Advertisement
Cordless Pail Pump Application System
Our Pail Pump Spray System was designed and is manufactured by
Seal 'n Lock System Corporation for the application of its paver
protection products with a safe environmental cleanup. Just simply
attach the commercial spray wand to the spray handle, make sure the
wand is tightened and it is ready to use. DeWalt ® 20-volt slide
batteries and charger may be purchased separately.
This pail pump was designed for easy use and durability. Seal 'n Lock System's
features allow you to dispense product content in half the time of conventional
hand pumps.
Make sure to read the clean out procedures on page 5 especially if you are using
our Super Wet two-part urethane.
Use only for DeWalt® 20-volt slide batteries.
Make sure the Snap Lid is fully secured before lifting, to prevent spillage.
Make sure to test pump before going on Job Site.
Make sure to remove water from the pump system for winterization.
Seal 'n Lock System Corporation
813-852-1500
'ALL IN ONE DAY'
THE FIRST
Operation Manual
www.sealnlock.com
PROCESS
02-01-13
Page 1 of 7
Advertisement
Table of Contents
Summary of Contents for Seal ‘n Lock Pail Pump System
- Page 1 ‘ALL IN ONE DAY’ THE FIRST PROCESS Operation Manual Cordless Pail Pump Application System Our Pail Pump Spray System was designed and is manufactured by Seal ‘n Lock System Corporation for the application of its paver protection products with a safe environmental cleanup. Just simply attach the commercial spray wand to the spray handle, make sure the wand is tightened and it is ready to use.
- Page 2 Not for use with Solvent Base Sealers When inserting batteries into the battery ports. Make sure that you insert the batteries into the ports as straight as you can without bending the contacts causing electrical damage to the pump. LIMITED WARRANTY DO NOT ATTEMPT TO SERVICE THE UNIT BY REMOVING THE COVER REMOVAL OF THE UNIT COVER WILL VOID THE WARRANTY Seal ‘n Lock System Corporation warrants this product to be free from material or workmanship defects for a...
- Page 3 RULES FOR SAFE OPERATION The purpose of safety symbols & notes within this manual are to attract your attention to potential dangers. The safety symbol / notes and the explanations accompanying them, deserve your careful attention and understanding. These warnings do not themselves eliminate any danger and should not serve as a substitute for proper accident prevention measures.
- Page 4 OPERATION Seal ‘n Lock System Corporation’s Cordless Pail Pump Spray System utilizes the popular SHURflo® pump technology and DeWalt® Rechargeable 20 Volt Batteries. It is designed for our sealer (not solvent based sealers) as it has no metals in the path through the pump containing Viton® Valves and Santoprene® Diaphragms. ...
- Page 5 THIS PAIL PUMP IS DESIGNED AND MANFACTURED BY SEAL ‘N LOCK SYSTEM CORPORATION. DO NOT USE WITH ANY OTHER LIQUIDS AS IT WILL CONTAMINATE OUR PAVER PROTECTION PRODUCTS. CLEAN-UP Any type of sprayer will not function satisfactorily if the unit is not cleaned out thoroughly. Clean the sprayer ASAP after each use by completely flushing the unit, including all hoses and wand with manufacturers recommended cleaner until all traces of sprayed material has been removed.
- Page 6 TROUBLE SHOOTING SPRAYER WILL NOT START: To see if the batteries are properly seated and fully charged. To see if the contacts in the battery port are bent. To see if the On/Off switch is in the on position. SPRAYER WILL NOT PRIME: ...
- Page 7 IMPORTANT READ BEFORE USE 1. Make sure pump is functional before use. Check before going on jobsite. 2. Pail Pump must be cleaned out as soon as you are finished sealing. 3. Use your metered pail (see attachment) for the clean-out. Use a scour pad after adding your clean-out solution to remove the urethane that will stick to the inside surface of the pail.
Need help?
Do you have a question about the Pail Pump System and is the answer not in the manual?
Questions and answers