE-5098.E
99135 Jewel Workstation
®
Unit 17. Millbrook Business Park, Sybron Way • Crowborough, East Sussex TN6 3JZ United Kingdom
Phone: 00 44 (0) 1892-665313 • Internet:
A broken wrist strap may expose products to ESD
over an entire shift if it is checked only at shift change
with wrist strap checker." (ESD TR 12-01 Section 4.2
Selection Considerations)
The Jewel Workstation Continuous Monitor eliminates
®
the need for periodic wrist strap tests and logging.
Continuous monitoring is superior to periodic or
pulsed testing, and can save a significant amount of
money in testing costs and rejected product. Periodic
testing detects failures after ESD susceptible products
have been manufactured. The costs of dealing with
the resulting catastrophic or latent defects can be
considerable. Jewel Workstation Continuous Mini
®
Monitors eliminate the need for operaters to test wrist
straps and log the results; by their function, these
monitors satisfy the ISO 9000 and ANSI/ESD S20.20
test logging. ANSI/ESD S20.20 Section 6.2.2.2
Personnel Grounding Guidance states "A log should be
maintained which verifies that personnel have tested
their personal grounding devices." Per ANSI/ESD-S1.1
Annex A Section 6.1.3 "Daily (wrist strap system) testing
may be omitted if constant monitoring is used." Per
ANSI/ESD-S1.1 Annex A Frequency of Functional
Testing, "The wrist strap system should be tested daily
to ensure proper electrical value. Daily testing may be
omitted if constant monitoring is used."
Park Snap
The audible alarm is designed to alert both operator and
supervisor. The Park Snap feature provides a means
for an operator to disconnect when normally leaving
the work area, without the audible alarm sounding, and
wrist cord storage (visual red LED will illuminate). When
the operator touches the Park Snap, the audible alarm
is disabled for about 8-10 seconds. The operator can
remove the wrist strap cord and attach socket of the
cord to Park Snap for storage. The coil cord may also
be removed from the jack on the Jewel
the alarm sounding. Once the coil cord is in the park
position, the operator ground status light will remain red.
Wave Distortion Detection Technology
Provides True 100% Continuous Monitoring
Wave distortion impedance circuitry monitors current /
voltage phase shifts and provides true 100% continuous
monitoring. Electrical current will lead voltage at various
points due to the combinations of resistance and
capacitive reactance. By monitoring these "distortions"
or phase shifts, the Jewel
Monitor will reliably determine if the circuit is complete.
Charleswater.co.uk
Made in the
United States of America
monitor without
®
Workstation Continuous Mini
®
© 2014 Charleswater