Advertisement
Quick Links
System Installation Instructions
Contents
S
o c
e p
H
a
d r
w
r a
c e
n o
e n
t c
y S
e t s
m
n i
t s
l l a
i t a
n o
A
d
u j
t s
m
n e
o t
t f
p o
Install the writing surface and paper tray
C
o
m
o p
e n
t n
p
a l
e c
m
C
n o
n
c e
t t
e h
E
e x
c r
Copyright © 2014 Mortara Instrument, Inc. All rights reserved.
o i
s n
n o
a
r t s
s s e
a c
t r
u s
a f r
e c
e h
g i
t h
e
t n
e s i
D
e
i v
e c
Q-Stress 4.5
REF: 70-00261-02 Rev D1
3
4
7
8
10
1 1
7 1
1
Advertisement
Summary of Contents for Mortara Instrument Quinton Q-Stress 4.5
- Page 1 Q-Stress 4.5 System Installation Instructions REF: 70-00261-02 Rev D1 Copyright © 2014 Mortara Instrument, Inc. All rights reserved. Contents e t s l l a i t a r t s s s e a f r Install the writing surface and paper tray...
- Page 2 Trademark Information Quinton, Burdick, HeartCentrix‚ Q-Stress, and HeartStride are trademarks or registered trademarks of Mortara Instrument, Inc. All other product and company names are trademarks or registered trademarks of their respective companies. Copyright © 2014 Mortara Instrument, Inc. All Rights Reserved.
- Page 3 Scope Scope is document describes the assembly of a Stress system. It is designed to be used as a whole for the installation process or in part as a troubleshooting tool for ensuring correct connection, configuration, and functioning of the Stress system. Because the Stress system can be purchased in different configurations and with different options, your system’s feature set may be different from the feature set shown in this document.
-
Page 4: Hardware Connections
Q-Stress 4.5 System Installation Instructions Hardware connections Caution. The following cautions apply: The computer, monitor, preamp, and printer must be plugged into the isolation transformer. The preamp and printer must be plugged into the A outlets and the computer and monitor (or computer and power strip on units equipped with the optional external hard disk) must be plugged into the B outlets. - Page 5 Hardware connections AC Wall AC Wall Power Treadmill Outlet Outlet Data Uninterruptable Isolation Remote Power Supply Transformer Keypad (optional) (Optional) Preamp II Monitor Power Patient supply Cable Keyboard Computer Laser Printer Chart Recorder Parallel RS-232 Preamp II Mouse QRS Synch Blood RS-232 Pressure...
- Page 6 Q-Stress 4.5 System Installation Instructions Computer and Preamp II connections Port Connect to AC Power Unused Unused Keyboard Mouse (PS/2) USB printer (HP laser printer) Parallel printer with HASP (TCR-1000 chart recorder) Unused COM 1 Blood pressure monitor (optional) Record connections to COM ports for use in system setup. Note: COM 4 for Preamp II;...
- Page 7 System installation on a stress cart System installation on a stress cart The steps below show how to place Stress system components on a Q-Stress cart. If you are not placing your system on a cart, you can use these steps for instructions on connecting the different components.
- Page 8 Q-Stress 4.5 System Installation Instructions Adjustment of top surface height Follow the instructions below to change the height of the top surface. Be aware that some of the screws are located in awkward positions. e pictures below show the top surface changed from the higher to the lower height.
- Page 9 System installation on a stress cart Step Turn the top surface over and lay it on the cart (or a flat area). Remove the screws connecting each riser to the top surface Rotate each riser 90 degrees and fasten back to the top surface Turn the top surface so the risers are on the bottom and lined up with the holes on top of the cart.
- Page 10 Q-Stress 4.5 System Installation Instructions Install the writing surface and paper tray Follow these instructions to install the optional writing surface and chart recorder paper tray on the Q-Stress cart. Step Place the writing surface brackets into the slots on the right side of the cart.
-
Page 11: Component Placement
System installation on a stress cart Component placement Follow the instructions below for placement of system equipment. Note: The equipment for your system may be different from that shown. Step Place the strap (found in accessory box 1) through the holes in the bottom of the cart. - Page 12 Q-Stress 4.5 System Installation Instructions Step Place the laser printer or chart recorder on top of the cart. Follow printer manufacturer’s Note: instructions to set up the printer. Plug the four component AC power cables into the transformer. (SeeFigure 1 on page 5 appropriate plug placement.) While holding the four AC cables, place the transformer on the...
- Page 13 System installation on a stress cart Step Depending on the type of printer: Connect the USB cable and the • power cord to the printer. • Connect the parallel cable to the chart recorder. Keyboard Blood pressure monitor HASP (optional) Route and connect the printer cable to the upper left USB port on the Video...
- Page 14 Q-Stress 4.5 System Installation Instructions Step Route the mouse and keyboard cables through the hole on the top of the cart; through the hole in the shelf below and plug into the computer. Place the monitor face down on a soft, clean, at surface.
- Page 15 System installation on a stress cart Step Place the monitor arm on the cart and engage the hooks. Caution! A minimum of 6 arm hooks should be engaged.
- Page 16 Q-Stress 4.5 System Installation Instructions Step Secure the monitor mounting post by fastening the security bolt in the hole that lines up with the pen nut on the cart. Attach the power and monitor cables to the monitor. Connect the preamp interface cable from the preamp to the high speed serial port on the computer.
-
Page 17: Install Software
7865 North 86th Street, Milwaukee, WI 53224 U.S.A. • Tel: 1.800.231.7437 • Fax: 1.414.354.4760 • Website: www.mortara.com Technical Support: Tel: 1.888.667.8272 • Email: techsupport@mortara.com Manufactured By: Mortara Instrument, Inc. Mortara, Quinton, and Q-Exchange are trademarks of Mortara Instrument, Inc. Copyright ©2014 Mortara Instrument, Inc. All Rights Reserved.
Need help?
Do you have a question about the Quinton Q-Stress 4.5 and is the answer not in the manual?
Questions and answers