Subscribe to Our Youtube Channel
Summary of Contents for gofanco PRO-FiberIP Series
- Page 1 ® PRO-FiberIP HDMI over IP (fiber) Uncompressed Multicast System User‘s Guide Receiver Transmitter Made in Taiwan...
- Page 2 ® PRO-FiberIP Congratulations for owning a gofanco product. Our products aim to meet all your connectivity needs wherever you go. Have fun with our products! Please read this manual carefully before first use. If you need more information about our products, please visit www.gofanco.com.
-
Page 3: Table Of Contents
® PRO-FiberIP Table of Contents 1. Safety and Notice ..............3 2. -
Page 4: Introduction
® PRO-FiberIP 2. Introduction The PRO-FiberIP HDMI over IP (fiber) Uncompressed* Multicast System boosts up your video/audio transmission distance up to 300m(1000ft) over a duplex, LC termi- nated multimode fiber cable in Ultra-HD 4K2K@30 format. Users can readily extend Ultra-HD sources from DVD players, Blu-ray Disc player, PS3, PC, and any other HDMI sources broadcasting to distant display monitors including HDMI or DVI enabled TV sets or LCD PC monitors. -
Page 5: Specification
® PRO-FiberIP 4. Specifications Item Description PRO-FiberIP-TX PRO-FiberIP-RX Technical Transmitter [TX] Receiver [RX] Role of usage HDMI compliance HDMI Deep Color, full 3D & 4K2K@30 HDCP compliance Video bandwidth Single-link 340MHz [10.2Gbps] Video support 480i / 480p / 720p / 1080i / 1080p60 / 4K2K@30 / 4K2K@60 4:2:0 8bit HDMI over fiber Audio support Surround sound (up to 7.1ch) or stereo digital audio... -
Page 6: Package Contents
® PRO-FiberIP 5. Package Contents • 1x PRO-FiberIP [TX & RX] • 1x IR blaster • 1x IR receiver • 2x DC 5V • 1x Installation software CD • 1x User Manual 6. Connection Diagram... -
Page 7: Panel Description
® PRO-FiberIP 7. Panel Description Transmitting unit PRO-FiberIP-TX Front Panel 1. +5V DC: Connect to a 5V power supply unit 2. HDMI IN: Connect to an HDMI source with an HDMI male-male cable 3. Status LED: Lights up when the device’s firmware is read 4. - Page 8 ® PRO-FiberIP Receiving unit PRO-FiberIP-RX Front Panel 1. +5V DC: Connect to a 5V power supply unit 2. HDMI OUT: Connect to a display source with an HDMI male-male cable 3. Status LED: Lights up when the device’s firmware is read 4.
-
Page 9: Ir Pass-Through
® PRO-FiberIP 8. IR Pass-Through IR Extenders IR Blaster IR Receiver IR Sockets IR BLASTER: plug in the IR blaster to emit all IR command signals received from the IR receiver from the other end to control the devices corresponding to the IR signals. IR RECEIVER: plug in the IR receiver to receive all IR command signals from the IR remote controls of the corresponding devices. -
Page 10: Notice
® PRO-FiberIP 9. Notice Type A (Receptacle) HDMI Pin 1 TMDS Data2+ Pin 11 TMDS Clock Shield Pin 2 TMDS Data2 Shield Pin 12 TMDS Clock– Pin 3 TMDS Data2– Pin 13 Pin 4 TMDS Data1+ Pin 14 Reserved (N.C. on device) Pin 5 TMDS Data1 Shield Pin 15... -
Page 11: Operation Approach
® PRO-FiberIP 10.Operation Approach Software Control through Ethernet port 1. System Requirement (1) OS information : MS Win XP/7/8/10 (2) Baud Rate: 57600 (3) Software size: 17MB (4) Minimum RAM requirement: 256MB 2. Control Interface Before you execute the software, please open the software control pro- gram (based on your operating system). - Page 12 ® PRO-FiberIP (1) Video Switching (Mapping) Dragging the Encoders icon to Decoders icon to do input/output mapping. After set- ting the mapping, you also can click the right button to set up more video mode (ex. stop video). (2) Wall Switching User can define wall size by entering the wall parameters.
- Page 13 ® PRO-FiberIP (3) HDMI/Analog Audio Routing This function provides you to control where the audio transmit. (4) RS-232 Routing Bi-directional RS-232 signal are transmitted between the device transmitter and receiver. Dragging the RS-232 icon of Senders to Receivers to make connection and sending/receiving data.
- Page 14 ® PRO-FiberIP (5) Infrared Routing Bi-directional IR signal can be transmitted between the transmitter and receiver. The IR signal can be generated either from receiver or a control system. You can drag the Infrared Senders icon to Receivers to do the Infrared Routing. (6) Custom Setting In the right part of the control interface, we provide the save function for user to save the video switching (mapping) into the flash memory.
-
Page 15: Warranty
® PRO-FiberIP 11. Limited Warranty The SELLER warrants the PRO-FiberIP HDMI over IP (fiber) Uncompressed Multicast System free from defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer. Should this product fail to be in good working order within 1 year warranty period, The SELLER, at its option, repair or replace the unit, provided that the unit has not been subjected to accident, disaster, abuse or any unauthorized modifi- cations including static discharge and power surge. - Page 16 ® Thank you for choosing gofanco www.gofanco.com Jul, 2019 Ver. A Copyright © by gofanco, LLC. All rights reserved.
Need help?
Do you have a question about the PRO-FiberIP Series and is the answer not in the manual?
Questions and answers