Summary of Contents for Abtus TS-01F
- Page 1 Non-Contact Thermal Sensor User Manual Model: TS-01F Firmware Version: bc36725 ABtUS SINGAPORE PTE LTD www.abtussingapore.com...
-
Page 2: Table Of Contents
View Temperature ..........................11 WiFi Settings ............................. 13 Set Date/Time ........................... 16 Record Download ..........................18 Set Device Name ..........................19 Restore to default (Reset) ........................20 Appendix ............................... 21 Specification ............................21 Appearance ............................22 Dimensions............................23 ABtUS SINGAPORE PTE LTD www.abtussingapore.com... -
Page 3: Introduction
No human Contact Fast Scanning High Temperature Alert (Warning display and sound) No software required. Application • Schools, Government institutions, Offices or anywhere with large crowd and constant human detection ABtUS SINGAPORE PTE LTD www.abtussingapore.com P a g e... -
Page 4: Installation - Wall Mount
– 2pcs Anchor – 2pcs – 1pc Optional items Step – 1: Preparation Wall (Concrete 1.1 Mark the position or Partition) of the Thermal Sensor on the wall 1.2 Drill the holes ABtUS SINGAPORE PTE LTD www.abtussingapore.com P a g e... - Page 5 2.2 Insert the Plastic Butterfly anchor into the drilled holes *Ensure the label is at bottom 2.3 Secure with Phillips orientation as tapping screws and shown washers 2.1 Remove the Cover by turning anticlockwise ABtUS SINGAPORE PTE LTD www.abtussingapore.com P a g e...
- Page 6 *Note: Do not use tissue or towel paper to clean the lens. This sensor is not waterproof, please do not place the sensor in a humid place. ABtUS SINGAPORE PTE LTD www.abtussingapore.com P a g e...
-
Page 7: Basic Operation
Connect to sensor via Wifi Turn on the sensor power. Using laptop/android phone, search and connect to sensor SSID and key in the password: SSID: Human_Thermometer_.. Password: antivirus ABtUS SINGAPORE PTE LTD www.abtussingapore.com P a g e... - Page 8 Using Google Chrome , key in the IP address (Default: 192.168.4.1) of the sensor: ABtUS SINGAPORE PTE LTD www.abtussingapore.com P a g e...
-
Page 9: Calibration
Enter the Temperature value (Reference value) obtained by the ear / forehead thermometer (i.e. 36.6⁰C), followed by press “Confirm”. When the temperature value disappear, it means that the reference value has been loaded into the sensor. ABtUS SINGAPORE PTE LTD www.abtussingapore.com P a g e... - Page 10 Ensure the sensor is placed around the face/neck level. Position yourself 10cm away from the sensor. Press “Confirm”, then wait for 5 seconds. Step 3: Position yourself 80cm away from the sensor. Press “Confirm”, then wait for 5 seconds. ABtUS SINGAPORE PTE LTD www.abtussingapore.com P a g e...
- Page 11 Once done, press “Exit” and it will go back to Homepage. Lastly, under “View Temperature”, press “View” to check if the temperature is accurate based on the calibrated reference value entered earlier (For this case, the reference value was 36.6⁰C). ABtUS SINGAPORE PTE LTD www.abtussingapore.com P a g e...
-
Page 12: User Interface
User Interface Homepage ABtUS SINGAPORE PTE LTD www.abtussingapore.com 10 | P a g e... -
Page 13: View Temperature
View Temperature “View Temperature” displays the following information: Temperature (⁰C) Date & Time ABtUS SINGAPORE PTE LTD www.abtussingapore.com 11 | P a g e... - Page 14 (<10cm): Warning label will displayed and buzzing sound will be alert when a person is having a high fever (where the temperature exceeds the threshold value (i.e. 37.5⁰C)): ABtUS SINGAPORE PTE LTD www.abtussingapore.com 12 |...
-
Page 15: Wifi Settings
WiFi Settings WiFi Settings allow the sensor to connect to existing network. ABtUS SINGAPORE PTE LTD www.abtussingapore.com 13 | P a g e... - Page 16 Key in the existing network SSID and Password which required the sensor to connect to. (An example shown below, i.e. SSID: Linksys09062…..) Step 2: Key in the mDns name to allow sensor mDns name to be found in the existing network. ABtUS SINGAPORE PTE LTD www.abtussingapore.com 14 | P a g e...
- Page 17 Use the laptop/android phone to connect to the existing network which was set in Step 1. Open the web browser and key in the sensor IP address assigned / mDns link (an example shown below): For mDns link: Key in “http://<mDns name>.local *Note: ABtUS SINGAPORE PTE LTD www.abtussingapore.com 15 | P a g e...
-
Page 18: Set Date/Time
Set Date/Time *Note: By default, time is taken from browser. Steps to configure NTP time: ABtUS SINGAPORE PTE LTD www.abtussingapore.com 16 | P a g e... - Page 19 Manual time and date settings are only advice to use when the laptop/phone device time is not accurate and when there is no NTP server to sync to. (For manual time/date setting, the date and time cannot be remain after restart as there is no battery in the sensor.) ABtUS SINGAPORE PTE LTD www.abtussingapore.com 17 |...
-
Page 20: Record Download
(i.e. androidxls app) An example of data log shown below: ABtUS SINGAPORE PTE LTD www.abtussingapore.com 18 | P a g e... -
Page 21: Set Device Name
Set Device Name To set sensor name to appear on every page. Example of sensor device name shown on the homepage: ABtUS SINGAPORE PTE LTD www.abtussingapore.com 19 | P a g e... -
Page 22: Restore To Default (Reset)
2. Open up the front cover of the sensor casing 3. Press and hold the reset button for 2 seconds 4. The sensor will restart automatically and restored to default settings. ABtUS SINGAPORE PTE LTD www.abtussingapore.com 20 | P a g e... -
Page 23: Appendix
Temperature Error: ± 0.7⁰C Protocol: 2.4GhZ Wifi SD Card Storage Format: .csv Comes with 16GB micro SD card Operated By: 12VDC, 1A Power Consumption: <2W ABtUS SINGAPORE PTE LTD www.abtussingapore.com 21 | P a g e... -
Page 24: Appearance
Appearance ABtUS SINGAPORE PTE LTD www.abtussingapore.com 22 | P a g e... -
Page 25: Dimensions
Dimensions Unit: mm ABtUS SINGAPORE PTE LTD www.abtussingapore.com 23 | P a g e...