Subscribe to Our Youtube Channel
Summary of Contents for Unitron Johansson 5951
- Page 1 User Manual Remote Management Unit Ref. 5951 - 5952 RMU (REF. 5951) RMU WITH INTEGRATED SMART POWER SUPPLY (REF. 5952)
-
Page 2: Table Of Contents
No part of this manual may be copied, reproduced, transmitted, transcribed or translated into any language without permission. Unitron reserves the right to change the specifications of the hardware and software described in these manuals at any time. Unitron cannot be held liable for any damages resulting from the use of this product. -
Page 3: Introduction
RMU (REF. 5951) - RMU SMART POWER SUPPLY (REF. 5952) 1. I NTRODUCTION Product description REMOTE MANAGEMENT UNIT (RMU) • Enables you to remotely configure and monitor a specific headend installation. • This drastically reduces on-site maintenance, saving you time and money. •... -
Page 4: Safety Instructions
RMU (REF. 5951) - RMU SMART POWER SUPPLY (REF. 5952) Safety Instructions Read these instructions carefully before connecting the unit To prevent fire, short circuit or shock hazard: • Do not expose the unit to rain or moisture. • Install the unit in a dry location without infiltration or condensation of water. •... -
Page 5: Installation Of The Hardware
RMU (REF. 5951) - RMU SMART POWER SUPPLY (REF. 5952) 2. I NSTALLATION OF THE HARDWARE Before mounting, install all DMH modules in the sub-rack. Place the power supply (ref. 5050W) in the far-left slot of the rack. The DMH modules can now be added to the next slots. Install the RMU as the last module. -
Page 6: Remotely Accessing The Rmu With U Cloud
RMU (REF. 5951) - RMU SMART POWER SUPPLY (REF. 5952) locations (new installations) and manage all your existing locations from a single remote connection. • If you don’t have an internet connection you will need to connect both your pc and the RMU to the same network. -
Page 7: Alarm And Monitoring (Optional)
RMU (REF. 5951) - RMU SMART POWER SUPPLY (REF. 5952) 4. A LARM AND ONITORING (OPTIONAL) For Alarm and Monitoring click on “System“ in your headend. • Monitoring: For Real-time Monitoring go to “Monitoring” tab. See appendix of this manual for overview of alarm logs. •... -
Page 8: Ref 5952: Back - Up Power Supply
RMU (REF. 5951) - RMU SMART POWER SUPPLY (REF. 5952) • Alarm: For setting alarm triggers go “Alarm” tab. To select for which headends you want to receive an email with the alarm messages, go to the overview page en select alarms 5. -
Page 9: Technical Specifications
RMU (REF. 5951) - RMU SMART POWER SUPPLY (REF. 5952) ECHNICAL PECIFICATIONS Remote Management Unit DC Connectors 4 x banana sockets RJ-45 Standard: Ethernet 10/100/1000Base-T Ethernet connector Version: IPv4 (IPv6 ready) Mode: Full-duplex Protocols: ARP, ICMP, TCP/IP, HTTP, FTP, DHCP 1 x alarm LED LEDs 1 x power LED... -
Page 10: Conditions Of Warranty
If during this period of warranty the product proves defective, under normal use, due to defective materials or workmanship, Unitron N.V, at its sole option, will repair or replace the product. Return the product to your local dealer for reparation... -
Page 11: Appendix : Alarm And Monitoring Messages
RMU (REF. 5951) - RMU SMART POWER SUPPLY (REF. 5952) 8. A PPENDIX LARM AND ONITORING MESSAGES Device info messages Message Temperature is #{value} Tuner #{tunerId} is unlocked Tuner #{tunerId} is locked Tuner #{tunerId} signal level is #{value} Tuner #{tunerId} signal quality is #{value} Tuner #{tunerId} signal to noise ratio is #{value} dB Tuner #{tunerId} stream becomes unsynchronized Tuner #{tunerId} stream becomes synchronized... -
Page 12: General Info Messages
RMU (REF. 5951) - RMU SMART POWER SUPPLY (REF. 5952) General info messages Message Device has been activated Updating device Scanning device Device is found Device becomes connected Device becomes disconnected Device becomes synchronized Device lost synchronization Warning messages Message Explanation Solution Temperature OK again on subpart nr.#{subcode}... -
Page 13: Error Messages
RMU (REF. 5951) - RMU SMART POWER SUPPLY (REF. 5952) Error messages Message Explanation Solution Hardware malfunction on subpart nr.#{subcode} Hardware problem. If this error persists after reboot, Contact Internal communication failure on subpart Communication issue between components on manufacture. nr.#{subcode} the board. - Page 14 RMU (REF. 5951) - RMU SMART POWER SUPPLY (REF. 5952) UNITRON NV Frankrijklaan 27 B-8970 Poperinge Belgium T +32 57 33 33 63 F +32 57 33 45 24 sales@unitrongroup.com www.unitrongroup.com...
Need help?
Do you have a question about the Johansson 5951 and is the answer not in the manual?
Questions and answers