American Standard 4A6H5036E1000A Service Facts

rt'/w1i:au Svémdard
HEATING & AIR CONDITIONING
-:7:;:;._ _;:;:;:~ :;:_:;: ;:;:;:; 1:;;§~_,::;;- :;:;.;: ;:;:;:; _.;.;.;. :;:;t;: :;:_:;:; _:_<;:;' 7:;:;:;; :;;;:;; ;.;.;.» :I:1;- 7 _ "-'-I-f:§:I:~
"~;;:;:;:;:;.;.;._:;:7<~:~' :>:;;;t;.;.;.;:;:-:> ;:-:»:- ';:i:-:i:-: -:-:-:~ ;-;~:-:-_-_-_.;I;I;:- -1;1;';._._._._.;:»:;:~ :;:;:;:_ ~Z'I;I;._ _._.;:i:;:-. ;-:-:~... '-:-:~:. ...~:-:1
' -~ ~-:-.;:;:-:»'-" :-;»:-; '*2-1;:-:~'-'::-:-; '-:-:;;;:;: 1-" '-;<':;: :;:_;~:
Split System
4A6H5036E-SF-1 B
UNIT CONTAINS R-410A REFRIGERANTI
t . R-410A OPERATING PRESSURE exceeos THE
LIMIT OF R-22. PROPER SERVICE EQUIPMENT IS
REQUIRED. FAILURE TO use PROPER SERVICE
TOOLS MAY RESULT IN EQUIPMENT DAMAGE on
PERSONALINJURY.
Heat Pump
4A6H5036E1000A
' iT " Z i in I' I I "i' ' I I _ I 7 *'*' iq I ant" "' T .J@——
SERVICE
use ONLY R-410A REFRIGEFIANT AND
APPROVED POE COMPRESSOR OIL.
IMPORTANT --This document contains a wiring diagram, a parts list, and service information. This is customer prop-
7-E_B__QQyQ__T SEEQIFICATIQNS . 7
ourooon UNIT U23» 4A6H5036E1000A
POWER CONNS. — V/PH/HZ . / . - I i ' 208/230/1/60
MiN. BRCI-I. CIR. AMPACITY 20
BR. CIR. PROT. RTG7 — MAX. (AMPS) _ 7 7
COMPRESSOR
NO. USED - NO. SPEEDS
VOLTS/PH/HZ
R.L. AMPS Q7 - L.R. AMPS
FACTORY INSTALLED
START COMPONENTS @
INSULATION/SOUND BLANKET
COMPRESSOR HEAT
35
DURATIONTM
1 - 1
200/230/'I/60
15.4 - 83
NO
YES
YES 7 7
PROPELLER
27.6 - 1
DIRECT - 1
3820
1 - 1/5
ourooon FAN
DIA. (lN.) - no. useo
TYPE DRIVE - NO. SPEEDS
CFM @ 0.0 lN.W.G. to
NO. MOTORS - HP
MOTOR SPEED R.P.M.
VOLTS/PH/HZ
F.L. AMPS
SPINE FINT"
1 - 24
27.86
3/8
850
200/230/1/60
1 .00
ouToooi=i COIL - TYPE
nows - F.P.l.
FACE AREA (so. FT.)
TUBE SIZE .(lN-.). .
REFRIGERANT
LBS. -- R-410A (0.0. UNIT) I; 9 i.es., 3 oz.
FACTORY SUPPLIED YES
LINE SIZE - IN. 0.0. GAS 3/4
LINE SIZE - IN. O.D. LIO. @ 3/e
CHARGING SPECIFICATION
SUBCOOLING 10°F
DIMENSIONS i-i x w x o
CRATED(lN.)7 7 46.4x35.1x38.7 77
WEIGHT
SHIPPING (LBS.) 283
-.N_§T(LBS-)- __,._____ __ . _ _ _____2i7 . _
THIS INFORMATION IS INTENDED FOR USE BY INDIVIDUALS POS-
SESSING ADEQUATE BACKGROUNDS OF ELECTRICAL AND ME-
CHANICAL EXPERIENCE. ANY ATTEMPT TO REPAIR A CENTRAL AIR
CONDITIONING PRODUCT MAY RESULT IN PERSONAL INJURY AND
OR PROPERTY DAMAGE. THE MANUFACTURER OR SELLER CANNOT
BE RESPONSIBLE FOR THE INTERPRETATION OF THIS INFORMATION,
NOR CAN IT ASSUME ANY LIABILITY IN CONNECTION WITH ITS USE.
erty and is to remain with this unit. Please return to service information pack upon completion of work.
- ._TU7B!_I§I_GINF.08MATIQl)_|.--.._-.----,__
Tubing Sizes Tubing Additional
Suction Liquid . Length Refrigerant
3/4" 3/8" 20'
3/4" 3/8" 30'
3/4" 3/8" 40'
3/4" 3/8" 50' 19 OZ.
3/4" 3/8" 60' 24 OZ.
Tubing lengths in excess of sixty (60) feet see application software.
3 oz.
8 oz.
14 oz.
IL' Certified in accordance with the Air-Source Unitary Air-conditioner Equipment certifica-
tion program, which is based on ARI standard 210/240.
@ Rated in accordance with ARI standard 270.
@ Calculated in accordance with Natl. Elec. Codes. Use only HACR circuit breakers or
fuses.
G) Standard Air —- Dry Coil -- Outdoor
@ This value approximate. For more precise value see unit nameplate.
@ Max. linear length 60 ft.; Max. lift - Suction 60 ft.; Max lift ~ Liquid 60 ft.
For greater length consult refrigerant piping software Pub. No. 32-3312-0*
(* denotes latest revision).
£7) This value shown for compressor RLA on the unit nameplate and on this specification
sheet is used to compute minimum branch circuit ampacity and max. fuse size. The
value shown is the branch circuit selection current.
No means no start components. Yes means quick start kit components. PTC means
positive temperature coefficient starter.
*cAurioii\i»l A ~ *
CONTAINS REFRIGERANTI
SYSTEM CONTAINS OIL AND REFRIGERANT UNDER
HIGH PRESSURE. RECOVER REFRIGERANT TO RELIEVE
PRESSURE BEFORE OPENING SYSTEM.
Failure to follow proper procedures can result in personal
illness or injury or severe equipment damage.
A CAUTION
RECONNECT ALL GROUNDING DEVICES.
ALL PARTS OF THIS PRODUCT CAPABLE OF CONDUCTING
ELECTRICAL CURRENT ARE GROUNDED. IF GROUNDING
WIRES, SCREWS, STRAPS, CLIPS, NUTS OR WASHERS USED
TO COMPLETE A PATH TO GROUND ARE REMOVED FOR
SERVICE, THEY MUST BE RETURNED TO THEIR ORIGINAL
POSITION AND PROPERLY FASTENED.
NOTICE: Trane has a policy of continuous product and product data improvement and
it reserves the right to change design and specifications without notice.
© 2009 American Standard Heating & Air Conditioning
11/09