Summary of Contents for GameKeeper HU2284801-GK
- Page 1 450 LB WILDLIFE FEEDER Assembly and Operating Instructions Model # HU2284801-GK 1 of 22 HU2284801-GK - ENG 20180502-V1.0...
-
Page 2: Pay Attention
Wrench etc….. DANGER Your GameKeeper Feeder is designed, engineered and constructed in a manner that makes it a rugged piece of hunting equipment that will give you years of service. This rugged construction makes your feeder physically heavy. As such, you should never attempt to assemble this feeder alone. YOU MUST HAVE A MINIMUM OF TWO (2) ADULTS FOR THE SAFE ERECTION OF YOUR FEEDER. - Page 3 GENERATORS, SUBSTATIONS, ETC) AND/OR TRANSMISSION EQUIPMENT (POWER LINES). FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH! DO NOT LOAD FEED WITHOUT ANOTHER ADULT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH! 3 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 4 PRIOR TO THE FIRST TIME OF OPERATION. ALWAYS REFER TO THE USER GUIDE OF THE BATTERY FOR DIRECTION. THE PROPER SPACING BETWEEN THE SPIN PLATE AND THE FUNNEL IS 3/8 INCH. THIS IS VERY IMPORTANT FOR SERVICE FREE OPERATION. 4 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 5 FOR REPLACEMENT OF MISSING OR DEFECTIVE PARTS. Symbol: The following symbols will be shown in assembly procedures for indication of tightening the bolt and nut if necessary. Hand Tighten only at this time Tighten with tools at this time 5 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 6 Product Diagram TK11 TK13 TK12 TK14 6 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 7 Hardware List – For Feeder Item No. Item Name Diagram Hex. Bolt 8 pcs (M8x20) Hex. Bolt 32 pcs (M8x15) Locking Nut 36 pcs (M8) Flat Washer 72 pcs (M8) Hex. Bolt 4 pcs (M6x20) 7 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 8 Hardware List – For Timer Kit Item Item Name Diagram Hex. Bolt 10 pcs (M6x20) Flat Washer 2 pcs (M6) Butterfly Nut 2 pcs (M6) Flange Nut 2 pcs (M6) Wing Bolt 1 pc 8 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 9 #D - 16 pcs Leave these top holes on Lower Leg (#4) for Step #3. DO NOT attach bolts now Do not attach bolts to top holes of Leg #4 in this step 9 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 10 #3 (front & rear) on this side (4 pcs) Leg #3 Under leg bracket of hopper Leg #3 On Top of for assembly leg bracket of hopper for assembly 10 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 11 Each Leg Support (#9) attaches to ONE FACE of Lower Legs (#4) with 2 bolts only. NOT ALL top holes on Lower legs (#4) reserved in Step #1 are required for assembly of Leg Supports (#9). 11 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 12 Step 4. Attach Sled Foot (#6) to legs per below. Tighten all bolts in Step #2,3,4 with tool. Hardware required: #B – 4 pcs #C – 4 pcs #D – 8 pcs 12 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 13 Step 6. Assembly of Timer Kit. Hand Tighten bolts Hardware required: TK13 #M - 2 pcs #N - 2 pcs #P - 2 pcs #Q - 2 pcs #R - 1 pc TK12 13 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 14 #M - 4 pcs Step 8. Attach Varmint Guard (#7) to hopper. TIGHTEN bolts with tool. Hardware required: #E - 4 pcs #G – 4 pcs Door of Varmint Guard aligns with door of Timer Kit 14 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 15 #D - 4 pcs #F - 2 pcs Step 10. Put the lid on hopper body and lock it. Affix the feeder to the ground with Stakes (#5). … YOUR FEEDER IS COMPLETELY ASSEMBLED, 15 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 16 DO NOT LOAD FEEDER UNTIL IT IS STANDING UP AND IN PLACE. THE PROPER SPACING BETWEEN THE SPIN PLATE AND THE FUNNEL IS 3/8 INCH. THIS IS VERY IMPORTANT FOR SERVICE- FREE OPERATION. 16 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 17 REGULATIONS. PLEASE ALWAYS KEEP YOUR INFORMATION UP-TO-DATE AND RELIABLE. MANY STATE LAWS CHANGE AND ARE AMENDED WITHOUT NOTICE. ALWAYS DOUBLE CHECK YOUR STATE AND SPECIFIC COUNTY FEEDING LAWS REGARDING THE USE OF FEEDERS. 17 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 18 DO NOT LOAD FEEDER UNTIL IT IS COMPLETELY ASSEMBLED AND STANDING UP IN PLACE. DO NOT LOAD THE FEEDER IF YOU FIND ANY OF PART #5 (STAKES) MISSING, DAMAGED AND/OR LOOSE. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH! 18 of 22 HU2284801-GK - ENG 20180502-V1.0...
-
Page 19: How To Install Battery
CONNECTING THE BATTERY IN ANY OTHER WAY WILL PERMANENTLY DAMAGE YOUR UNIT. TAKE EXTREME CARE TO MAKE THIS CONNECTION PROPERLY. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH. 19 of 22 HU2284801-GK - ENG 20180502-V1.0... -
Page 20: How To Operate The Timer
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: - THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. - THE DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS UNIT AROUND POWER GENERATING EQUIPMENT 20 of 22 HU2284801-GK - ENG 20180502-V1.0... - Page 21 Please contact Customer Service at Rankam (China) Manufacturing Company Limited 1-888-837-1380 Monday thru Friday 8 A.M. to 5 P.M. Pacific Standard Time or by email customerservice@rankam.com WE CAN HELP. Made in China 21 of 22 HU2284801-GK - ENG 20180502-V1.0...
- Page 22 Follow the Customer Service Representative’s instructions exactly. If a return is necessary, it must be packed carefully and shipped prepaid. Rankam (China) Manufacturing Company Limited 18 F., New Lee Wah Centre 88 Tokwawan Road, Kowloon, Hong Kong 22 of 22 HU2284801-GK - ENG 20180502-V1.0...