1. Manuals
  2. Brands
  3. e-BLEACH Manuals
  4. Controller
  5. infinity
  6. User manual

e-BLEACH infinity User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
e-BLEACH manual

Advertisement

Table of Contents
loading

Summary of Contents for e-BLEACH infinity

  • Page 1 manual...

  • Page 2: Table Of Contents

    Attached device ................ 17 Using the device ..............18 Remove Battery Protection ............18 Reset Device (find out how many cycles are left on a 'e-BLEACH - 10x4') ..................19 Renew Device to the next cycle ..........20 e-BLEACH - infinity ..............20 e-BLEACH - 10x4 ..............

  • Page 3: Introduction

    - download the latest version of the user manual from the Internet e-BLEACH - infinity The 'e-BLEACH - infinity' is a replacement chip for the Guide of the "ZOOM! Advanced Power" bleaching device. It is designed to enable the lamp for test purposes. It is made in a way where you can always reset the state of the chip to its four times 15 minutes of usage.

  • Page 4: E-Bleach - 10X4

    The 'e-BLEACH - 10x4' is the little brother of the 'e-BLEACH - infinity' for occasional users of the UV lamp. It is a lot cheaper but in the same way limited to nine renew cycles. Like this it is possible to enable the Lamp for ten hours.

  • Page 5: Safety Instructions

    Safety instructions The device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. Keep away from heaters and other heating sources! If the device has been exposed to drastic temperature fluctuation (e.g.

  • Page 6: Exclusion Of Liability

    We are not liable for any property damage or damage to persons. This device is designed only for test purposes or demonstration. Online resources On the website http://www.e-bleach.com you will find always the newest version of this manual in the PDF format and additional video tutorials.

  • Page 7: Mounting The Device

    Remove Chip from existing guide In this section it is explained how you prepare your Guide to work with an e-BLEACH chip The original Guide Your original Guide contains a microchip on a circuidboard which has to be replaced with the e-BLEACH connectorboard.

  • Page 8: Push In The Hooks To Loosening The Chip Cover

    Push in the hooks to loosening the chip cover The circuitboard is held into the guide by a little cover which is clipped into the guide. This cover can be removed by firmly pressing against the hook which is marked in the picture (there are two hooks - one on each side of the chip) Remove the chip cove...

  • Page 9: Prepared Guide

    Turn around the Guide to finally remove the cover by sliding a screwdriver in the gap and lift the cover. Prepared guide Now you have your guide ready to insert the e-Bleach connector board.

  • Page 10: Fix The E-Bleach Device By Using The Cover Clip

    Fix the e-BLEACH device by using the cover clip There are several ways to finally fix your e-BLEACH device in the plastic of an existing Guide. The best way to do this is by using the removed cover clip like explained in this section.

  • Page 11: Prepare The Clip

    Prepare the clip Take the plastic cover you removed before from the guide and cut it with a tool like a (saw; side cutter; cutting wheel; scissors; etc) in two pieces like illustrated in the image. The important piece is the part having the hooks.

  • Page 12: Insert E-Bleach Connector

    Insert e-BLEACH connector Insert the connector board of the e-BLEACH device like displayed in the picture. Insert the clip Clip in the left over piece of the plastic cover clip. It should go all the way in and hold the connector board firmly inside the Guide.

  • Page 13: Prepared Guide

    Prepared Guide Now the device should look like in the above picture and be ready to be connected to the Lamp.

  • Page 14: Fix The E-Bleach Device By Using Glue (Only If No Cover Clip Present)

    Fix the e-BLEACH device by using glue (only if no cover clip present) If you lost your cover clip or it was broken during the preperation process you can also fix the connector board of the e-BLEACH device using any kind of glue.

  • Page 15: Attach E-Bleach To The Lamp

    Attach e-BLEACH to the Lamp Attach Velcro to the Device Attach one part of the Velcro pad included in the package to the device.

  • Page 16: Attach Velcro To The Lamp

    Attach Velcro to the Lamp The matching Velcro pad needs to be fixed on the downside of the Lamp. You can position it using the e-BLEACH device to match the cable length. Attach device to the lamp From now on you can attach and detach the e-BLEACH device easily...

  • Page 17: Attached Device

    Attached device The picture shows the Lamp with the properly mounted e-BLEACH chip.

  • Page 18: Using The Device

    Using the device Remove Battery Protection Before using the e-BLEACH device the battery safer foil has to be removed. For storage and unwanted battery discharging the battery is protected by foil which has to be removed before the chip can be used.

  • Page 19: Reset Device (Find Out How Many Cycles Are Left On A 'E-Bleach - 10X4')

    Reset Device (find out how many cycles are left on a 'e- BLEACH - 10x4') To see how many sessions are left on a 'e-BLAECH - 10x4' just press the reset button short and see the red LED. After pressing the reset button the LED will first doubleflash. Then it will flash as many times as you can renew the device.

  • Page 20: Renew Device To The Next Cycle

    - infinity Having the 'e-BLEACH - infinity' you can renew your device as often as you like. Even if you only used the device for one session you can always renew it to the full four sessions.

  • Page 21: Press The Reset Button Shortly While Keeping The Renew Button Pressed

    Now you can release the renew button as well. If you have the 'e-BLEACH 10x4' and no more cycle left it will only doubleflash and will not renew anymore (there will be no long flash).

  • Page 22: Replace Battery

    Caution: If you do a renew twice, without using the chip on the lamp, you won't see the long flash either but it will be still operational. Replace Battery Read this chapter carefully before replacing the battery. Safety warning Leaky or damaged batteries might cause cauterisation when in contact with the skin;...

  • Page 23: Insert Cr2025 Battery

    Insert CR2025 battery Insert the tray again with the battery inserted in the illustrated direction. Battery disposal...

  • Page 24: Troubleshooting

    Troubleshooting Display shows "Replace Guide" Seeing "Replace Guide" means that your device is working properly but needs to be renewed like described in the renew chapter. Display shows "Improper Guide" If your display shows "Improper Guide" please remove the Guide, and press the reset button shortly.

This manual is also suitable for:

10x4

Table of Contents